Page 2
Č ý Českého průvodce rychlou instalací naleznete na Č ý přiloženém CD s ovladači. Auf der beiliegend Treiber CD finden Sie deutsche Anleitung zur Schnellinstallation. ñ Incluido en el CD el G.R.I. en Español. ñ ç Veuillez trouver l’français G.I.R ci-joint dans le CD. ç...
1 Product Introduction ................4 1-1 Package Contents ................ 5 1-2 Front Panel .................. 5 1-3 Back Panel ................... 6 p ..................7 : ..............7 n ............. 9 n ..............12 p ............12 ( A ) Plug and play, no setup procedure required...... 12 ( B ) PIN code or user name / password required: ....
1 Product Introduction Thank you for purchasing Edimax 3G-6200n / 3G-6400n wireless 3G broadband router! This high cost-efficiency router is the best choice for Mobile / Small office / Home office users, all computers and network devices can share a single wireless 3G modem or xDSL / cable** modem internet connection at high speed.
Guide and User Manual) □ 12V power adapter (1 pcs) □ Ethernet Cable (1 pcs) □ Holding Base (1 pcs) □ Accessories 1-2 Front Panel 3G-6200n / 3G-6400n Light Description Status Router is ready WAN is connected WAN is unconnected...
1-3 Back Panel 3G-6400n 3G-6200n Item Name Description Power Power connector, connects to power adapter Reset / WPS Reset the router to factory default settings (clear all settings) or start WPS function. (a) Press this button and hold for 20 seconds to clear all settings.
2. Connect another Ethernet cable from the any LAN ports (1~4) on router to the Ethernet socket on the PC 3. Insert SIM card into 3G/3.5G modem card, and connect the modem card with one of USB port of 3G-6200n / 3G-6400n. The corresponding USB LED indicator on 3G-6200n / 3G-6400n will light.
Page 9
If you do not have 3G USB modem. You can also access Internet by xDSL/Cable modem, please follow the following instructions: 1. Connect the Ethernet cable from the router’s WAN port to the LAN port of the modem. 2. Connect another Ethernet cable from the any LAN ports (1~4) on router to the Ethernet socket on the PC.
Configure the PC LAN setting to automatically obtain an IP address from the router by following the below steps. Click “Start” in the task bar then select the “Control Panel” . Click “Switch to Classic View” on the left top to see more setting icons.
Page 11
Find an icon “Network Connection” then Double-Click to open the network connection setting. You will see an icon “Local Area Connection”, select the icon then Right-Click the mouse to open the sub-menu and select the “Properties” . Select the “Internet Protocol (TCP/IP)” then click the “Properties”...
Page 12
Ensure the parameter marked in blue are checked in “Obtain an IP address automatically” and “Obtain DNS server address automatically” then press “OK” to close.
Related instructions will be given as follow. 3G-6200n / 3G-6400n supports most of 3G/3.5G modem cards, just connect the modem card to the USB port of 3G-6200n / 3G-6400n and 3G-6200n / 3G-6400n will recognize it automatically, no additional setup procedure required. However, some of modem cards require PIN code or account / password (you have to use 3G-6200n / 3G-6400n’s web interface to input these information), and some modem cards...
Page 14
can use the web browser to access Internet. ( B ) PIN code or user name / password required: If you still can’t access Internet, please enter the router’s default IP address: “192.168.2.1” into your PC’s web browser and press “enter” The login screen below will appear.
Page 15
If telecomm provider provides you with username / password, please check /User Name / Password box and input the user name / password provided by telecomm service provider, then click ‘ OK ’ button. Wait for 1 minute (for 3G-6200n / 3G-6400n to reboot), then you can access Internet.
Please input User name & Password in “PPP Settings” and do not input them in “Network Settings” unless your ISP ask you input them in both. Note: Please choose “CDMA”, if your ISP use 3G CDMA system. ( C ) Driver / Utility required on PC side Some 3G/3.5G modem card does not work with instructions (A) or (B) listed above (ex.
