Download Print this page

Important Setup & Operation Notes; Maintenance And Care; Specifications; Placement Of The H2O Sensor - La Crosse Technology D000.104 Instruction Manual

Replacement h2o sensor on 6 ft. cable for la crosse alerts tx70u-it remote water detector

Advertisement

PLACEMENT OF THE H2O SENSOR

The H2O sensor should be placed on the dry floor or against
the wall near your foundation, water heater, sump, plumbing,
washer aquarium, or dish washer etc. to monitor for leaks.
FLOOR:
Place the H2O sensor (circuit board down) on
the dry floor within range of the water detector
with temperature / humidity that is mounted on
the wall or standing on a table. Note: The water
detector will sit 1/8 inch from the floor in this position.
WALL:
Place the H2O sensor against the wall with the
edge touching the floor within range of the water
detector with temperature/humidity that is
mounted on the wall or standing on a table.
• The H2O sensor can be secured to the floor or wall with the
included screws & anchors or with two-sided tape (not
included).
• Secure the 6 ft. H2O sensor cable to avoid tripping hazards:
Loosely coil and secure the extra cable with a twist tie.
CLEANING THE H2O SENSOR
Routine cleaning of the H2O sensor
is recommended to ensure proper
operation.
Use clean water and a soft cloth to clean dirt and debris from
the circuit board of the H2O sensor.
Note: When using two-sided tape, replace the tape after
cleaning the H2O sensor to maintain adhesiveness.
IMPORTANT SETUP & OPERATION NOTES
• The H2O sensor is not for use in a pool or hot tub
where chemicals may cause malfunction.

MAINTENANCE AND CARE

• Avoid extreme temperatures, vibration, and shock to prevent
damage.
• Clean water detector and H2O sensor with a soft, damp
cloth. Do not use solvents or scouring agents.
• Do not submerge the water detector case in water.
• Avoid kinking the H2O sensor cable.
• Secure the six foot cord to avoid tripping hazards.

SPECIFICATIONS

H20 Sensor on 6 Ft. Cable:
D000.104 H20 Sensor size
6 ft. detachable water sensor cable that
detects wet (H20) and dry (DRY)
conditions. Displays last reading if
probe is not connected.
.26" H x 1.77" W x 1.17" D
DISCLAIMERS
* Disclaimers: La Crosse Technology, LTD. ("La Crosse")
provides various alert and monitoring services to aid users. (1)
Service providers may charge users for alert services.
Standard messaging and data rates apply and will be billed to
the customer's wireless account. Customers may be unable to
receive text messaging or data service in some areas due to
unavailability of service. (2) La Crosse shall not be liable for
accuracy, usefulness or availability of data transmitted via the
service. Users are solely responsible for damages to persons
or property by service use.
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty
on this product against manufacturing defects in materials and
workmanship.
This limited warranty begins on the original date of purchase, is
valid only on products purchased and used in North America
and only to the original purchaser of this product. To receive
warranty service, the purchaser must contact La Crosse
Technology, Ltd for problem determination and service
procedures. Warranty service can only be performed by a La
Crosse Technology, Ltd authorized service center. The
original dated bill of sale must be presented upon request as
proof of purchase to La Crosse Technology, Ltd or La Crosse
Technology, Ltd's authorized service center.
La Crosse Technology, Ltd will repair or replace this product,
at our option and at no charge as stipulated herein, with new or
reconditioned parts or products if found to be defective during
the limited warranty period specified above. All replaced parts
and products become the property of La Crosse Technology,
Ltd and must be returned to La Crosse Technology, Ltd.
Replacement parts and products assume the remaining
original warranty, or ninety (90) days, whichever is longer. La
Crosse Technology, Ltd will pay all expenses for labor and
materials for all repairs covered by this warranty. If necessary
repairs are not covered by this warranty, or if a product is
examined which is not in need or repair, you will be charged for
the repairs or examination. The owner must pay any shipping
charges incurred in getting your La Crosse Technology, Ltd
product to a La Crosse Technology, Ltd authorized service
center. La Crosse Technology, Ltd will pay ground return
shipping charges to the owner of the product to a USA address
only.
Your La Crosse Technology, Ltd warranty covers all defects in
material and workmanship with the following specified
exceptions: (1) damage caused by accident, unreasonable use
or neglect (including the lack of reasonable and necessary
maintenance); (2) damage occurring during shipment (claims
must be presented to the carrier); (3) damage to, or
deterioration of, any accessory or decorative surface; (4)
damage resulting from failure to follow instructions contained in
your owner's manual; (5) damage resulting from the
performance of repairs or alterations by someone other than
an authorized La Crosse Technology, Ltd authorized service
center; (6) units used for other than home use (7) applications
and uses that this product was not intended or (8) the products
inability to receive a signal due to any source of interference..
This warranty covers only actual defects within the product
2

Advertisement

loading