Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GBC 4064WF-1
Summary of Contents for GBC 4064WF-1
-
Page 1: Cover
GBC 4064WF-1 Operation Manual GBC 4064WF-1 INSTALLATION & OPERATING MANUAL Part Number: TBD, Rev A. Operating Instructions Istruzioni per l'Uso Bedienungsanleitungen Gebruiksaanwijzing Mode d'Emploi Instrucciones de Operación Part Number: TBD © 2009 GBC an ACCO Brands Co. Page 1... -
Page 2: Legal Disclaimer
GBC si riserva il diritto di effettuare cambi a questo documento e ai prodotti in esso descritti senza preavviso. Tutte le specifiche e le informazioni sui prodotti sono soggette a cambio senza preavviso. -
Page 3: Table Of Contents
Slitter Blade Slitter Bar Mounting Pull Roller Clutch Main Circuit Breaker Fuses Foot Switch Power Cord © 2009 GBC an ACCO Brands Co. Page Description Sequence of Operations Operating Instructions Film Loading and Threading Load a Roll of Film Webbing Thermal Film using... -
Page 4: Important Safety Instructions
EACH SAFETY OR REPAIR THE LAMINATOR INSTRUCTION Disconnect the plug from the receptacle and contact GBC’s Technical Department or your dealer/distributor when one or more of the following has occurred. ATTEMPT • The power supply cord or attachment plug is damaged. -
Page 5: Warranty
GBC 4064WF-1 WARRANTY Limited 90- Day Warranty GBC warrants to the original purchaser for a period of ninety days on labor and one year on parts after installation that this laminator is free from defects in workmanship and material under normal use and service. GBC’s obligation under this limited warranty is limited to replacement or repair, at GBC’s... -
Page 6: Pre-Installation
Finally, check by placing the level diagonally across lower main to lower pull rolls. © 2009 GBC an ACCO Brands Co. Operation Manual Before a 4064WF-1 Laminator can be installed, ensure the following requirements are met: Are doorways and hallways wide enough for the... -
Page 7: Front Control Guide
• Increases (+) or decreases (-) the numeric value for the selected setting when turned. Navigates through the Job Selections. © 2009 GBC an ACCO Brands Co. Operation Manual 7. Front Roller Press: • When pressed, the Main Rollers will move to the Press or Down position. -
Page 8: Lamination Processes
GBC 4064WF-1 Operation Manual There are 2 Lamination Processes on 4064WF-1, LAM and ACCUSHIELD. LAM: This setting is intended to be used when an operator wants to use both the top and bottom heater, and wants full downward pressure on the Main Rolls. -
Page 9: Accushield Mode
The distance this machine ran since being reset is 96ft. READY Indicates that the temperature has reach the desired set-temp. Speed is set for 3ft/mn The direction of the laminator is set to go forward. © 2009 GBC an ACCO Brands Co. Page 9... -
Page 10: Saving Temps And Speeds
Operation Manual Saving Temps and Speeds The operator is able to save Temps and Speeds for certain processes on the 4064WF-1. When operating the laminator in the lamination mode, the operator can save the Speed, Top Heat, & Bottom Heat. -
Page 11: Lcd Quick Reference
BOT: 032*F SPD: 03ft POS: LAM FRONT FR ACTIVATE SAFETY!!! © 2009 GBC an ACCO Brands Co. Operation Manual FIGURE 1: When jobs are changed, the shim dials will automatically rotate to the desired setting. Front Tension Error indicates that the Front Shim Dial has not located the desired setting. -
Page 12: Lcd Detailed Reference Sheet
(To see the current actual temp, press and hold the Master Dial.) • REAR indicates that the unit is set to run in reverse mode. © 2009 GBC an ACCO Brands Co. WAIT TOP: 230*F SPEED: 05ft BOT: 230*F REAR POS: ½”... -
Page 13: Features Guide
FIGURE D 1. Safety Light Beam System: (FIGURE D, Item 1) The 4064WF-1 uses a Safety Light Beam to protect the end-user from harm. When this Beam is blocked, the Rollers will stop rotating. Once the Beam is interrupted, the operator must re-start the machine by pressing Run. -
Page 14: Main Air Supply
PSI, turn the knob counter clock-wise. FIGURE G 1. Main Air Supply: (FIGURE G, Item 1) The 4064WF-1 requires Compressed Air. Connect to the Main Air Supply at #1. FIGURE H 1 & 3. Swing -Out Film Unwind Shaft Brake Tension Knob: (FIGURE H, Item 1 &... -
Page 15: Pull Roller Clutch
4. Main Power Cord: (FIGURE M Item 4) The main Power Cord is used to supply Main voltage to the Laminator. © 2009 GBC an ACCO Brands Co. Operation Manual FIGURE N 1. Main Power Cord. (FIGURE N Item A) The Main Power Cord Plugs into the Main Power Supply. -
Page 16: Sequence Of Operations
