Installation; Built-In Model; Electrical Connections - Electrolux EMS2487 User Manual

EMS 2487

Installation

• When you unpack the oven, check
that the product is free from damage.
Damage or any missing parts must be
reported immediately to the retailer.
The oven, parts of the oven or the
accessories may be wrapped by a pro-
tection foil. If so, you must remove this
foil before using the oven. Do not leave
packing material so that small children
can play with it. This can be hazardous.
• Do not use your appliance immediately
(wait approx. 1-2 hours) after transfer
from a cold place to a warm place as
condensation may cause a malfunction.
• This oven can be used as a free stan-
ding oven or built-in using the kit avail-
able with the oven. To install the oven in
a kitchen cabinet follow the instructions
supplied with the building-in kit. The
oven should be in-stalled on a flat, level
surface at least 85 cm above floor level.
The surface must be strong enough to
safely bear the weight (19 kg) of the oven,
and the contents. To avoid the possibility
of causing vibration or noise, the oven
must be in a stable position.
• Be sure to install the oven away from
heat and water sources.
• Do not block air vents on the top and
the sides of the cabinet nor place any
articles on the top of the oven. A gap all
around the oven is necessary : 14 cm
above the oven and any objects, 5 cm
on the
14 cm
sides and
10 cm
b e h i n d
the oven.
5 cm
If air vents 5 cm
are blocked during operation, the oven
may overheat, and this may lead to
malfunctioning.
• This oven does conform to EEC
requirements* of radio interference
suppression, but some interference
may occur if it is placed too close to a
radio or TV, so keep them as far apart
as possible.

Built-in model

• To install the appliance in a kitchen
cabinet, use the appropriate mounting
frame, kit number EBR/BF 246. When
building into a high cabinet, you may
use the liftdoor. Note the relevant infor-
mation for installation and connection
given in the operating instructions.
Attention ! Never operate the micro-
wave oven with the lift door closed.
Such operation would damage your
appliance and invalidate the guarantee.
8
EMS 2487

Electrical connections

Connecting to the mains
• The oven is delivered with the power
cord and a plug for 230-240 V, 50Hz,
earthed socket outlet.
• Earth protection minimizes the risks
should a short-circuit occur. Check to
ensure the voltage of the oven matches
the supply. N.B. If the oven is connected
to the socket via an extension cord,
make sure the cord is earthed.
This appliance must not be used on a non-
earth protected power supply. Contact an
electrician if you are uncertain regarding
electrical connection of the oven or pro-
vision of earth protection of the supply.
• Microwave power output : 900W
• This appliance complies with E.E.C.
directive No. 87/308 of 2.6.87 relative to
radio interference suppression.
Information concerning UK installation
• If this appliance is fitted with a non-rewi-
rable plug for which your socket is un-
suitable, the plug should be cut off and
the appropriate plug fitted. If it is neces-
sary to change the fuse in a nonrewi-
rable plug, the fuse cover must be refit-
ted. If the fuse cover is lost or damaged,
the plug must not be used until a re-
placement is obtained.
• The plug moulded on to the lead incor-
porates a fuse. For replacement, use a
13 Amp BS1362 fuse. Only ASTA or
BSI approved fuses should be used.
• The plug must not be used if the fuse
cover/carrier is lost. The cover/carrier is
indicated by the coloured insert at the
base of the plug. A replacement cover /
carrier is indicated by the coloured
insert at the base of the plug and must
be obtained from your local Electrolux
Service Centre.
IMPORTANT
• The wires in the mains lead are coloured
in accordance with the following code:
GREEN AND YELLOW EARTH
BLUE NEUTRAL
BROWN LIVE
• If you fit your own plug, the colours of
the wires in the mains lead of your
appliance may not correspond with the
markings identifying the terminals in
your plug, proceed as follows:
Connect the green and yellow (earth)
wire to the terminal in the plug which is
marked with the letter 'E' or the earth
symbol ( ) or coloured green and
yellow.
Connect the blue (neutral) wire to the
terminal in the plug which is marked
with the letter 'N' or coloured black.
Connect the brown (live) wire to the ter-
minal in the plug which is marked with
the letter 'L' or coloured red.
GREEN & YELLOW
13 AMP FUSE
BROWN
BLUE
CORD
CLAMP
9