Maintenance; Solutions To Possible Problems - CALOR 6610 User Instructions

THERMOSTAT THERMOSTAT
3
First turn the control dial to any position other than off First turn the control dial to any position other than off
(except model 6616).
To increase the temperature, turn the thermostat dial to setting 9.
To increase the tempera t u r e, turn the thermostat dial to setting 9.
To reduce the temperature, turn the thermostat dial anti-clockwise (to setting 1)
To reduce the temperature, turn the thermostat dial anti-clock-
The appliance will stop automatically as soon as it reaches the chosen temperature. It will restart, if necessary,
wise (to setting 1)
to maintain this temperature.
The appliance will stop automatically as soon as it reaches the
chosen temperature. It will restart, if necessary,
to maintain this temperature.
FROST-FREE POSITION
This position enables you to keep the temperature automatically above 0°C in a normally insulated room, whose volume corresponds
ENG
OVERHEAT SAFETY CUT-OUT
5
to the power of your appliance.
In some circumstances, the safety cut-out
To do this:
device automatically cuts the electrical power
- set the thermostat dial to frost-free position
supply.
- turn the control dial to
- In the event of overheating, first do the follo-
wing:
Mod. 6616: turn the thermostat dial to frost-
OVERHEAT SAFETY CUT-OUT
free position .
Other models: turn the control dial to
stop: .

5 - MAINTENANCE

After turning the control dial to
to for model 6616, unplug the appliance and let it cool
down completely.
Regularly dust the air inlet and outlet grills with a dry cloth or
vacuum cleaner, without dismantling the appliance.
To remove stains, use a slightly dampened cloth.
Never use alcohol or solvents.
6 - STORAGE
If the appliance is not to be used for some time, unplug it and
protect it from dust and damp.
Wait for the appliance to cool before storing it.

8 - SOLUTIONS TO POSSIBLE PROBLEMS

Problems
The appliance does not heat
The appliance does not bl ow out
hot air: (mod. 6670/6672)
The appliance does not heat enough:
For any other problems, please contact your retailer or your Approved Service Centre.
T H E N F O R A L L M O D E L S P R O C E E D A S F O L L O W S :
.
- unplug the power plug
(mod. 6618 / 6670) or half-power
- remove dust and clean the grills without disassembling the appliance.
- let the appliance cool down for 15 mins.
- plug in the appliance and turn it back on.
an approved service centre.
To restart the appliance, put it back into a stable upright position.
, or the thermostat dial
Possible causes
It is not plugged in correctly.
The control dial is set to "off":
(except 6616).
The thermostat dial setting
is too low compared with
the temperature in the room.
The appliance turned itself
off automatically, as the air
inlet (or air outlet) is clogged.
The appliance has been
tipped over: the anti-tip-over
safety device has cut the power supply.
The "fan" position has not
been selected.
The thermostat setting is too low.
The power choice is too low.
4 FROST-FREE POSITION
(except model 6616). This position enables you to keep the temperature automatical-
ly above 0°C in a normally insulated room, whose volume cor-
responds to the power of your appliance.
To do this:
- set the thermostat dial to frost-free position
- turn the control dial to
(mod. 6610 / 6620 / 6672).
(mod. 6610 / 6620 / 6672).
If the overheat safety device cuts out again, have the appliance checked by
If the appliance tips over.
Important: Never let water enter the appliance.
If the power lead is damaged, or if the appliance becomes
defective, please consult an Approved Service Centre; a special
tool is needed to dismantle the appliance.
7 - GUARANTEE
This appliance is intended for domestic or office use only. It is
not suitable for industrial use or for use in public places.
Failure to comply with the terms of these instructions will ren-
der the guarantee null and void.
(mod. 6618 / 6670) or half-power
Solutions
Check connections.
Turn it to , or or .
Turn it to a higher setting.
See "overheat safety device"
paragraph.
Stand up the appliance
and place it on a fully horizontal floor.
Turn the control dial to the
"fan" setting.
for the 6670, for the 6672
If the appliance still does not blow out hot
air, contact an Approved Service Centre.
Increase the thermostat setting.
Turn the control dial to the next highest
setting. (mod. 6610 / 6620 / 6672).
.