Reverse Mode to change mode and Press Reverse take over from control Push button switch. panel. © 2009 GBC an ACCO Brands Co. Situation 2 Interrupted fiber optic beam or opened any safety circuitry. Machine stops Instantly. Use foot pedal to override @ 3f/m. -
Page 17: Operating Instructions
Always change the top and bottom supply rolls at the same time. Near the end of each roll of GBC laminating film is a label stating “Warning-End of Roll”. The appearance of this label on either the top... -
Page 18: Webbing Thermal Film Using Threading Card
12. Once the threading card has completely exited the pull rollers, press the stop ( 13. Now refer section LAMINATING. © 2009 GBC an ACCO Brands Co. to On. ) button. entitled START Operation Manual THERMAL... -
Page 19: Webbing Psa Film/Mount Adhesive Using Threading Card
Film CHILLED ROLLER HEAT ROLLER Mount Adhesive FIGURE 24 © 2009 GBC an ACCO Brands Co. Operation Manual Webbing PSA Film/Mount Adhesive Using Threading Card The laminator should be cool to the touch before Proceeding. 1. Turn the Power ON... -
Page 20: Start Laminating
CAUTION: Avoid forcing the image into the main roller nip as this action will cause the corners of the leading edge to buckle and create a wave. © 2009 GBC an ACCO Brands Co. Operation Manual FIGURE 25 FIGURE 26... -
Page 21: Method For Tacking New Film To Existing Film
FIGURE 27 ...a PSA film or mount adhesive FIGURE 28 © 2009 GBC an ACCO Brands Co. Method for Tacking New Film to Existing Film The following describes a method for loading film whereby the existing film present on the heat rollers may be used in place of the threading card to draw the new film through the laminator. -
Page 22: To Unweb The Laminator
6. Once the film jam has been cleared, lower the main roller and pull rollers. 7. Refer section titled LAMINATING. © 2009 GBC an ACCO Brands Co..a PSA film or mount adhesive START Operation Manual FIGURE 29 PULL WEB... -
Page 23: Applications
RELEASE LINER FROM PSA FILM IMAGE KRAFT PAPER OPTION FIGURE 33 © 2009 GBC an ACCO Brands Co. Tips for Pre Coating Boards MOUNT ADHESIVE 1. Load the laminator as illustrated in (Fig. 31). LEADER BOARD 2. The width of the roll should not exceed the 3. -
Page 24: Creating A Decal
6. Length and width of image, ink coverage and paper type may affect the temperature and speed recommended in the SPEED/ TEMPERATURE GUIDE. © 2009 GBC an ACCO Brands Co. THERMAL OR PSA FILM RELEASE LINER FROM PSA FILM... -
Page 25: Accushield
PAPER OPTION FIGURE 37 FIGURE 38 FIGURE 39 © 2009 GBC an ACCO Brands Co. Tips for AccuShield 1. Load the laminator as illustrated in Fig. 37. 2. You must have the Separator bar option to OPTIONAL accurately run this material. See your Sales Rep SEPERATOR BAR for ordering the Separator Bar. -
Page 26: 2-Sided Psa
GBC 4064WF-1 Operation Manual © 2009 GBC an ACCO Brands Co. Page 26... -
Page 27: 1-Sided Psa
GBC 4064WF-1 Operation Manual © 2009 GBC an ACCO Brands Co. Page 27... -
Page 28: 2-Side Thermal
GBC 4064WF-1 Operation Manual © 2009 GBC an ACCO Brands Co. Page 28... -
Page 29: Psa Decal
GBC 4064WF-1 Operation Manual © 2009 GBC an ACCO Brands Co. Page 29... -
Page 30: Psa Mounting
GBC 4064WF-1 Operation Manual © 2009 GBC an ACCO Brands Co. Page 30... -
Page 31: Speed/Temperature Control
Setting the speed control at slower settings gives the laminator longer dwell time thus allowing proper lamination of thick items. Thinner items, such as standard copier paper (20 lb. bond) and tissue paper, extract less heat from the rollers and can be run at faster speeds. © 2009 GBC an ACCO Brands Co. Page 31... -
Page 32: Film Tension
- A - FIGURE 40 - A - FIGURE 41 © 2009 GBC an ACCO Brands Co. Heat The “READY” indicator may extinguish if the speed is set too fast for the material being laminated. Either lower the speed setting or press STOP ( ) and wait until the “READY”... -
Page 33: Maintenance
GBC offers Cleaning kits as well as Extended Maintenance Agreements. Contact your local GBC Service Representative or your dealer/distributor for additional information. The only maintenance required by the operator is to periodically clean the heat rollers and schedule semi annual maintenance checks. The following procedure will help keep the heat rollers free of adhesive that has been deposited along the edge of the laminating film. -
Page 34: Trouble Shooting Guide
SERVICE AGREEMENT GBC’s Equipment Maintenance Agreement will insure the quality performance and long life built into your laminator. A service charge for travel time, labor and parts may be incurred for each out of warranty service call. GBC’s Equipment Maintenance Agreement Decreases these expenses and protects your valuable investment.