Panasonic WV-CP230 Operating Instructions page 2

CONNECTIONS
A. WV-CP230 (120V AC 60Hz)
Connect the power cord to an electrical outlet
of 120V AC 60Hz.
B. WV-CP232 (12V DC)
Connect the power cord to the DC 12V IN ter-
minal on the rear panel of the WV-CP232.
@ !
12 V DC
(10.5 V - 16 V)
Resistance of copper wire [at 20°C (68°F)]
Copper wire #24 #22 #20
size (AWG) (0.22mm ) (0.33mm ) (0.52mm ) (0.83mm
2 2 2
Resistance
0.078 0.050 0.03.
/m
Resistance
0.026 0.017 0.010
/ft
• Calculation of maximum cable
between camera and power supply :
10.5V DC ≤ V (R x 0.42 x L) ≤ 16V DC
A
L : Cable length (meters)
R : Resistance of copper wire ( /meter)
V : DC output voltage of power supply unit
A
V 12
A
L standard = (meters)
0.42 x R
V 16
A
L minimum = (meters)
0.42 x R
V 10.5
A
L maximum = (meters)
0.42 x R
C. WV-CP234 (24V AC 60Hz)
Connect the power cable to the AC 24 V IN
terminal on the rear panel of the WV-CP234.
1 2
24 V AC, 60 Hz
(19.5 V - 28 V)
Recommended wire gauge sizes for 24 V AC line
Copper wire #24 #22 #20
size (AWG) (0.22mm 2 ) (0.33mm 2 ) (0.52mm 2 ) (0.83mm
(m) 95 150 255
Length
of Cable
(Approx.)
(ft) 314 495 842
Caution:
To prevent fire or electric shock hazard, UL
listed wire VW-1, style 1007 should be used
for the DC 12 V or AC 24 V Input Terminal.
FOCUS OR FLANGE-BACK ADJUSTMENT
The following adjustment should be made by
qualified service personnel or system installers.
q Loosen the screws on the flange-back adjust-
ing ring.
w
Flange-back
qe Adjusting Ring
Screws
Installation of Auto Iris Lens
Connector
Install the lens connector (YFE4191J100) when
using a video drive ALC lens.
The installation should be made by qualified
service personnel or system installers.
Cut the iris control cable at the edge of the lens
connector to remove the existing lens connector
and then remove the outer cable cover of the sup-
plied connector as shown in the diagram.
The pin assignment of the lens connector is as fol-
lows:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used
Pin 3: Video signal; 1.3 V[p-p]/40 k
Pin 4: Shield, ground
Rib
Pin 3
Pin 1
Pin 4
#18
Pin 2
)
2
0.018
Solder the lens cable to the pins of the sup-
plied connector.
0.006
length
Mounting the Lens
Caution:
Before you mount the lens, loosen the two
screws on the ring, and rotate this ring clock-
wise until it stops. If the ring is not at the end,
the inner glass or CCD image sensor may be
damaged.
q Mount the lens by turning it clockwise on the
lens mount of the camera.
w Connect the lens cable to the auto iris lens
connector on the side of the camera.
w
Flange-back
Adjusting Ring
Caution for Mounting the Lens
The lens mount should be a C-mount or CS-mount
(1"-32UN) and the lens weight should be less than
g (0.99 lbs). If the lens is heavier, both the
450
lens and camera should be secured by using the
#18
supporter.
2 )
The protrusion at the rear of the lens should be as
425
shown in the diagram.
1 403
C-mount: Less than 13 mm (1/2")
CS-mount: Less than 8 mm (5/16")
w Turn the flange-back adjusting ring to the
desired position.
Caution: When the C-mount lens is mounted,
do not rotate the ring counterclockwise
by force after it stops. If the ring is rotat-
ed by force, the inner lens or CCD image
sensor may be damaged.
e Tighten the screws on the flange-back adjust-
ing ring.
SPECIFICATIONS
Pick-up Device:
Scanning Area:
Synchronization:
Scanning System:
Scanning:
Horizontal:
Vertical:
Horizontal Resolution:
Video Output:
Signal-to-Noise Ratio:
Electronic Light Control:
Minimum Illumination:
Detail:
Lens Mount:
Ambient Operating Temperature:
Ambient Operating Humidity:
Power Source and
Power Consumption:
Dimensions (without lens):
Weights (without lens):
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
STANDARD ACCESSORIES
Body Cap............................................................................................1 pc.
ALC Lens Connector (YFE4191J100).................................................1 pc.
Screws
q
OPTIONAL ACCESSORIES
Lenses: WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3, WV-LA908C3,
WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LFY3C3,
WV-LFY45C3, WV-LFY9C3
Video Imaging Systems Company
A Division of Panasonic Broadcast & Television Systems Company
A Unit of Matsushita Electric Corporation of America
Executive Office: One Panasonic Way 4H-2, Secaucus, New Jersey 07094
Regional Offices:
Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Southeast: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838
Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211
Southwest: 8105 Beltsline Road, Suite 100, Irving, TX 75063 (927) 915-1334
Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.
San Gabriel Industrial Park, 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00630 (809)750-4300
768 (H) x 494 (V) pixels, Interline Transfer CCD
4.92 (H) x 3.70 (V) mm (Equivalent to scanning area of 1/3"
pick-up tube)
Internal, Line-locked or Multiplexed vertical drive (VD2),
selectable
2 : 1 interlace
525 lines / 60 fields / 30 frames
15.734 kHz
59.94 Hz
480 lines
1.0 V[p-p] NTSC composite 75 / BNC connector
50 dB (AGC OFF, weight ON)
Equivalent to continuous variable shutter speed between 1/60 s
and 1/15 000 s
0.6 lx (0.06 foot-candle) at F0.75 [equivalent to 2.0 lx (0.2 foot-
candle) at F1.4] AGC ON
SHARP or SOFT, selectable
C-mount or CS-mount, selectable
10°C - +50°C (14°F - 122°F)
Less than 90 %
WV-CP230: 120 V AC 60 Hz, 3.9 W
WV-CP232: 12 V DC, 270 mA
WV-CP234: 24 V AC 60 Hz, 3.7 W
67 (W) x 65 (H) x 123 (D) mm
[2-5/8" (W) x 2-9/16" (H) x 4-13/16" (D)]
0.62 kg (1.37 lbs)
WV-CP230:
WV-CP232: 0.4 kg (0.88 lbs)
WV-CP234: 0.43 kg (0.95 lbs)