Refueling; Transporting; Storage; Preparing For Storage - Honda HRR216VXA Owner's Manual

REFUELING

Honda recommends using a spill-proof fuel container (page 17).
This engine is certified to operate on unleaded gasoline with a pump
octane rating of 86 or higher.
Refuel in a well-ventilated area with the engine stopped. If the engine
has been running, allow it to cool first. Never refuel the engine inside a
building where gasoline fumes may reach flames or sparks.
You may use regular unleaded gasoline containing no more than 10%
Ethanol (E10) or 5% Methanol by volume. In addition, Methanol must
contain cosolvents and corrosion inhibitors. Use of fuels with content
of Ethanol or Methanol greater than shown above may cause starting
and/or performance problems. It may also damage metal, rubber, and
plastic parts of the fuel system. Engine damage or performance
problems that result from using a fuel with percentages of Ethanol or
Methanol greater than shown above are not covered by warranty.

WARNING
Gasoline is highly flammable and explosive.
You can be burned or seriously injured when handling fuel.
• Stop the engine and keep heat, sparks, and flame away.
• Handle fuel only outdoors.
• Wipe up spills immediately.
Never use stale or contaminated gasoline or an oil/gasoline mixture.
Avoid getting dirt or water in the fuel tank.
To refuel, remove the fuel tank
cap, and fill the tank with
gasoline to the bottom of the
filler neck. Refuel carefully to
avoid spilling fuel. Do not
overfill. There should be no fuel
in the filler neck.
After refueling, tighten the fuel
tank cap until it clicks.
Move the mower at least 10 feet (3 meters) away from the fueling
source and site before starting the engine.
NOTICE
Fuel can damage paint and plastic. Be careful not to spill fuel when
filling your fuel tank. Damage caused by spilled fuel is not covered by
the DISTRIBUTOR'S LIMITED WARRANTY (page 18).
12
MAXIMUM FUEL LEVEL
FUEL CAP

TRANSPORTING

If the engine has been running, allow it to cool for at least 15 minutes
before loading the mower on the transport vehicle. A hot engine and
exhaust system can burn you and can ignite some materials.
1. Turn the fuel valve to the OFF position (page 6). This will prevent
carburetor flooding and reduce the possibility of fuel leakage.
2. If installed, remove the grass bag.
If a suitable loading ramp is not available, two people should lift the
mower on and off the transport vehicle while holding the mower level.
Position the mower so all four wheels are on the bed of the transport
vehicle. Tie the mower down with rope or straps, and block the
wheels. Keep the tie-down rope or straps away from the controls,
adjustment levers, cables, and the carburetor.
The handlebar can be folded so the mower will take up less space
(page 13).

STORAGE

PREPARING FOR STORAGE

Proper storage preparation is essential for keeping your lawn mower
trouble free and looking good. The following steps will help to keep
rust and corrosion from impairing your lawn mower's function and
appearance, and will make the engine easier to start when you use
the lawn mower again.
Cleaning
Engine
Wash the engine by hand, and be careful to prevent water from
entering the air cleaner.
NOTICE
Using a garden hose or pressure washing equipment can force water
into the air cleaner. Water in the air cleaner will soak the paper
element and can enter the carburetor or engine cylinder, causing
damage.
Water contacting a hot engine can cause damage. If the engine has
been running, allow it to cool for at least half an hour before washing.
Mower Deck
Wash the lawn mower, including the underside of the mower deck.
If using a garden hose or pressure washing equipment to clean the
mower deck, be careful to avoid getting water into controls and
cables, or anywhere near the engine air cleaner or muffler opening.
Before washing the underside of the mower deck, be sure the fuel
valve is in the OFF position. Disconnect the spark plug cap. Rest the
mower on its right side, so the air cleaner side is up. This will help to
prevent fuel leakage and hard starting due to carburetor flooding.
Wear heavy gloves to protect your hands from the blades.
Grass Bag
Remove the bag from the mower, and wash it with a garden hose or
pressure washing equipment. Allow the bag to dry completely before
storage.