Kenwood TK-190 Service Manual page 2

TK-190
You can use these features, using the programming soft-
ware (KPG-59D). Selector function is selectable channel se-
lect or group select.
The functions for Toggle switch are listed page 7 (Fig. 2).
Right position is active for programmed function on toggle
switch except "group select".
The functions for the top key are listed page 7 (Fig.2).
Hold action and shift action are programmable.
The functions for side key are listed page 7 (Fig.2). Hold
action and shift action are programmable.
The functions for microphone key are listed page 7
(Fig.2). Hold action is programmable.
5-1. No Function
Sounds error operation beep, and no action will occur.
Use this function when the transceiver is required to be
more simple operated.
5-2. AUX.
This function can be programmed when the voice scram-
bler board is not installed.
If this key is pressed, "AUX" icon lights on the LCD and
"CLR/C" port which is inside of the transceiver turns to the
high level. If pressed again, the "AUX" icon goes off and the
"CLR/C" ports turns to the lower level.
5-3. Channel Down
If this key is pressed once, the channel number de-
creases by one step. If this key is hold down, the channel
number decreases continuously.
5-4. Channel Up
If this key is pressed once, the channel number increases
by one step. If this key is hold down, channel number in-
creases continuously.
5-5. Channel Name
This key switches the LCD display between the current
channel number and programmed channel name.
5-6. Delete/Add
This key switches the currently displayed channel be-
tween "Delete" and "Add".
The "Add" channel contained in the scan sequence, and
"Delete" channel is not contained. In the scan mode, this
key switches the channel delete or add temporarily.
5-7. Home Channel
Press this key once, the channel switches to the pre-pro-
grammed home channel. Press this key again, the channel
goes back to the previous channel.
5-8. Invert Display
Press this key once, the displayed the channel number or
channel name are inverted. Press this key again, the display
returns to the normal.
For the operator who does not change the display and
needs "Invert" only, refer "Invert Display" setting of optional
feature.
8
fineline6
OPERATING FEATURES
5-9. Key Lock
try of only the [Shift], [KeyLock], [PTT], [Emergency] keys,
[Selector switch], [Volume], [Toggle], [Lamp], [Moni], [Moni
monentary], [SQ off], [SQ momentary] and [SP Attennation]
press which might cause a transceiver malfunction. The dis-
play does not change while the key is being locked.
transceiver can still receive. Pressing this key while scan-
ning, keys are locked but a scanning continues.
5-10. Lamp
back lit approximate 5 seconds. Press this key again, the
transceiver stops the illuminating.
nated restarts the 5 second timer.
5-11. Low Power
changes to Low. Press this key again, the transmission
power returns to programmed value.
5-12. Monitor
speaker if a carrier is present, regardless of the specified
signalling (including option signalling). Press this key again,
"MON" disappears and mutes speaker.
Option Signaling is reset. DBD (Dead Beat Disable) mode is
not reset by this operation.
5-13. Monitor Momentary
is activated. Release this key, the monitor function is de-
activated.
5-14. Operator Selectable Tone
code QT/DQT to OST (Operator Selectable Tone) tone pair.
mode. In this mode, the display shows "OFF" and the opera-
tor can select one of the OST tone pair using the Side 1/Side
2 key. The display shows "TONE
selected or OST name.
select mode, and returns to the channel mode with "OPT"
icon. "OPT" icon means that the OST tone pair is selected.
OST tone pair number or OFF can be memorized for each
channel.
KPG-59D. OST is useful to access the repeater with same
radio frequency and different tone (QT/DQT).
Pressing this key causes the transceiver to accept an en-
"Lock" is used to prevent users from unexceptable key
Pressing Key Lock again cancels the key lock. Key locked
Press this key, the transceiver illuminates the display and
Pressing any key except the LAMP key while the illumi-
Press this key, the transmission power of all channel
Monitor the channel before a transmission.
Press this key once, "MON" appears and unmutes
Press this key after the Option Signalling is matched, the
While pressing this key, the monitor function (refer 5-12)
This key switches the pre-set decode QT/DQT and en-
Press this key, the transceiver enters to OST select
Press OST key again, the transceiver exits from the OST
16 kinds of tone pair for OST can be programmed by
" and tone pair No. is