Generac Power Systems 005221-0 Owner's Manual page 47

1 033212 4
2 075580 1
3 0F6390 1
4 039253 2
5 022145 2
6 022129 6
7 045771 2
9 0E8286 1
10 026812 2
11 0F8379 1
12 0F3869 1 (REF.)
13 057823 2
14 059194 1
15 064945 1
16 0D1509 1
17 * 050279 1
050280 1
18 0E7839 1
19 0E6586 1
20 0E4394 1
21 040105 1
22 0E6382B 1 (REF)
23 0E7121 1 (REF)
24 0E6376B 1 (REF)
25 042561 2
26 0E9295 1
27 061012 1
28 022097 4
29 044118 1
30 046580 4
31 026915 2
33 0F6155 1
SCREW HHC 5/16-18 X 1-1/4 G5
FLANGE FUEL INLET
REGULATOR ASSEMBLY DUAL FUEL
SCREW HHC M8-1.25 X 20 G8.8
WASHER FLAT 5/16-M8 ZINC
WASHER LOCK M8-5/16
NUT HEX M8-1.25 G8 CLEAR ZINC
STREET EL 45 DEG 1/2" NPT BRASS
ELBOW 90D 3/4 NPT
NIPPLE PIPE 3/4 NPT X 7"
SWITCH PRESSURE GAS 5" RISE (INCLUDED WITH I/N 3)
CLAMP HOSE #10 .56-1.06
HOSE 5/8 ID LPG & NG (31.5" LG)
GASKET CARB ADAPTOR
DECAL INLET PRESSURE
DECAL FUEL INLET NG (NATURAL GAS APPLICATION)
DECAL FUEL INLET LPG (LP VAPOR APPLICATION)
MACHINING CARBURETOR ADAPTOR
GASKET BOSCH 32 & 40
ACTUATOR BOSCH 40 GOVERNOR
HOSE COOL 2IN ID 20R4 (2" LG)
VENTURI HOLDER W/40MM ACTUATOR
O-RING 47.625 ID X 2.38 WIDTH
VENTURI 28 ID THROTTLE W/CHOKE
CLAMP HOSE #36 1.88-2.75
ASSY THROTTLE 28MM
PLUG STD PIPE 1/8 SOCKET HEAD
WASHER LOCK M6-1/4
BARBED STR 1/2 NPT X 5/8
SCREW SHC M6-1.0 X 45 G12.9
NIPPLE CLOSE 3/4 X 1.375
HARNESS CPL FUEL JUMPER
NOTES:
1. REGULATOR (I/N 3) AS SHOWN IN ILLUSTRATION IS SET UP FOR
NATURAL GAS APPLICATION.
2. TO CONFIGURE REGULATOR FOR LP VAPOR, SWITCH HOSE BARB,
HOSE CLAMP (I/N 13) AND HOSE (I/N 14) FROM "OUT-1" TO "OUT-2".
REPLACE PIPE PLUG FROM "OUT-2" TO "OUT-1". USE PIPE SEALANT
ON HOSE BARB AND PIPE PLUG. MAKE SURE TO KEEP PORTS FREE
FROM DEBRIS DURING RECONFIGURATION PROCESS.
3*. FOR LP VAPOR APPLICATION SUBSTITUE LPG FUEL INLET DECAL P/N
050280 FOR NG FUEL INLET DECAL P/N 050279 (ITEM17).
4 . WHEN SWITCHING FUEL TYPES, THE PROPER DIP SWITCH SITTINGS
MUST BE MADE TO THE CONTROL PANEL. SEE OWNERS MANUAL, FUEL
SECTION FOR MORE DETAILS.