American Standard TROPIC 7038.400 Installation Instructions Manual page 7

TROPIC
Bidet Faucet and Vacuum Breaker
EverClean™ Finish & SpeedConnect™ Drain
Congratulations on purchasing your American Standard faucet
with EverClean finish and Speed Connect drain, two features
found only on American Standard faucets.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
*Your new American Standard faucet is designed to work only with the SpeedConnect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Roughing-in Dimensions
TRANSFER VALVE (FOR FLUSHING
RIM OR SPRAY)
BIDET OUTLINE
7/8 DIA.
IS SYMBOLIC
ADJ. 1-1/4 2-1/8
DOUCHE SPRAY
DIA.
TO 2-1/4
1-3/8
3-7/8
DIA.
5-1/2
1
BIDET FAUCET INSTALLATION
Place RUBBER RING (10) into DECK ADAPTER (4).
Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From
under side of mounting surface, install VALVE BODY (3, 3a) through valve mounting
holes. Threads of VALVE BODY (3, 3a) should extent at least 5/16 of a inch above
mounting surface top. Fig. A. Thread DECK ADAPTER (4) onto VALVE BODIES (3, 3a)
until snug against internal stop. If necessary, adjust LOCKNUT (1).
Tighten LOCKNUTS (1) with WRENCH (5) (supplied)
to secure VALVE BODIES (3, 3a).
Remove MOUNTING NUT (6), WASHER (7) and
UPPER GASKET (8) from TRANSFER VALVE (9).
Insert TRANSFER VALVE (9) into the center forward
hole of BIDET.
Replace UPPER GASKET (8) and WASHER (7) . Position
the side threaded outlet rearward and secure MOUNTING
NUT (6). Thread ESCUTCHEON (11) onto TRANSFER
VALVE (9) until it seats against the BIDET LEDGE.
2
SPRAY INSTALLATION
Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside
of SPRAY BODY FLANGE (2) and secure with NUT (3).
Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1).
Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet
NIPPLE (7) of the TRANSFER VALVE (8).
Thread SPRAY CAP (9) onto SPRAY BODY (1).
1-3/16 DIA.
1-1/4 MAX.
FINISHED
FINISHED
FLOOR
WALL
1-1/4 O.D. TAILPIECE
CAUTION
Installation
Instructions
7038.401
with
SpeedConnect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
8 TO 12
DIVERTER AND
VACUUM BREAKER
ASSEMBLY
2-1/4
(C) (H)
DIA.
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
Turn off hot and cold water
supplies before beginning.
Fig. A.
5/16''
MOUNTING
MIN.
SURFACE
3, 3a
8
7
6
1
Certified to comply with ANSI A112.18.1
Required tools
Screwdriver
Phillips Screwdriver
Adjustable Wrench
11
4
10
4
10
3
2
HOT
1
2
1
5
2
PUTTY
3
4
M 9 6 8 8 9 4
Plumbers' Putty or
Caulking
Channel Locks
Tubing Cutter
6
7
BIDET
LEDGE
3a
COLD
8
9
9
1
5
4