Summary of Contents for Weslo Cadence 815 Treadmill
Page 1
CUSTOMER HOT LINE: 1-888-936-4266 Mon.–Fri., 8 a.m.–6:30 p.m. EST CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. www.weslo.com...
TABLE OF CONTENTS IMPORTANT PRECAUTIONS ..............2 BEFORE YOU BEGIN .
Page 3
9. Use only a CUL-listed surge protector, rated continuously for longer than 1 hour. at 15 amps, with a 14-gauge cord of five feet or less in length. Do not use an extension 18. Never leave the treadmill unattended while it cord.
BEFORE YOU BEGIN Thank you for selecting the WESLO CADENCE ® please call our Customer Service Department toll-free treadmill. The natural motion and versatility of tread- at 1-888-936-4266, Monday through Friday, 8 a.m. mills have made them the most popular way to get an until 6:30 p.m.
ASSEMBLY Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Refer to the drawings below to identify small parts used in assembly. Assembly requires an adjustable wrench (not included).
5. The Console (3) requires two "AA" batteries (not included). Alkaline batteries are recommended. Slide the Battery Cover (15) up as shown. Press two batteries into the battery compartment, with the negative (–) ends of the batteries touching the springs. Close the battery cover. Batteries 6.
OPERATION AND ADJUSTMENT THE PERFORMANT LUBE WALKING BELT risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a Your treadmill features a walking belt coated with grounding plug. Plug the power cord into a surge PERFORMANT LUBE , a high-performance lubricant.
Page 8
DIAGRAM OF THE CONSOLE Speed Control Monitor Display Pulse Display On/Off Scan Button Button Note: If there is a thin sheet of clear Clip Pulse Sensor plastic on the console, remove it. Insert the key fully into the power switch. CAUTION: Before operating the con- sole, read the following important precautions.
Page 9
the walking belt, slide the speed control to the this level. After 5 to 10 seconds, your pulse will be "RESET" position. displayed. Hold your thumb on the sensor for another 15 seconds for the most accurate reading. Press the MODE button to select the desired If the displayed pulse appears to be too high or too monitor mode.
TROUBLE-SHOOTING AND STORAGE Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies to your treadmill and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-free at 1-888-936-4266, Monday through Friday, 8 a.m. until 6:30 p.m. Eastern Standard Time (excluding holidays).
Page 11
5. SYMPTOM: THE WALKING BELT IS OFF-CENTER a. If the walking belt has shifted to the left, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn the rear roller adjustment bolt clockwise 1/4 of a turn. Plug in the power cord, insert the key and run the treadmill for a few min- utes.
CONDITIONING GUIDELINES Training Zone (Beats/Min.) WARNING: Before beginning Unconditioned Conditioned this or any exercise program, consult your physician. This is especially important for 138-167 133-162 individuals over the age of 35 or individuals with pre-existing health problems. 136-166 132-160 135-164 130-158 The pulse sensor is not a medical device.
Page 13
Training Zone Exercise to cool down. This will increase the flexibility of your muscles and will help to prevent post-exercise problems. After warming up, increase the intensity of your exer- cise until your pulse is in your training zone for 20 to Exercise Frequency 60 minutes.
Friday, 8 a.m. until 6:30 p.m. Eastern Standard Time (excluding holidays). When ordering parts, please be pre- pared to give the following information: • The MODEL NUMBER of the product (WCTL81590) • The NAME of the product (WESLO CADENCE ® 815 treadmill) •...
CUSTOMER RECORD Model No.: Serial No.: Retailer Name: Purchase Date: Retailer Address: PLACE STAMP HERE ICON of Canada Inc. 900 de l’Industrie St-Jérôme, Québec Canada, J7Y 4B8...