There is an increased risk of electric shock if your body is grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. Page 2 SKU 95105 For technical questions, please call 1-800-444-3353...
Do not use the power tool if the power Switch does not turn it on or off. tool that cannot be controlled with the Power Switch is dangerous and must be re- placed. Page 3 SKU 95105 For technical questions, please call 1-800-444-3353...
Page 4
SpEcIFIc SAFETy RuLES FOR THIS pRODucT Maintain labels and nameplates on the Nitrogen Generator and Inflater. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Always wear ANSI-approved safety impact eye goggles and heavy work gloves when using the Nitrogen Generator and Inflater.
“live” terminal. (See 3-prong plug and Outlet.) The tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like REV 07h Page 5 SKU 95105 For technical questions, please call 1-800-444-3353...
Make sure the extension cord is properly wired and in good electrical condition. Al- ways replace a damaged extension cord or have it repaired by a qualified electrician before using it. Page 6 SKU 95105 For technical questions, please call 1-800-444-3353...
Page 7
Assembly Drawing and Parts List at the end of this manual. Also see Figure C on the next page. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible.
Outlet. The hose for this connection is not supplied. Filter-Regulator (10) Hose Connection from Main Unit (front) Main Unit (rear) Air Compressor Hose Connections Extra N Tank Connection Figure D Page 8 SKU 95105 For technical questions, please call 1-800-444-3353...
This step extracts the air from the tire. Inspect the tire for any leakage. Note: If this “flats” the tire, it should be raised so rim does not damage tire. When air has been extracted, close (90° to air hose) the Air Inlet valve. Page 9 SKU 95105 For technical questions, please call 1-800-444-3353...
4. Reconnect tire valve hose connector. Purity Analysis Display Adjustment of the N 2 Purity Flow Adjust the N 2 Purity Flow Rate reads less than 95% Rate screw is required screw. Page 10 SKU 95105 For technical questions, please call 1-800-444-3353...
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. REV 08h Page 11 SKU 95105 For technical questions, please call 1-800-444-3353...
Screw, M8 x 20 Safety Valve Elbow Connector, ¼” x 8 Note: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. Page 12 SKU 95105 For technical questions, please call 1-800-444-3353...
Page 13
MAIN uNIT MAjOR ASSEMBLy DRAWING Page 13 SKU 95105 For technical questions, please call 1-800-444-3353...
Page 14
MAIN uNIT SuBASSEMBLy DRAWINGS Page 14 SKU 95105 For technical questions, please call 1-800-444-3353...
Page 15
TIRE INFLATER uNIT ASSEMBLy DRAWING Page 15 SKU 95105 For technical questions, please call 1-800-444-3353...
LIMITED 1 yEAR / 90 DAy WARRANTy Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship.