Table of Contents
Advertisement
Playing a CD or audio fi le disc
Program playback
Music in a CD or audio fi le disc can be played in the
order programmed by the user.
• Select the CD source and enter stop mode.
1
Select "PGM" (program play mode).
Press [P.MODE].
Each press switches the playback mode.
CD operation
PGM
lit
Program play mode
Normal play mode
Not lit
Audio fi le disc operation
N
lit
Folder play mode
PGM
lit
Program play mode
Normal play mode
Not lit
Display when the program mode is selected for a CD.
2
Select a track/ fi le.
CD operation
Select the track with [G]/[H]
or [Numeric] buttons, and press
[ENTER].
When the 7th track is selected as the fi rst track of the
program.
K-525
Audio fi le disc operation
Select the folder with [G]/[H]
or [Numeric] buttons, and press
[ENTER].
Select an audio fi le with [G]/
[H] or [Numeric] buttons, and
press [ENTER].
Display when fi le 10 in folder 003 is programmed as
the 1st fi le in the program.
If you committed a mistake in selection, press
[CLEAR] on the remote control unit before
pressing [ENTER] and restart selection.
• Up to 32 fi les can be programmed.
3
Start playback.
Press [CDE]/[E].
■
To clear a track/ fi le from the program...
Stop playback and press [CLEAR] on the remote
control unit. Each press clears the last track/ fi le in
the current program.
■
To add a track/ fi le to the program after
programming...
If playback is underway, stop it and perform steps
2 and after.
■
To cancel the program mode...
Stop playback and press [P.MODE] to select the
normal play mode. The program is cleared at this
time.
• The set program is cleared when the input source is
switched, the disc is ejected or the unit is switched
OFF.
20
Playback of Digital Audio Player
Kenwood digital audio player can be connected to
play audio fi les in it.
• For the Kenwood digital audio players models that can be
connected to this unit, see "Handling of D.AUDIO" (page
44).
Playback
1
Connect the player.
Connect a Kenwood digital audio player to the
[D.AUDIO IN] connector using an optional cable or
adapter (page 11).
Also read the instruction manual for the
connected component.
2
Select the "D.AUDIO" input.
Press [D.AUDIOE].
Press [INPUT SELECTOR].
Display when the D.AUDIO input is selected.
3
Turn the connected player ON and
start playing it.
• While the player is connected to this system, the
volume and tone settings on the player are defeated.
If the input level from D.AUDIO seems to be higher
or lower than other input sources when this unit is
set at the same volume level, adjust the input level as
described in "Adjusting the input level" (page 27).
Button operations during
playback/stop
To
Operation
Press [F] during
Stop
playback.
Press
[D.AUDIOE] /
[E] during
Pause
playback.
Press again to
resume playback.
A
Skip a folder
Press [
Press and hold
[G]/[H]/
Fast forward/
[GI]/
fast backward
[JH]
during playback.
Press [H]/
Skip a fi le
[JH].
Press [G]/
Return to
[GI]
previous fi le
successively twice
or more.
Return to the
Press [G]/
beginning of
[GI]
current fi le
once.
• Some control operations may be unavailable depending
on the connected player.
■ Dedicated cable/device for connection
When the Kewnood digital audio player is connected
using the optional Kenwood digital audio player
connection cable, the connected component can be
controlled from this unit or the remote control unit.
For details on the connection and installation, refer to
the instruction manual provided with the connection
cable.
21
B
]
/
[
].
English
Advertisement
Table of Contents
