HUSTLER MINI Z 36 Owner's Manual

Tractor and deck
Hide thumbs Also See for MINI Z 36:

Advertisement

This manual applies to the following Hustler equipment lines:
Hustler Mini Z 36/42
To the new owner
The purpose of this manual is to assist owners and operators in
maintaining and operating the Hustler Mini Z tractor and deck. Please read
it carefully; information and instructions furnished can help you achieve
years of dependable performance.
A separate Engine Owner's Manual is included with your owner's
packet which contains additional engine information that will not be
repeated in this manual. You are urged to read it before attempting any
operation or repair of the engine.
The Quick Reference Decals are designed to give the operator brief
information needed in the daily operation and service of the machine.
These decals are not intended to be used in place of this manual but instead
is to be used as an extension of this manual. These decals should not be
removed or obliterated. Replace these decals if they become unreadable.
It is the owner's responsibility to make certain that the operator reads
and understands this manual and all decals before operating this machine.
It is also the owner's responsibility to make certain that the operator is a
qualified and physically able individual, properly trained in the operation of
this equipment. Local regulations may restrict the age of the operator.
IMPORTANT: For more detailed maintenance and adjustment
information refer to the proper parts manual for your machine. Refer to
the Product Literature section of this manual for ordering information.
Using this manual
General operation, adjustment and maintenance guidance is outlined for
both the experienced and novice Hustler user. Operating conditions vary
considerably and cannot all be addressed individually. Through
experience, however, operators should find no difficulty in developing
good operating skills suitable to most conditions.
Directions used in this manual, for example RIGHT or LEFT, refer to
directions when seated on tractor facing forward, unless otherwise stated.
Photographs and illustrations used were current at the time of printing,
but subsequent production changes may cause your machine to vary
slightly in detail. Hustler Turf Equipment reserves the right to redesign and
change the machine as deemed necessary, without notification. If a change
has been made to your machine which is not reflected in this owner's
manual, or the parts manual, see your Hustler dealer for current information
and parts.
IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of California Public Resource Code Section 4442 to use or
operate this engine on any forest-covered, brush-covered, or grass-covered unimproved land. Other states or federal areas may have similar laws.
This spark ignition system complies with Canadian ICES-002.
The enclosed Engine Owner's Manual is supplied for information regarding the U.S. Environmental Protection Agency (EPA) and the California
Emission Control Regulation of emission systems, maintenance and warranty.
Keep this Engine Owner's Manual with your unit. Should the Engine Owner's Manual become damaged or illegible, replace immediately.
Replacements may be ordered per the information found in the Product Information section of this manual.
107708_0306

GENERAL INFORMATION

WARNING:
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
1
Warranty registration
The Delivery and Warranty Registration form must be completed and
signed to validate your warranty protection. As the new equipment owner,
you are expected to see that the form is completed and forwarded to Hustler
Turf Equipment at time of delivery.
Be sure to register the tractor plus each attachment that displays a model
and serial identification number plate with Hustler Turf Equipment.
IMPORTANT: Any unauthorized modification, alteration, or use of
non-approved attachments voids the warranty and releases Hustler Turf
Equipment from any liability arising from subsequent use of this
equipment.
Model and serial number
Tractor model and serial numbers are found on the serial identification
plate, located on the frame directly below and to the right of the operator's
platform.
These numbers are required on the Warranty Registration form. They
will also assure you of the correct service parts when replacement becomes
necessary.
Parts and service
Use original Hustler replacement parts only. These parts are available
through your local Hustler dealer. To obtain prompt, efficient service,
always provide the following information when ordering parts:
1. Correct part description
2. Correct model number.
3. Correct serial number.
All warranty repair and service must be handled through an authorized
Hustler dealer. Arrangements should be made through your local service
center.

Advertisement

Table of Contents
loading

Summary of Contents for HUSTLER MINI Z 36

  • Page 1: General Information

    The Delivery and Warranty Registration form must be completed and Hustler Mini Z 36/42 signed to validate your warranty protection. As the new equipment owner, you are expected to see that the form is completed and forwarded to Hustler To the new owner Turf Equipment at time of delivery.
  • Page 2 107708_0306...
  • Page 3 Rental Units (90 days): Within 90 days of date of delivery Hustler ● Repairs or replacement as the result if any alterations or Turf Equipment, provides a limited warranty on all materials and modifications, in the determination of Hustler Turf Equipment, workmanship for units used for rental purposes.
  • Page 4: Warranty Registration

    Any operator must be cautious and ● Cost of any substitute equipment, facilities, services or downtime keep safety in mind at all times. Any operator, prior to using the Hustler ● The claims of third parties including customers, and injury to...
  • Page 5: Safety Precautions

    SAFETY PRECAUTIONS The Quick Reference Decals are designed to give the operator brief information needed in the daily operation and service of the machine. These decals are not intended to be used in place of this manual but instead is to be used as an extension of this manual. These decals should not be removed or obliterated.
  • Page 6: Safety And Instruction Decals

    Part Number involve your Hustler dealer to resolve the problem before continuing to operate. If pump belt fails, steering control will be lost. Refer to owner’s manual for Hydrogen gas forms inside the battery.
  • Page 7: Slope Guide

    SLOPE GUIDE Use this diagram when determining the degree of slope to be mowed. E (15 Slope Guide Lines D (10 C (5 Line A 1. Hold this sheet of paper in front of you. Make sure that line A is horizontal. 2.
  • Page 8 107708_0306...
  • Page 9: Safe Operating Practices