Page 17
every PC which needs to access Internet first. After driver / utility installation is complete, every PC will be able to access Internet via 3G/6200n / 3G-6400n. 1. Plug in the BandLuxe C100S modem card to the USB port of your computer. 2.
Page 18
4. Please go to “My computer”, you will see the BandLuxe C100S. Double click the device. 5. The program inside the adapter will prepare to install the driver and utility of the adapter.
Page 19
6. Click “Next”. 7. Select “I accept the terms in the license agreement” and click “Next”.
Page 20
8. If you want to change the destination folder, please click “Change”. Click “Next” to continue. 9. Click “install”.
Page 21
10. The system is installing the driver and utility of the adapter. 11. Install successfully, click “Finish” to close the install wizard.
Page 22
12. The utility of C100S will start up automaticity. Please select the “MENU” 13. Click “Setting”. 14. Select the “Auto connect on startup”.
Page 23
15. Plug in the C100S into the USB port of the 3G router. 16. The USB adapter will get the IP address from ISP automatically. You can check the Status of the 3G-6200n / 3G-6400n on the Web site (ex: 192.168.2.1).
Page 24
Note : If your SIM card requires entering the PIN code, please enter into the web management of the 3G router. In WAN setting web page, select 3G/3.5G. Enter the PIN code of the adapter. ...
2-3-2 – – The following instruction will help you to get connected if you have xDSL / cable Internet connection Please enter the router’s default IP address: “192.168.2.1” into your PC’s web browser and press “enter” The login screen below will appear. Enter the “User Name” and “Password” and click “OK”...
Page 26
1. Select “PPPoE xDSL”, the system will move into next step 2. Enter the “User Name” and “Password” that ISP provided and leave the others. (The “Service Name” can be blank) and click “OK” to save the setting then reboot the router 3.
2-3-3 – – Please enter the router’s default IP address: “192.168.2.1” into your PC’s web browser and press “enter” The login screen below will appear. Enter the “User Name” and “Password” and click “OK” to login. The default User name is “admin” and Password is “1234”,...
Page 28
1. Select “Cable Modem”, the system will move into next step 2. Enter ”Host Name” and “MAC Address”. (The “Host Name” can be blank) The MAC Address is provided by ISP (e.g. NTL) or click “Clone Mac Address” button if you’re using the computer’s MAC Address. Confirm with your ISP about MAC Address used, Click “OK”...
3 Advanced Setup 3-1 Change management password Default password of this router is 1234, and it’s displayed on the login prompt when accessed from web browser. There’s a security risk if you don’t change the default password, since everyone can see it. To change password, please follow the following instructions: Please click ‘System’...
3-2 Firmware Upgrade The system software used by this router is called as ‘firmware’, just like any applications on your computer, when you replace the old application with a new one, your computer will be equipped with new function. You can also use this firmware upgrade function to add new functions to your router, even fix the bugs of this router.
firmware upgrade procedure automatically. The procedure may take several minutes, please be patient. NOTE: Never interrupt the upgrade procedure by closing the web browser or physically disconnect your computer from router. If the firmware you uploaded is corrupt, the firmware upgrade will fail, and you may have to return this router to the dealer of purchase to ask for help.
3-4 Wireless Setup SSID is the name of the wireless router. You may change your SSID to a meaningful name so that you can identify your wireless router from others. You can use any alphanumeric characters, up to 32 characters. By default the ESSID is ‘default’. It’s very important to set wireless security settings properly! If you don’t, hackers and malicious users can reach your network and valuable data without your consent and this will cause serious security problem.
Page 33
Lithuania, Malta, Poland, Romania, Slovakia, Slovenia, the Netherlands, Portugal, Spain, Sweden, and the United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland. EU Countries not intended for use None A declaration of conformity is available on www.edimax.com N2037...