Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for QSC AcousticDesign S8T
Summary of Contents for QSC AcousticDesign S8T
-
Page 1: User Guide
AcousticDesign™ Series User Guide S8T – 8" two-way, foreground/background loudspeaker with 70/100V transformer S10T – 10" two-way, foreground/background loudspeaker with 70/100V transformer S12 – 12" two-way, foreground/background loudspeaker TD-000329-01-A TD-000329-01... -
Page 2: Explanation Of Symbols
EXPLANATION OF SYMBOLS The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death. The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result in damage to the equipment that may not be covered under the warranty. -
Page 3: Package Contents
Damage to, or loss of any software or data residing on the product is not covered. When providing repair or replacement service, QSC will use reasonable efforts to reinstall the product’s original software confi... - Page 4 WARNING!: Install the system in accordance with local building codes and regulations. Use a licensed contractor or professional engineer. QSC Audio Products is not responsible for damages resulting from the negligent installation of any bracket or loudspeaker. 1. Mount to a surface capable of supporting the weight of the loudspeaker.
- Page 5 Adjust the Angle of the X-Mount™ Bracket Refer to Figure 5 NOTE: This step may be done now or after mounting the loudspeaker. 1. Use a 5mm hex wrench to loosen the adjustment locking screws. 2. Orient the bracket as necessary. -15°/+30°...
- Page 6 The AcousticDesign loudspeakers (models S8T, S10T and S12) may be suspended using the pull-back point and M10 eyebolts you install at the bottom of the enclosures. NOTE: Suspending the enclosure woofer side up positions the HF closer to the listener and helps improve bass response when coupled against the ceiling and wall planes.
- Page 7 Install the Weather Cover (Optional) Refer to Figure 8 1. Slide the nut (1), compression gasket (2), and weather cover / gasket (3) over the wiring for the loudspeaker. 2. Terminate the wiring to the Euro-style connector, refer to "Wire the Loudspeaker" on page 7 3.
- Page 8 S12 Dimensions 354 mm (13.9 in) 354 mm (13.9 in) 323 mm (12.7 in) — Figure 10 — TD-000329-01-A...
- Page 9 S10T Dimensions 318 mm (12.5 in) 318 mm (12.5 in) 298 mm (11.7 in) — Figure 11 — TD-000329-01-A...
- Page 10 8T Dimensions 254 mm (10 in) 254 mm (10 in) 254 mm (10 in) — Figure 12 — TD-000329-01-A...
-
Page 11: Specifications
The AD Series loudspeakers qualifi ed for outdoor use using the following tests Salt fog: MIL-STD-810G Method 509.5 for 100 hrs. Humidity: MIL-STD-810G Method 507.5, Natural cycle B2, cyclic high RH for 7 days High and low temperature: tested according to QSC internal standards between -20° and 50° C Dimensions (HWD) millimeters... - Page 12 © 2013 QSC Audio Products, LLC. All rights reserved. QSC and the QSC logo are registered trademarks of QSC Audio Products, LLC in the U.S. and other countries. X-Mount is a trademark of QSC Audio Products, LLC. All other trademarks are the property of their respective owners. U.S. and international patents pending.