Related Manuals for Haier 10515222
Summary of Contents for Haier 10515222
-
Page 1: Operation Manual
SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU-12CR03-Y HSU-18CR03-Y Please read this operation manual before using the air conditioner. 0010515222... - Page 3 Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier. Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.
-
Page 4: Specifications
Cautions Do not obstruct or cover the ventilation grille of the air conditoner.Do not put fingers or any other things into the inlet/outlet and swing louver. Do not allow children to play with the air conditioner.In no case should children be allowed to sit on the outdoor unit. -
Page 5: Safety Instruction
Installation Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage. lnstallation in a inadequate place may cause accidents. Do not install in the following place. - Page 6 Cautions When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop. Connect power supply cord to the outlet completely STRICT ENFORCEMENT Do not use power supply cord in a bundle. PROHIBITION Do not start or stop the operation by disconnecting the power supply cord and so on.
-
Page 7: Parts And Functions
Parts and Functions Indoor unit Outlet Inlet Inlet grille Anion generator (inside) Vertical blade(inside) (adjust left and right air flow) Outdoor unit OUTLET INLET display board(inside) (adjust up and down air flow Don't adjust it manually) Power plug CONNECTING PIPING AND ELECTRICAL WIRING DRAIN HOSE air ionization purify layer (inside) -
Page 8: Parts And Functions
Parts and Functions PURIFY FRESH POWER/SOFT 1.CODE Used to select CODE A or B with a press,A or B will be displayed on LCD. Please select A without special explanation. 2.RESET When the remote controller appears abnormal, use a sharp pointed article to press this button to reset the remote controller normal. -
Page 9: Clock Set
Parts and Functions Clock Set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: 1. Press CLOCK button,"AM" or "PM" flashes. 2. Press to set correct time. Each press will increase or decrease 1 min. -
Page 10: Operation
Press Purify button. is displayed on the remote controller and is displayed on the display board . Air conditioner starts air ionization purify and health anion function operation. For twice press, When indoor fan motor is running, it has purify and healthy process function. -
Page 11: Auto Operation
Press FAN button. For each press, fan speed changes as follows: Remote controller: Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5.Unit stop Press ON/OFF button, the unit stops. -
Page 12: Cool Operation
Press FAN button. For each press, fan speed changes as follows: Remote controller: Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5.Unit stop Press ON/OFF button, the unit stops. -
Page 13: Dry Operation
4.Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp.setting+2 at LOW speed regardless of FAN setting. -
Page 14: Fan Operation
Display board Remote controller PURIFY FRESH POWER/SOFT 1. Unit start Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO Then Select FAN operation 3.Fan speed selection Press FAN button. -
Page 15: Air Flow Direction Adjustment
Air Flow Direction Adjustment 1.Status display of air sending PURIFY FRESH POWER/SOFT 2.Up and down air flow direction For each press of as follows according to different operation modes: COOL/DRY/FAN remote controller: AUTO: Pos.1 remote controller: The horizontal flap will swing according to the above positions 3.Left and right air flow direction For each press of remote controller:... -
Page 16: Display Board
Operation Display board Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. Use of SLEEP function After the unit starts, set the operation status, then press SLEEP button before which the clock must be adjusted and time being set. -
Page 17: Timer On/Off Operation
Operation Display board Remote Controller FRESH POWER/SOFT Hints: After replacing batteries or a power failure happens, time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if time setting is the same as previous one. Timer On/Off Operation Set clock correctly before starting TIMER operation. - Page 18 Operation Display board Remote Controller FRESH POWER/SOFT Timer On-Off Operation Set clock correctly before starting TIMER operation. 1. After unit starts, select your desired operation mode . Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: TIMER ON...
- Page 19 Operation POWER Operation Remote controller When you need rapid cooling, you can use this function. Selecting of POWER operation Press POWER/SOFT button. Every time the button is pressed, display changes as follows: Stop the display at In POWER operation status: In COOL mode, compressor runs in high frequency FRESH for 15 min then returns to original status setting.
-
Page 20: Health Airflow Operation
2.In cooling, it is better to select the mode. 3.In cooling and dry, using the air conditioner for a long time under the high air humidity, a phenomenon falling drips of water occurs at the outlet grille . -
Page 21: Emergency Operation
Operation Emergency and Test Operation Emergency operation Use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed,the" Pi "sound is heard once, which means the start of this operation. In this operation, the system automatically selects the operation modes, cooling or fan, according to the room temperature. -
Page 22: Maintenance
Maintenance For Smart Use of The Air Conditioner Setting of proper room temperature Close doors and windows during operation During cooling operation prevent the penetration of direct sunlight with curtain or blind If the unit is not to be used for a long time, turn off the power supply main switch. -
Page 23: Air Filter Cleaning
Close the inlet grille. Indoor Body Wipe the air conditioner by using a soft and dry cloth.For serious stains,use a neutral detergent diluted with water.Wring the water out of the cloth before wiping.then wipe off the detergent completely. -
Page 24: Aip/Vc Layer + Bacteria-Killing Medium Sets
Maintenance The installation and cleanout AIP layer, VC layer + Bacteria-killing medium sets 1.Open the lnlet Grille The inlet grill is supported by its top plate at the right side. 2.Detach the standard air filter Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward. - Page 25 Maintenance To Keep Your Air conditioner in Good Condition after Season. 1. Operate in cooling mode for 2-3 hours. To prevent breeding mold or bad smell, be sure to operate at the designated temperature or 30 mode and High speed fan mode for 2-3 hours.
- Page 26 Maintenance Before Setting in High season 1. Cleaning the standard air filter. Operation without filter may cause troubles.Be sure to attach both right and left filters prior to the operation. Each of them are of different shapes. 2. Connecting the earthing cable. Incomplete earthing may cause an electric shock.
-
Page 27: Troubleshooting
When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner. During unit operation or at stop, a swishing or gurgling noise may be heard. At first 2-3 minutes after unit start, this noise is more noticeable.