Connection Scheme; Connecting To Steering Wheel Remote Controller; External Amplifiers And Subwoofer - JVC KW-AVX836 Instructions Manual

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1
Connect the colored leads of the power cord in the order specified in the illustration below.
2
Connect the antenna cord.
3
Finally connect the wiring harness to the unit.
• The terminals and cables of all models are shown in the illustration for the purpose of explanation.
*
MIC IN 1
*
1
Antenna
terminal
Rear ground Fan
terminal
2
Only for KW-AVX836/KW-AVX835:
Insert the Bluetooth adapter KS-UBT1 on the
front of the unit. See diagram
White with black stripe
A
Connecting to the steering wheel remote controller
If your car is equipped with the steering wheel remote controller, you can operate this unit using the
controller. For connection, an exclusive remote adapter (not supplied) which matches your car is
required. For details, consult the same car audio dealer as where the unit is purchased.
KW-AVX836/KW-AVX835
KW-AVX736/KW-AVX735
B
Connecting the external amplifiers and subwoofer
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, and connect them to the amplifier. Leave the
speaker leads of this unit unused.
• You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to
get clear sounds and to prevent internal heat built-up inside the unit.
See page 30 of the INSTRUCTIONS.
To the remote lead of other equipment
*
2
Y-connector
Remote lead
Remote lead (blue
Rear
with white stripe)
speakers
*
4
JVC
Amplifier
*
5
E
Connecting the microphone (Only for KW-AVX836/KW-AVX835)
1 2
Microphone
Microphone
holder
MIC IN
KW-AVX836
Adhesive tape
KW-AVX835
Inserting the Bluetooth adapter (Only for KW-AVX836/KW-AVX835)
1 2
Turn on the power Insert the Bluetooth
then open the monitor adapter with the JVC logo
panel (see page 6 of the facing upside.
INSTRUCTIONS).
(see page 1)
REVERSE
GEAR
SIGNAL
SUBWOOFER OUT
15 A fuse
‰ below.
9
White Gray with black stripe
Left speaker
(front)
Steering wheel remote controller (equipped in the car)
OE remote adapter * 2
*
4
*
2
*
4
KW-AVX836/KW-AVX835
KW-AVX736/KW-AVX735
or
Secure the microphone cord using cord cramps (not supplied) if necessary.
Bluetooth adapter
(KS-UBT1)
3
Black
1
To metallic body or chassis of the car
(GND)
Yellow * 3
2
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
Red
3
Blue
(POWER ANTENNA)
Blue with white stripe
Orange with white stripe
(ILLUMINATION CONTROL)
Brown
(TEL MUTING)
Light green
(PARKING BRAKE)
Gray Green with black stripe
Right speaker
(front)
C
Connecting an external navigation box
Connect an external navigation box to the RGB input terminal.
The positional information detected on the touch panel and picture signals from the navigation box are
transferred through the terminal.
Refer to the manual of the external
navigation box for details.
• Please contact your dealer to inquire about
compatible navigation boxes.
• JVC cannot guarantee proper operation of the external devices connected to the RGB input terminal.
D
Connecting the external components
Camcorder
etc.
USB devices
JVC Amplifier
*
5
Subwoofer
USB cable (approx. 1.2 m)
Front
KW-AVX836
speakers
KW-AVX835
KW-AVX736
JVC KW-AVX735
Amplifier
*
5
– To watch the video: USB Audio and Video cable for iPod/iPhone—KS-U30 (not supplied) *
– To listen to the music: USB 2.0 cable (accessory of the iPod/iPhone)
We recommend to attach the
microphone near the steering
wheel using the microphone
holder.
Microphone clip
3
Close the monitor panel.
(Press)
2
1
*
2
*
2
To an accessory terminal in the fuse block
4
To automatic antenna is any (250 mA max.)
5
To the remote lead of other equipment (200 mA max.)
6
To car light control switch
7
To mobile phone system
To parking brake (see page 1)
8
Crimp connector
Green Purple with black stripe
Left speaker
(rear)
External
navigation
2
box*
RGB input terminal
*
6
*
4
KW-AVX836/KW-AVX835
KW-AVX736/KW-AVX735
Connecting the iPod or the iPhone
USB 2.0 cable (accessory of the
USB device
KW-AVX836/KW-AVX835
KW-AVX736/KW-AVX735
* 1
Only for KW-AVX836/KW-AVX835.
* 2
Not supplied for this unit.
* 3
Before checking the operation of this unit prior to installation, this lead
must be connected, otherwise power cannot be turned on.
Do not connect the lead directly to the battery.
* 4
Audio cord (not supplied for this unit).
* 5
Firmly attach the ground wire to the metallic body or to the chassis of
the car—to the place uncoated with paint (if coated with paint, remove
the paint before attaching the wire). Failure to do so may cause damage
to the unit.
* 6
Video cord (not supplied for this unit).
* 7
When using the cable, you need to change the setting on the unit (see
page 19 of the INSTRUCTIONS).
• iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
• iPhone is a trademark of Apple Inc.
See each diagram below.
Ignition switch
Fuse block
Purple
Right speaker
(rear)
KW-AVX836/KW-AVX835
KW-AVX736/KW-AVX735
2
KV-CM1*
Rear view camera
*
6
External
monitor
*
4
*
1
iPod/iPhone)
KS-U30
(not supplied)
7