Keep work area well lighted. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit SAFETY Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
Page 4
24. BE AWARE OF HOSE LOCATION WHEN RISK TOOLS. Hoses can easily become a tripping hazard when laid across the floor or spread out in a disorganized fashion. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit TOOLS before RECOMMENDED recommended ALLOW UNTRAINED...
Page 5
5. COMPRESSED AIR RATING: Do not connect the nailer/stapler to com- pressed air that exceeds 120 PSI. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit Staplers 6. HOSE USAGE: Make sure your air hose is designed for the tool in use, is in good condition, and is long enough to reach your work without stretching.
Page 6
Use this and other tools with caution and respect. Failure to do so could result in serious personal injury, damage to equipment or poor work results. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit...
Page 7
1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com Web Site: http://www.grizzly.com Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit Tool Data Framing Nailer Nail Size ... ⁄ Nail Strip Angle ... 34º Clipped Head Nail Length ...2"–3½"...
Page 8
C. Safety Goggles ... 1 D. 34° Framing Nailer ... 1 E. 18 Gauge Brad Nailer ... 1 F. 21 Gauge Stapler ... 1 G. Carrying Case ... 1 Figure 1. Model H8233 inventory. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit Inventory...
Compressed Air System The Model H8233 is designed to be oper- ated at the following air pressures using clean, dry, regulated, compressed air: Tool Operating Air Pressure Framing Nailer ... 80–110 PSI Brad Nailer ... 60–100 PSI Stapler ... 60–100 PSI...
Page 10
Serious injury may occur. DO NOT attempt to modify or bypass the safety nose mechanism to make the framing/brad nailer fire without pushing the safety nose down. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit...
Page 11
Figure 3. Sliding magazine pusher back and engaging catch lever. 3. Insert a strip or two of nails, pointed- end down, into the magazine as shown in Figure 4. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit OPERATIONS " Shank Diameter ⁄ "...
Page 12
Figure 8, and slide the magazine pusher all the way for- ward. ⁄ "– ⁄ " Figure 8. Loading staples. 4. Release the magazine latch lever to lock the magazine pusher in place. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit Pusher...
Page 13
Besides damaging your workpiece, deflection can cause injury if your free hand is in the path of the deflecting nail. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit Figure 9. Example of nail deflection. 5. Pull the trigger. Stapler 1. Connect the air supply to the quick con- nect fitting.
3. Remove the nail stick from the maga- zine. 4. Locate the opening in the underside of the nailer safety nose (see Figure 11). Nose Opening Figure 11. Nose opening for clearing a Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit jammed nail.
Page 15
Figure Latch Figure 12. Nose guide cover removed from brad nailer. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit 4. Use needle nose pliers to remove the jammed nail. 5. Replace the nose guide cover, as shown in Figure 13.
Step 3. Note: For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual for component locations. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit...
Ignoring this warning may lead to serious personal injury or even death! Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit Lubricating Standard pneumatic tool oil has been included with your new Grizzly nailer/sta- pler to help maintain its useful life.
Tool does not fire. 1. Tool is not lubricated. 2. Nail/staple is jammed in maga- 3. Piston shaft is damaged. 4. Air pressure too low. Model H8233 3-Piece Framing/Brad Nailer & Stapler Kit are damaged. /staples from moving freely in magazine. of lubrication.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte- nance.