Page 3
Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable.
The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instructions for an operation Hints and Tips Environmental information MANUFACTURER: MANUFACTURER: MANUFACTURER: MANUFACTURER: MANUFACTURER: ELECTROLUX ITALIA S.p.A. C.so Lino Zanussi, 30 33080 PORCIA (PN)- Italy...
5 Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950. Installation This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations.
Page 6
6 electrolux When using the hob for a long period time, the ventilation should be improved, by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water. Do not operate the hob with wet hands.
8 electrolux Operation Hob burners control knobs The symbols on the knobs mean that : there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support.
Page 9
9 If the control knobs become difficult to turn, please contact your local Service Force Centre. Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a flat bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table below).
10 electrolux Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
11 The Burners The burner caps and crowns can be removed for cleaning. Wash the burners caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove.
12 electrolux Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM SYMPTOM SYMPTOM SYMPTOM SYMPTOM SOLUTION SOLUTION SOLUTION SOLUTION SOLUTION There is no spark when Check that the unit is plugged lighting the gas.
13 Instructions for the Installer Engineer technical data Engineer technical data Engineer technical data Engineer technical data Engineer technical data OVERALL DIMENSIONS OVERALL DIMENSIONS OVERALL DIMENSIONS Width: 580 mm OVERALL DIMENSIONS OVERALL DIMENSIONS Depth: 500 mm CUT OUT DIMENSIONS...
Page 14
14 electrolux Characteristics of gas burners Characteristics of gas burners Characteristics of gas burners Characteristics of gas burners Characteristics of gas burners BURNER RAPID SEMI-RAPID AUXILIARY (large) (medium) (small) TYPE OF Characteristics POSITION NOMINAL THERMAL 0.75 0.45 0.33 NATURAL POWER (kW) NOMINAL FLOW 0.286...
15 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S.
16 electrolux Installation IMPORTANT Any gas installation must be carried out by a GAS SAFE Any gas installation must be carried out by a GAS SAFE Any gas installation must be carried out by a GAS SAFE Any gas installation must be carried out by a GAS SAFE...
17 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation.
18 electrolux Fitting the Hob into the Worktop Carry out the building in of the hob as follows: 1) put the seals supplied with the hob, on the edges of the cut out, taking care that the seals meet without overlapping;...
19 Building In B B B B B uilding over a cupboard or drawer uilding over a cupboard or drawer uilding over a cupboard or drawer uilding over a cupboard or drawer uilding over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface.
20 electrolux Electrical Connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.
21 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations.
22 electrolux Fault Finding Preliminary Electrical Systems Check Preliminary Electrical Systems Check Preliminary Electrical Systems Check Preliminary Electrical Systems Check Preliminary Electrical Systems Check Blue Brown Green Yellow S T A R T S T A R T S T A R T...
Page 23
23 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight.
Page 24
24 electrolux Ignition System / Gas Ignition Ignition System / Gas Ignition Ignition System / Gas Ignition Ignition System / Gas Ignition Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse and...
25 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
26 electrolux Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion from natural gas to LPG should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted.
Page 27
27 Standard Guarantee Conditions We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: •The appliance has been correctly installed and used only on the gas and electricity...
Page 28
Customer Care Customer Care Customer Care For general enquiries concerning your Electrolux appliance, or for further information on Electrolux products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www www.electr...
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home, i.e. is not used for commercial purposes. • The appliance is installed in accordance with all relevant regulations in force within your new country of residence.