For paragraphs preceded by the reader should use caution to understand completely the warnings. Ignoring the warnings may result in serious hazards or injuries. - 2 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Network settings................27 Network type ................27 HTTP ..................28 Email settings.................. 29 I/O settings..................30 Video output ................30 Audio output................30 Digital output................30 Keyboard .................. 31 System log..................32 - 3 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 5
Set server parameter values ........... 39 Upgrade firmware ............40 System logs ..............41 Parameter list ................41 Available parameters on the server........42 D. Technical specifications ..............53 - 4 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
“S-video output” Video output for S-video connector “BNC video output” Video output for BNC connector “RCA audio output” Audio output for RCA connector “Microphone audio input” Microphone input is reserved to support two way audio. - 6 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Ground RS485_A D+, non-inverting RS485_B D-, inverting “Ethernet 10/100 RJ45 socket” Connect to an Ethernet network with a UTP category 5 cable of length shorter than 100 meters according to the standard. - 7 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
During the booting process, red and green LEDs will be on. After booted, the Video Receiver will standby for getting IP address. After getting IP Address, the green LED will blink every second. - 8 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
For more detail. please refer to the user’s manual of Installation Wizard 2. Once installation is complete, the Administrator should proceed to the next section "Initial access to the Video Receiver" for necessary checks and configurations. - 9 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Once the password is set, there is no provision to recover the Administrator’s password. The only option is to restore to the original factory default settings. - 10 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
The option box can be checked to save the password for future convenience. But it is not available to the Administrator for obvious reason. *If the administrator (root user) assigns no password, everybody can access the homepage directly. - 11 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
This chapter explains the layout of the main page. It is composed of the following four sections: Logo of VIVOTEK INC., Menu, Host name, and information of Overview. Video Receiver supports maximum twenty video sources. The display mode can be single channel and multiple channels.
The Video Receiver supports keyboard to send PTZ commands to control PTZ camera. The Video Receiver only supports PELCO-D protocol now. The Video Receiver can send CGI command to control the PT functions of PT 7000 series. - 13 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 15
If the IP address is configured but the channel is disconnected, the video output shows the IP address on the top-right corner. In sequential multi-channel mode, if the periodic channel switch is stopped, there should be a channel ID on the top-right corner. - 14 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Overview If the Video sources have been set, the overview page will show the basic information about the servers. In the default situation, it will show the information of “Single channel mode”. - 15 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 17
If the “Multiple channel mode” is selected, it will show the information of four channels. Please refer to “Video source” setting for detailed information. - 16 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
“Update interval” Select hourly, daily, weekly, or monthly update with the time on the NTP server. Remember to click “Save” to immediately validate the changes. Otherwise, the correct time will not be synchronized. - 17 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Video source settings There are three parts of video source settings: “Mode”, “Video source list”, and “Display list”. - 18 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 20
TV or monitor. The multiple channel mode can display four channels simultaneously (Quad display) twenty-channel sequentially (Sequential display). “Video source list” To manage the video source list. “Auto detection” click this button to search for all detected sources in the same LAN. - 19 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 21
RTSP streaming: Multicast, UDP, TCP and HTTP. Video and audio can be chosen independently. If you want to Use HTTP proxy, configure it first in the Network Settings page. Remember to click “Save” to enable the source settings. - 20 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 22
“Create” click this button if you would like to manually set up the source information. Remember to click “Save” to enable the source settings. - 21 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 23
“Delete” Select a video source from the list and then click this button to delete it. “Information” Select a video source from the list and then click this button to open the Video information window. - 22 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 24
"Single channel mode" You can only add one video source to the Display list, and the Video Receiver will show only one channel in video output. The video resolution can be set up to D1. Remember to click “Save” to enable the source settings. For example: - 23 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 25
“Channel switch period” for the sequential display. Click “Up” or “Down” to adjust the display order, or click “Remove” to delete the source from the Display list. Remember to click “Save” to enable the source settings. For example: - 24 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 26
"Quad display" You can add up to 4 video sources to the Display list, and the video receiver will show four channels at the same time. The maximum video resolution will be limited to CIF. - 25 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
The typed entries will be displayed as asterisks for security purposes. <url> http://<Video Receiver>/setup/security.html <Video Receiver> is the domain name or original IP address of the Video Receiver. - 26 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
“PPPoE” If using the PPPoE interface, fill in the following settings from ISP “User name” The login name of PPPoE account “Password” The password of PPPoE account “Confirm password” Input password again for confirmation - 27 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Some invalid settings may cause the system failing to respond. Change the configuration only if necessary and consult with your network supervisor or experienced users for correct settings. Once the system has lost contact, refer to Appendix A for reset and restore procedures. - 28 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Multiple recipients must be separated by semicolon, ‘;’. “Sender email address” The email address of the sender <url> http://<Video Receiver>/setup/mail.html <Video Receiver> is the domain name or original IP address of the Video Receiver. - 29 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
“Quad display mode”. “Sequential display mode” does not support this function. In addition, if the linked video source does not support digital output, the D/O function will be disabled. The digital output will follow D/O #1~#4 (Ex: ) of channel 1~4 (Ex: - 30 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Video Receiver must be set the same with the keyboard. “Baud rate” The transmission speed between Video Receiver and keyboard “Data bits” The length of a data “Stop bits” The length of stop bit “Parity bits” The type of parity check - 31 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Receiver’s buffer area and will be overwritten when reaching a certain amount. The system will send mail with log file when system boot up if the Email settings page has been configured. - 32 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Viewing system parameters The View parameters page lists the entire system’s parameters in alphabetical order. If you need technical assistance, please provide the information listed in this page. - 33 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Note that do not power off the Video receiver during the upgrade. Follow the steps below to upgrade firmware: 1. Download a new firmware file from VIVOTEK website. The file is in pkg file format. 2. Click Browse… and specify the firmware file.
