Advertisement
Advertisement
Table of Contents
Summary of Contents for Harbinger HA120
- Page 1 HA120 Owner’s Manual 4-Channel 120-Watt PA System www.harbingerproaudio.com...
- Page 3 Congratulations on your purchase of Harbinger’s HA120 4-Channel 120-Watt PA System. Built with rugged, carpet-covered 4 CHANNEL wood enclosures, the HA120 is the ideal choice for musicians looking for a PA that delivers great sound night after night. MI D...
-
Page 4: Important Safety Instructions
HA120 Important Safety Instructions dAnGeR IMPORTAnT SAfeTY InSTRUCTIOnS Exposure to extremely high noise levels may cause 1. Read all safety and operating instructions before using permanent hearing loss. Individuals vary considerably this product. to noise-induced hearing loss but most will lose some 2. -
Page 5: Input Channels
Owner’s Manual Input Channels 1 lOW eQ 4 fX Send This shelving control gives 15dB of boost or cut at 80Hz This level control sets the amount of signal that will be and below. Add warmth to vocals or extra punch to sent to the built-in digital delay effect. -
Page 6: Master Section
HA120 Master Section 1. MASTeR eQ 3. POWeR IndICATOR When the power switch at the rear panel is turned on, lOW: This shelving control gives 15dB of boost or cut this indicator will illuminate. at 80Hz and below. 4. AUX In COnTROl... -
Page 7: Rear Panel
Connect both speakers to these jacks. The minimum and the external signal is returned on the RING. An impedance load is 4 Ω. Do not connect more than two 8 HA120 unbalanced 1/4” insert cable is required to connect to Ω speakers or damage may occur. -
Page 8: General Application
HA120 General Application MAI N I N SE RT (Input) HA120 FUSE :2A AC 1 20V~50/60HZ 200W FUSE 250V WITH ONLY SPE AKE R O U T HA120 120 WATT 4 CHANNEL MIXER MI D DIGITAL DELAY PEAK PEAK PEAK... - Page 9 Owner’s Manual General Application (Output) MAI N I N SE RT HA120 FUSE :2A AC 1 20V~50/60HZ 200W FUSE 250V WITH ONLY SPE AKE R O U T CAUTION: Minimum 4Ω load. Use a maximum of two 8Ω speakers. MI D...
- Page 10 HA120 Power Amp Specifications POWeR AMP fReQUenCY ReSPOnSe (MIC InPUT TO OUTPUT) Max Output Power: 120 Watts (@ 4Ω) 20Hz to 20kHz line level output @+4dBu into 600Ω +1/–3dB 88 Watts (@ 8Ω) 20Hz to 20kHz power amp output- 1 watt into 8Ω +1/–3dB...
-
Page 11: Speaker Specifications
Owner’s Manual Speaker Specifications RMS POWeR HAndlInG CROSSOVeR 80W / 8Ω 3.8K / -12dB per octave fReQUenCY ReSPOnSe PeAK POWeR HAndlInG 40Hz–20kHz 110W / 8Ω MAX SPl IMPedAnCe lOAd 116dB 8Ω dIMenSIOnS Of SPeAKeR BOX HORn COnSTRUCTIOn H 23.2” x W 14.4” x D 12.8” Compression Driver neT WeIGHT WOOfeR COnSTRUCTIOn:... -
Page 12: Warranty
If your covered product is defective, return the defective system to your reseller for in-store exchange, or contact support@ harbingerproaudio.com. If you are uncertain which component is defective, or to obtain instructions for removing a component, please contact Harbinger Support Headquarters at the above e-mail address for assistance or visit our website at www.harbingerproaudio.com.