Table of Contents
Advertisement
4 .
4 .
4 .
4 . 4 .
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] ,
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] ,
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] ,
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] ,
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] ,
S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] )
S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] )
S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] )
S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] )
S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0 or
RAID 1 configuration with the Intel
through the onboard Intel
for details on how to set up Serial RAID configurations.
These connectors are set to S t a n d a r d I D E
S S S S S t a n d a r d I D E
t a n d a r d I D E
t a n d a r d I D E
t a n d a r d I D E
t a n d a r d I D E mode, you can connect Serial ATA boot/data hard disk
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the C o n f i g u r e S A T A A s
to [RAID]. See section "4.3.6 IDE Configuration" on page 4-15 for details.
P5AD2 Deluxe SATA connectors
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
•
•
•
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 3 / S A T A 4
S A T A 3 / S A T A 4
S A T A 3 / S A T A 4
S A T A 3 / S A T A 4
S A T A 3 / S A T A 4
2 - 2 4
2 - 2 4
2 - 2 4
2 - 2 4
2 - 2 4
®
P5AD2
You must install Windows
Service Pack 1 before using Serial ATA hard disk drives. The Serial
ATA RAID feature (RAID 0/RAID 1) is available only if you are using
Windows
®
2000/XP.
Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
When using the connectors in S S S S S t a n d a r d I D E
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
C o l o r
C o l o r
C o l o r
C o l o r
C o l o r
R e d
R e d
R e d
R e d
R e d
B l a c k
B l a c k
B l a c k
B l a c k
B l a c k
®
Matrix Storage Technology
ICH6R RAID controller. Refer to Chapter 5
S t a n d a r d I D E
S t a n d a r d I D E mode by default. In
S t a n d a r d I D E
S t a n d a r d I D E
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s item in the BIOS
SATA3
SATA1
®
2000 Service Pack 4 or the Windows
t a n d a r d I D E
t a n d a r d I D E
t a n d a r d I D E mode, connect the
t a n d a r d I D E
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
M a s t e r
M a s t e r
M a s t e r
M a s t e r
M a s t e r
S l a v e
S l a v e
S l a v e
S l a v e
S l a v e
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
SATA4
SATA2
®
U s e
U s e
U s e
U s e
U s e
B o o t d i s k
B o o t d i s k
B o o t d i s k
B o o t d i s k
B o o t d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
XP
Advertisement
Table of Contents
