Electrolux EFC 70700 User Manual page 16

Installation Installation
Installation Installation Installation
Make sure that the cooker hood is disconnected from the power Make sure that the cooker hood is disconnected from the power
Make sure that the cooker hood is disconnected from the power Make sure that the cooker hood is disconnected from the power Make sure that the cooker hood is disconnected from the power
supply before carrying out the installation. supply before carrying out the installation.
supply before carrying out the installation. supply before carrying out the installation. supply before carrying out the installation.
• Mark the wall with a centre line, this will aid mounting procedure (1)
the template so that the mid line printed on the template matches with the
centre line previously drawn, the lower side of the template corresponds to the
lower side of the hood once mounted (2)
• Drill four holes Ø 8mm and fit four wall plugs (3)
• Drill two holes Ø 8mm on the upper side close to the ceilling (4 (4 (4 (4 (4) use the
chimney support as a template, check that the mid of the chimney support
corresponds to the mid of the centre line previously drawn, fit two wall plugs.
Note: Note: ONL Note: ONL ONL ONLY Y Y Y Y in case the hood is to be used in filter version
Note: Note: ONL
deflector E E E E E on the chimney support and the connection flange G G G G G with two
screws each (5). (5). (5). (5). (5).
• Put the chimney support close to the ceiling to the vertical of the cooking
place, use the centre line (1)
and drill, then insert two wall plugs and fix the chimney support with two
screws and washers (6)
• Screw two screws (do not tighten completely, leave them so that can be used
to hang the hood), hang the hood (7)
definitively with two screws and washers (8),
securely tightened.
• Fit an exhaust pipe (9)
connection flange G G G G G of the deflector E E E E E (Filter version) or to the outside (Extractor
version).
• Make electrical connection (10)
mains supply.
• Place the cable clamp in the corresponding housing (11)
• Fix the control panel to the rear bracket on the lower section of the chimney
with two screws (12
position of control switches).
• Position the chimney and secure them in place, first up (13a)
support (13b) (13b) (13b) (13b) (13b) .
• Then slide the chimney downwards making sure the cable clamp (step 11)
seated in the housing on chimeny (14)
• Fix the lower section of the chimney with two screws from the inside of the
hood (15) (15) (15) (15).
(15)
• Refit the grease filters, connect the hood and the home general electric panel
and check if the hood works properly.
(1) (1) for easy positioning, mark two holes onto the wall (1) (1)
(6) (6). (6) (6)
(7) (7) (7) (7), remove the grease filters and fix it
(9) (9) to connect the outlet hole D D D D D of the hood to the (9) (9)
(10) (10), but leave the hood disconnected from the (10)
(10)
12 12 - Cable must be positioned upwards to have correct 12
12
(14) (14)
(14). (14)
(2) (2). (2) (2)
(3) (3). (3) (3)
filter version filter version, mount the filter version
filter version
(8), (8),
(8), (8), check that all four screws are
(11) (11)
(11). (11)
electrolux electrolux electrolux installation electrolux electrolux
(1) (1), position (1) (1)
(13a) (13a)
(13a) (13a) to the chimney
(step 11) is (step 11) (step 11)
(step 11)
17 17 17 17 17
GB