Maintenance - Mr. Heater Portable Buddy MH9B Operating Instructions And Owner's Manual

•
Fully turn Control Knob to "HI" position to light burner
tile. Leave on "HI" position until burner tile turns bright
orange.
•
After burner tile has turned bright orange, adjust heat
output by turning Control Knob to desired position
("LO" or "HI" setting)
•
DO NOT OPERATE HEATER UNLESS CONTROL KNOB IS
SECURED IN A POSITION MARKED "HI", "LO" or
"PILOT".
•
To shut off heater, shut off propane at supply tank,
allow heater to use-up propane in supply line until
heater shuts off, then slightly push down and turn
Control Knob clockwise to "OFF" position.
•
CAUTION: After turning heater off, wire guard will
remain hot. Allow to thoroughly cool before storing.
•
When not in use, the gas must be turned off at the LP-
gas supply cylinder. When the LP-gas supply cylinder is
not disconnected from the heater, the heater and the
cylinder must be stored outdoors, in a well ventilated
space, out of reach of children, and must not be stored
in a building, garage or any other enclosed area.
•
Indoor storage of the heater is permissible only if the
cylinder is disconnected and removed from the heater.
Cylinders must be stored outdoors out of the reach of
children and must not be stored in a building, garage or
any other enclosed area.

MAINTENANCE:

Always keep the heater area clear and free from combustible
materials, gasoline and other flammable vapors and liquids.
Keep the vent areas (slots in the bottom and the top at the front
of heater) clear at all times.
Visually inspect the pilot flame and burner periodically during
use. The pilot flame should be blue in color (not yellow) and will
extend beyond the thermocouple. The flame will surround the
thermocouple just below the tip, see Figure 2, below. A slight
yellow flame may occur where the pilot flame and main burner
flame meet. The burner should be bright orange (with a slight
Figure 2
5
Mr. Heater | Portable Buddy
blue color around the border, a red-orange haze that is visible on
the ceramic tile is acceptable) and without a noticeable flame.
A blue flame that rolls out at the top of the ceramic tile indicates
an accumulation of dust, lint or spider webs inside the casing
assembly and main burner assembly. If the pilot is yellow or the
burner has a noticeable flame, cleaning may be required.
Use the following procedure to inspect the casing assembly and
main burner assembly.
It is necessary to periodically check the burner orifice and burner
venturi tube to make sure they are clear of insects/nests or
spider webs that may accumulate over time. A clogged tube can
lead to a fire.
1 Allow heater to thoroughly cool before performing any
maintenance.
2 Remove disposable 1 lb. cylinder from heater or turn
OFF gas supply at remote cylinder valve, and disconnect
hose from heater.
3 Remove wire guard from front of heater by gently
bending to remove from holes in front cover.
4 Remove (1) burner assembly retaining screw from
bottom of the heater.
5 Pull burner assembly from front of the heater.
6 Inspect interior of casing assembly for accumulation of
dust, lint or spider webs. If necessary, clean interior of
casing assembly with a vacuum cleaner or apply air
pressure. Do not damage any components within casing
assembly when you are cleaning.
7 Inspect and clean main burner orifice (mounted to pilot
bracket with jam nut) by using a vacuum or apply air
pressure at orifice opening.
8 Inspect and clean pilot (mounted to bracket) by using a
vacuum or apply air pressure through the holes in the
pilot indicated by the arrows in Figure 2, at left.
WARNING: Never use needles, wires, or similar cylindri-
cal objects to clean the pilot to avoid damaging the
calibrated ruby that controls the gas flow.
9 Apply air pressure into ceramic tile of burner assembly
and the venturi tube (with cone on end) to remove
dust, lint or spider webs.
10 Make sure the burner tile assembly is completely seated
against the reflector.
1 1 Carefully slide burner assembly back into casing assem-
bly making sure to center reflector flange with the
casing opening and hold in place while installing burner
assembly screw in the bottom of the heater.
12 Install wire guard by gently bending and inserting into
the (4) holes in the front cover.
Operating Instructions and Owner's Manual