Channel Fader; Effect Section - Pioneer Serato DDJ-S1 Operating Instructions Manual

m HOT CUE/SAMPLER buttons 1 – 5
Hot cue mode
Press:
Use this to set, play and call out hot cues.
[SHIFT] + press:
Delete the hot cue set for that button.
= Using hot cues (p.19)
Sampler mode
Press:
When one of [HOT CUE/SAMPLER] buttons 1 to 3 is pressed, play-
back of the sample starts.
The bank switches each time [HOT CUE/SAMPLER] button 4 or 5 is
pressed.
[SHIFT] + press:
When one of [HOT CUE/SAMPLER] buttons 1 to 3 is pressed, play-
back of the sample stops.
= Using the sampler function (p.19)
Mixer section
1
MIN
MIN
2
EQ
MIN
MIN
3
6
10
9
8
7
6
5
4
3
2
7
1
0
9
FADER START
a
OFF
b
1 TRIM control
Adjusts the individual channel output gain.
2 EQ (HI, MID, LOW) controls
Boosts or cuts frequencies for the different channels.
3 Headphones CUE button
Press:
The sound of channels for which the headphones [CUE] button is
pressed is output to the headphones.
! When the headphones [CUE] button is pressed again, monitoring
is canceled.
4 MASTER LEVEL control
Adjusts the master sound level output.
5 HEADPHONES MIXING control
Adjusts the balance of the monitor volume between the sound of the
channels for which the headphones [CUE] button is pressed and the
sound of the master channel.
12
En
BACK
LOAD PREPARE
ZOOM SAVE
BROWSE
TRIM AREA TRIM
PANEL REC
4
MAX MIN MAX
HI MASTER HI
LEVEL
MAX MIN MAX
MIN MAX
MID MID
HEADPHONES
EQ
MIXING
5
MAX MIN MAX
LOW LOW
CUE MASTER
LEVEL
MAX MIN MAX
8
MIN MAX
CUE CUE
1 2
LEVEL
1 MASTER 2
10
9
8
7
6
5
4
3
2
1
0
C.F.REV
FADER START
ON OFF ON OFF ON
C.F.REV THRU
d c
6 HEADPHONES LEVEL control
Adjusts the audio level output from the [PHONES] terminal.

7 Channel fader

Adjusts the level of audio signals output in each channel.
8 Channel Level Indicator
Displays the sound level of the respective channels before passing
through the channel faders.
9 Master level indicator
Displays the master output's audio level.
a FADER START switch
These turn the fader start function on/off.
= Starting playback using the fader (Fader Start) (p.20)
b C.F. REV switch
This reverses the channels assigned to the left and right sides of the
crossfader.
[ON]: The left side of the crossfader is set to deck (2), the right side
to deck (1).
[OFF]: The left side of the crossfader is set to deck (1), the right side
to deck (2).
c Crossfader curve selector switch
This switches the crossfader curve characteristics.
[ ]: Set here for a curve that rises steeply. (When the crossfader
moves away from either the left or right edge, the sound is immedi-
ately output from the opposite side.)
[ ]: Set here for a curve that rises gradually.
[THRU]: Choose this when you do not want to use the crossfader.
d Crossfader
Switches between the audio output of the left and right decks.

Effect section

The effect section is used to control two effect units (FX1 and FX2).
There are controls and buttons for operating FX1 on the left side of the
controller, controls and buttons for operating FX2 on the right side of the
controller. Also, the [FX CH SELECT] control is used to set the channel to
which the effect is applied.
BROWSE
FX CH SELECT
EFFECT SELECT
/
LEVEL / DEPTH
MULTIMODE
EFFECT SELECT
PARAMETER 1 PARAMETER 3
FX ON/OFF
PREPARE
2 MASTER
1 MIC
/AUX 1
2
BEATS
PARAMETER
3
4
ON / OFF
5
6
TAP
AUTO
FX MODE
FX2
TAP
BEATS