Language Click this button to choose a language for the user interface. Language options are available In the following list: - 35 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Steady Red + Blink Green every UART control message 0.15 sec. Blink Red every 0.15 sec. + Blink Upgrading F/W Green every 1 sec. Blink Red every 0.15 sec. + Blink Restore default Green every 0.15 sec. - 36 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
The CGIs are organized in function related directories under the cgi-bin directory. The file extension of the CGI is required. Syntax: http://<servername>/cgi-bin/<subdir>[/<subdir>...]/<cgi>.<ext> [?<parameter>=<value>[&<parameter>=<value>...]] - 37 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
If you omit this parameter, it will redirect to an empty page. (note: The return page can be a general HTML file(.htm, .html) or a VIVOTEK server script executable (.vspx) file. It can not be a CGI command. have extra parameters.
Post data: fimage=<file name>[&return=<return page>]\r\n \r\n <multipart encoded form data> Server will accept the upload file named <file name> to be upgraded the firmware and return with <return page> if indicated. - 40 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Internal parameters. Unable to be changed by any external interface. Valid values: VALID VALUES DESCRIPTION string[<n>] Text string shorter than ‘n’ characters password[<n>] The same as string but display ‘*’ instead - 41 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Group: sipuac NAME VALUE SECURITY DESCRIPTION (get/set) requesturi_domain <ip address> IP address of server requesturi_sipport 1025 ~ 65535 SIP port of server auth_username string[64] User name used authentication auth_password string[64] Password used authentication - 42 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 44
<positive integer> ptzenabled < boolean > indicate whether to support PTZ control isptz record "camctrl_c0_isptz" value of source. 0 => camera control disable 1 => ptz camera 2 => Transparent HTTP Tunnel - 43 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 45
NTP automatic update interval. restore Restore system parameters <positive integer> default value. Restart the server after <value> seconds if <value> is positive integer. reset 0, -1, Restart server after <value> - 44 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 46
Available language lists ~(count-1)> Group: security NAME VALUE SECURITY DESCRIPTION (get/set) user_i0_name string[64]/18 User’s name, only root’s account user_i0_pass password[64] User’s password, only root’s account user_i0_privile admin Privilege of user i0 usercount User count - 45 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 47
Display mode in multiple channel mode quad switchperiod 5-99 The channel switch period in sequential display mode modulation ntsc, Modulation for video output overscan <boolean> Support OverScan mode - 46 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 48
<ip IP address of server address>[15]/16 subnet <ip address> subnet mask router <ip address> default gateway dns1 <ip address> primary DNS server dns2 <ip address> secondary DNS server - 47 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 49
Group: server NAME VALUE SECURITY DESCRIPTION (get/set) email_ string[128]/ The address of SMTP server i<0~(n-1)>_address email_ string[64]/4 The username to login in the i<0~(n-1)>_username server email_ string[64]/4 The password of the user i<0~(n-1)>_passwd - 48 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 50
2-1.5 , data bit is 5 paritybit none, odd, even Group: syslog NAME VALUE SECURITY DESCRIPTION (get/set) enableremotelog <boolean> enable remote log serverip <IP address> Log server IP address serverport 514, Server port used for log 1025~65535 - 49 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 51
SSL protocol_rtsp < boolean > indicate whether to support rtsp protocol_sip <boolean> indicate whether to support protocol_rtp_multicast_ <boolean> indicate whether to support scalable scalable multicast protocol_rtp_multicast_ <boolean> indicate whether to support - 50 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 52
<boolean> indicate whether to support line output audio_headphoneout <boolean> indicate whether to support headphone output audioin_codec <a list available codec list available codec audio input - 51 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 53
Indicate whether to support the wireless 802.11g wireless_encrypt_wep <boolean> Indicate whether to support the wireless WEP wireless_encrypt_wpa <boolean> Indicate whether to support the wireless WPA wireless_encrypt_wpa2 <boolean> Indicate whether to support the wireless WPA2 - 52 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 55
GB PAT. 819303; IT PAT. 819303; JP PAT. APP. 8-529817; NL PAT. 819303; SE PAT. 819303; US PAT. 5664053. THE LIST MAY BE UPDATED FROM TIME TO TIME BY LICENSORS AND A CURRENT VERSION WHICH AVAILABLE LICENSOR’S WEBSITE HTTP://WWW.VOICEAGE.COM - 54 - www.vivotek.com T: 886-2-82455282 F: 886-2-82455532...
Page 56
VIVOTEK Inc. cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice. VIVOTEK Inc. makes no warranty of any kind with regard to the material contained within this document, including, but...