Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
The for information and other details concerning warranty. prices charged by Wells Bloomfield for its products are SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS Resetting of safety thermostats, circuit breakers, over cleaning schedules, are customer responsibility.
SERVICING INSTRUCTIONS PARTS & SERVICE INTRODUCTION Thank You for purchasing this Wells Bloomfield appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
PRECAUTIONS AND GENERAL INFORMATION WARNING: Electric Shock Hazard All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. WARNING Electric Shock Hazard Warmer must be properly grounded to prevent possible shock hazard.
Provided non-skid feet Models HD8799 and HD8802 dispensers are equipped with a must be installed at each corner cord and plug. They requires a 115 - 125 volt circuit (50/60 Hz, of the unit.
Pour product into warming tank. Using pre-heated product will reduce heat-up time. Model HD8799 utilizes a fixed thermostat to hold product at 140ºF (60ºC). NOTE: Product may continue Model HD8802 thermostat may be adjusted to hold to flow for several seconds after product at 170ºF (77ºC) maximum.
CLEANING INSTRUCTIONS PROCEDURE: Clean Heated Dispenser CAUTION: Electric Shock PRECAUTIONS: Disconnect dispenser from electric power. Hazard Drain product and allow dispenser to cool. Do not submerge or immerse FREQUENCY: Daily or after draining product from dispenser in water. dispenser CAUTION: TOOLS: Mild Detergent, Clean Soft Cloth or Sponge Burn Hazard...
TROUBLESHOOTING SUGGESTIONS SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY Not plugged in or circuit breaker Restore electric power to warmer off or tripped Power switch not ON Turn power switch to ON Inspect wiring for burnt wires and Internal wiring damage proper connections . Repair as Appliance will not heat needed Power cord damaged...
EXPLODED VIEW & PARTS LIST MODEL HD8799 2½-GALLON DISPENSER ITEM PART NO DESCRIPTION ITEM PART NO DESCRIPTION 2U-75865 FAUCET ASSEMBLY 2N-75853 HEATING ELEMENT 120V 200W BODY FAUCET 2T-75863 THERMOSTAT 140ºF 120V 1.1* 2U-71460 SEAT CUP 2E-30169 SWITCH 250V DPST 1.2* ASSEMBLY, HANDLE &...
Page 11
EXPLODED VIEW & PARTS LIST MODEL HD8802 5-GALLON DISPENSER ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION 2U-75865 FAUCET ASSEMBLY 2N-75853 HEATING ELEMENT 120V 200W 1.1* BODY FAUCET DD-304682 THERMOSTAT ADJUST 170ºF 120V 1.2* 2U-71460 SEAT CUP 2E-30330 SWITCH 250V DPST 1.3* ASSEMBLY, HANDLE &...
SERVICING INSTRUCTIONS ACCESS - BOTTOM PANEL CAUTION Electric Shock All internal components are accessible by removing the bottom Hazard panel. Opening the bottom panel will Remove four screws around the bottom of the warmer tank to expose uninsulated electrical free bottom panel from tank assembly. components.
DRIP TRAY ASSEMBLY (pk 6) 2L-71747 filters. For factory authorized service, or to order factory authorized replacement parts, contact your Wells authorized service agency, or call: Wells Bloomfield, LLC 10 Sunnen Dr., P.O.Box 430129 St. Louis MO 63143 USA Service Dept.
Page 16
Commercial Food Equipment Service Association Wells Bloomfield proudly supports CFESA Commercial Food Equipment Service Association SERVICE TRAINING - QUALITY SERVICE SERVICE TRAINING - QUALITY SERVICE Genuine Parts Protect - YOU - All - Ways CUSTOMER SATISFACTION CUSTOMER SATISFACTION WELLS BLOOMFIELD, LLC 10 Sunnen Drive P.O.Box 430195...