    OPERATION Safe Operating Practices running. Turn off the engine and be sure the blades have stopped This product is capable of amputating hands and feet and throwing before cleaning. Use a stick to clear a plugged discharge area. objects. Always follow all safety instructions to avoid serious injury or Never use your hand! death.
  • Page 10: Control Panel

    These are just a few examples of situations when caution must be injury. ▲ The Hustler mower is capable of operating horizontally (traverse) on used when operating on a slope. There are many other possibilities moderately steep slopes. When operating on slopes up to 15 too numerous to mention.
  • Page 11: Safety Start Interlock System

    (is not opening or closing) and if the cause can not be determined, replace the seat switch. If the problem can not be located, contact your Hustler Dealer. WARNING: The safety interlock system should always function per steps 4 and 5. If it does not function properly, it should be corrected immediately.
  • Page 12: Driving The Tractor

    Inspect the machine and Do not tow the machine. Move it by hand or use a winch to load on a involve your Hustler dealer to resolve the problem before trailer for transporting. continuing to operate.
  • Page 13 FRONT OF TRACTOR FACES THIS DIRECTION FORWARD TRAVEL PIVOT TURN FORWARD TRAVEL REVERSE TRAVEL REVERSE TRAVEL RIGHT TURN RIGHT TURN N = Neutral Position Direction of arrows indicate direction of tractor movement. Figure 3-6 familiar with these characteristics before attempting normal speed the cutting height that was used in the past.
  • Page 14: Mower Deck Operation

    Mower deck operation Three point turn DANGER: Never attempt to make any adjustments to the mower deck while the engine is running or with the deck drive clutch engaged. Mower blades cannot be seen and are located very close to deck housing. Fingers and toes can be cut off instantly.
  • Page 15: Anti-Scalp Wheels

    Anti-scalp wheels Anti-scalp wheel kits are standard on Hustler Mid Mount Z units. These anti-scalp wheels are designed to minimize scalping when mowing on rough uneven terrain. After setting the cutting height, adjust the anti-scalp wheels so they extend below the deck but do not contact the ground. They should always be at least 1/4”...
  • Page 17: Safe Servicing Practices

    ▲ Unless specifically required, DO NOT have engine running when caution when servicing them. servicing or making adjustments to tractor. Place control levers in ▲ Use only genuine Hustler replacement parts to ensure that original the park brake position, disengage deck clutch, remove ignition standards are maintained switch key and disconnect negative battery cable before doing any maintenance.
  • Page 18: Electrical System

    Always connect the positive (red) battery cable before connecting the negative (black) cable. Hydraulic system The Hustler Mini Z 36/42 is equipped with two Hydro-Gear ZT 2800 transaxles. Fig. 4-1 IMPORTANT: Never use hydraulic or automatic transmission fluid in Filter this system;...
  • Page 19: Fuel System

    Fuel shut-off valve filter. Each transaxle’s filter is located per Fig. 4-3. A standard oil filter wrench is used to change filter, threads are right handed. Use a Hustler approved filter element only. IMPORTANT: Purging procedure must be followed after changing the...
  • Page 20: General Engine Maintenance

    (Replace) Cutting Plane Inspect the machine and involve your Hustler dealer to resolve the problem before continuing to operate. Cutting Edge Inspect the belt pulley grooves and flanges for wear. A new belt, or one in good condition, should never run against the bottom of the groove.
  • Page 21: Seat Adjustment

    Use a 15/16" wrench to remove the 5/8" cap screw holding the blade to the spindle shaft from underneath. NOTE: A blade holding tool (part number 381442) is available from Hustler Turf Equipment. It is designed to prevent the blades from rotating when they are being removed or installed on the spindle.
  • Page 22: Hustler Mini Z 36/42 Maintenance Schedule

    Hustler Mini Z 36/42 Maintenance Schedule Refer to Fig. 4-11 WEEKLY MONTHLY ANNUALLY OR SERVICE AT OR 50 OR 100 INTERVALS INDICATED HOURS HOURS HOURS Verify safety start interlock system Daily Visually inspect unit for loose hardware and/or damaged parts...
  • Page 23 Hustler Mini Z 36/42 Maintenance Locator Chart 1. Engine Oil Fill & Dipstick 2. Fuel Filter 3. Engine Air Cleaner 4. Engine Oil Drain Plug 5. Battery 6. Fuel Tanks 7. Gauge Wheel Bearing Zerks (2) 8. Engine Oil Filter 9.
  • Page 24: Troubleshooting

    Hustler Mini Z 36/42 TROUBLESHOOTING The majority of operating problems that occur with a system can be traced to improper adjustments or delayed service. A consistently applied preventative maintenance program, as outlined in the maintenance section of this manual, will prevent many problems. The following chart is designed to help you locate a problem by suggesting probable causes and the recommended solutions.
  • Page 25: Product Literature

    1. Remove all grass, dirt, and trash from tractor and mower. Clean engine flooding and loss of power. tractor and mower and touch up all scrapes with Hustler spray paint. 5. Remove and replace fuel filter per maintenance schedule. IMPORTANT: Wash the machine with a mild detergent and water.
  • Page 26 107708_0306...
  • Page 27: Table Of Contents

    Safety precautions ................5 Engine starting ................11 Safety start interlock system ............11 Hustler Mini Z 36/42 troubleshooting..........25 Seat adjustment ................21 Hustler Mini Z 36/42 maintenance locator chart ......23 Slope guide..................7 Hustler Mini Z 36/42 maintenance schedule .......22 Stopping the engine..............12 Fuel system ..................19 Storage..................25...
  • Page 28 107708_0306...

This manual is also suitable for:

Mini z 42

Table of Contents