Grizzly G2790 Instruction Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Grinder
  5. G2790
  6. Instruction manual

Grizzly G2790 Instruction Manual

Universal knife grinder
Hide thumbs Also See for G2790:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
UNIVERSAL KNIFE GRINDER
MODEL G2790
INSTRUCTION MANUAL
COPYRIGHT © 1992 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
REVISED APRIL, 1999. PRINTED IN U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Grizzly G2790

Summary of Contents for Grizzly G2790

  • Page 1 UNIVERSAL KNIFE GRINDER MODEL G2790 INSTRUCTION MANUAL COPYRIGHT © 1992 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED APRIL, 1999. PRINTED IN U.S.A.

  • Page 3: Table Of Contents

    GRINDER CONTROLS GUIDE ...9 OPERATIONS OVERVIEW...10 WIDE KNIVES ...10-11 NARROW KNIVES ...11-12 OTHER BLADES ...12 MAINTENANCE WHEELDRESSING ...13 WHEEL REMOVAL ...13 CLOSURE ...14 MACHINE DATA ...15 WARRANTY AND RETURNS...16 PARTS DIAGRAM ...17 PARTS LIST ...18 Table Of Contents PAGE G2790 Universal Knife Grinder...

  • Page 4: Safety

    Keep work area well lighted. G2790 Universal Knife Grinder Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

  • Page 5: Safety Instructions For Power Tools

    A guard or other part that is damaged should be properly repaired or replaced. 19. NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. G2790 Universal Knife Grinder...

  • Page 6: Additional Safety Instructions For Grinders

    Like all power tools, there is danger associ- ated with the Model G2790 Universal Knife Grinder. Accidents are frequently caused by lack of familiarity or failure to pay atten- tion. Use this tool with respect and caution to lessen the possibility of operator injury.

  • Page 7: Circuit Requirements

    Extension Cords If you find it necessary to use an extension cord with the Model G2790, make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in the standard safety instructions to determine the minimum gauge for the extension cord.

  • Page 8: Introduction

    SECTION 3: INTRODUCTION Commentary We are proud to offer the Grizzly Model G2790 Universal Knife Grinder. The Model G2790 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satis-...

  • Page 9: Unpacking

    A full parts list and breakdown can be found toward the end of this manual. For easier assembly, or to identify missing parts, please refer to the detailed illustrations at the end of the manual. G2790 Universal Knife Grinder ⁄ " - 20 "...

  • Page 10: Clean Up

    Serious personal injury may occur. G2790 Universal Knife Grinder Site Considerations BENCH LOAD Your G2790 Universal Knife Grinder represents a moderately large weight load in a small footprint. Be sure that your workbench is adequately rein- forced to support the weight of the grinder.

  • Page 11: Assembly

    Table Stationary Clamps The Model G2790 features two stationary clamps that can be attached directly to the pivot plate. See Figure 3. The clamps are held in place by compression brackets. To attach the...

  • Page 12: Grinder Controls Guide

    Narrow Knives for further information on the grinding process. Knife Blade Adjuster Slider Assembly Pivot Plate Adjuster Wheel Height Lock ON/OFF Switch G2790 Universal Knife Grinder Knife Blade Clamp Figure 4. Universal Knife Grinder controls. NOTES Grinder Height Handwheel Fence Table Grinding Wheel Work Plate...

  • Page 13: Operations

    Make sure all adjust- ments are done with the machine unplugged. -10- To set up your Model G2790 to handle wide knives: Remove the sliding support from the work plate.

  • Page 14: Narrow Knives

    Failure to exercise care while working near knives could result in severe injury. G2790 Universal Knife Grinder 11. Slowly raise the wheel until it lightly con- tacts the knife bevel. Gently slide the knife across the surface of the grinder. If contact...

  • Page 15: Other Blades

    Planer, jointer and other knives are danger- ously sharp. Use extreme caution, particu- larly after sharpening. Failure to exercise care while working near knives could result in severe injury. G2790 Universal Knife Grinder...

  • Page 16: Maintenance

    Remove the wheel mounting flange. Remove and discard the damaged or worn out wheel and replace with a new wheel. New wheels for the Model G2790 are avail- able through the Grizzly catalog. Check the latest catalog for ordering and price infor- mation.

  • Page 17: Closure

    Washington location using the address in Section 3: Introduction. The specifications, drawings, and photographs illustrated in this manual represent the Model G2790 as supplied when the manual was prepared. However, due to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly.

  • Page 18: Machine Data

    Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G2790 UNIVERSAL KNIFE GRINDER Design Type... Bench Model Overall Dimensions: Height ...13" Length ...24" Width...11 Shipping Weight ...69 lbs. Net Weight ...55 lbs.

  • Page 19: Warranty And Returns

    WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.

  • Page 20: Parts Diagram

    PARTS DIAGRAM G2790 Universal Knife Grinder -17-...

  • Page 21: Parts List

    Table Adj. Screw P2790036 Ball Bearings P2790037 Handwheel PB02 Hex Bolt ” - 20 x P2790039 Socket Cap Screw P2790040 Fence P2790041 Spacer P2790042 Table P2790043 Decal P2790044 Cord Clip PW07 Washer " PWRN01 Wire Nut G2790 Universal Knife Grinder " ”...
  • Page 22 Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Imports to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:_________________________________________________...
  • Page 23 FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...

Table of Contents