GE PT925 Installation Instructions Manual

Single double wall oven
Hide thumbs Also See for PT925:
Table of Contents

Advertisement

Available languages

Available languages

I
I
tall rio
tr ctio
Single Double Wall Oven
PT925
If gou
have questions,
call 1.800.GE.CARES or visit our website
at: ge.com
i
Before You Begin
Read these instructions corefullg and completelg.
• IMPORTANT-savethese
instructions
for local inspector's
use.
• IMPORTANT-observe a,
governing
codes and ordinances.
• Note to Installer--Be
sure to leave these
instructions
with the consumer.
• Note to Consumer--Keep
these
instructions
for future
reference.
• Proper installation
is the responsibilitg
of the
installer
and product
failure due to improper
installation
is NOT covered under warrantg.
• NOTE--This appliance
must be properlg
grounded.
ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired)into
an approved junction
box.
A plug and receptacle
is NOT permitted
on
these products.
Ports Inclu
ed
{Appearance will varg}
Screws For Installation
(8-18 x .625 Black Dome
Phillips Head)
Hex Nuts
Lower Oven
Rack Supports
with Hex Nuts
30" (76.2 cm)
Metal Bottom Trim Assemblg
31-10696
o7-o8 JR
Materials
Strain Relief Clamp for
1/2" conduit
Needed
Junction Box
Wire Nuts
String 72"
(183 cm)
Tools Needed
Nut Driver 7/16"
(11 mm)
1/8" (3 mm) Drill Bit and
Electric or Hand Drill
Phillips #2
Screwdriver
Wire Strippers

Advertisement

Table of Contents
loading

Summary of Contents for GE PT925

  • Page 1 Single Double Wall Oven tr ctio PT925 If gou have questions, call 1.800.GE.CARES or visit our website at: ge.com Before You Begin • Proper installation is the responsibilitg of the Read these instructions corefullg and completelg. installer and product failure due to improper •...
  • Page 2: Installation

    Installation Instructions I PORTANT SAFETY INSTRUCTIO S For Your Safety ectrical Requirements . Be sure your oven is installed properly by Rating plate is located on oven side trim, side front frame or lower front frame. a qualified installer or service technician. .
  • Page 3 Installation Instructions Pre-lnstallation Checklist ALL INSTALLATION INFORMATION ON THE FOLLOWING PAGES ISTO BE USED FOR SINGLE DOUBLE WALL OVEN INSTALLATION! III Upper Door DO not remove IDDDD Drrrl _D_DD_ Remove packaging materials. during installation Check behind hinges and under elements. Remove labels on the Lower Door outside of the door, plastic on trims...
  • Page 4 Installation instructions Cutout for 3 ouble Single {76.2 cm) Wall Oven g1/2- Cabinet Width 30" (76.2 cm) Cutout 112.7 cm) Width Max. Junction 28 112" Location Recommended (72.4 cm) (junction Cutout Location Min. 28 5/8" located in adja- 26 1/2" (67.3 cm Max.
  • Page 5 Cutoutfor 30" (76.2 Double Oven ingle Under Counter Electric cooktops mag be installedover this oven. See cooktop installation instructionsfor cutout size.See labelon top of oven for approved cooktop models. 240V / 208V Junction Box Location (junction box mag be in adjacent cabinet) 25"...
  • Page 6 Cabinetr Wall Cutoutfor 30"€76.2 cm) S ingle Double Oven- Over a Warming Drawer Single Double 30" 176.2cm) Oven Over a Warming Drawer Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement 2" (5.1 cm) Min. Note: Instoll Per Warming oven onJg with spe- Drawer cific models listed...
  • Page 7: Warming Drawer

    Cabinetr Cutout for 30" (76.2 cm) S ingle Double Wall Oven Below an Advantium or Microwave Oven or Between an Advantium or Microwave Oven and a Warming Drawer Single Double 30" (76.2 cm) Single Double 30" 176.2cm) Oven Below an Advantium Oven Between an Advantium or Microwave Oven or Microwave Oven and a...
  • Page 8: Electrical Connections

    Electrical Connections Turn off the circuit breoker or remove ATTENTION INSTALLER fuses to the oven branch circuit. All electric wall ovens must be hard wired With the oven supported on o toble or (direct wired} into an approved junction box. A platform in front of the cabinet opening,...
  • Page 9 New Construction Three-Conductor Branch Four-Conductor Branch Circuit Connection Circuit Connection When connecting to a three-conductor branch circuit, if local codes permit: installing • When in new construction, a. Connect the bare oven ground conductor • When installing in a mobile home, or with the crimped neutral (white)lead •...
  • Page 10: Securing The Oven In The Opening

    Securing the Oven in the Opening Sliding the Oven Into the Installing the Metal Bottom Trim Opening a. Place the bottom metal trim under air o. Loopldo nettle} a 72" (183 cm) string around the conduit before the oven is slid into place. divider, with side flush against side trim.
  • Page 11: Mounting The Oven

    r&] Installing the Lower Oven Drilling the Pilot Holes and Rack Supports and Oven Mounting the Oven Racks Oven Rack Supports sure the oven is pushed as far back into the opening as it will go and centered. Place the rack support with slotted holes over the rear bolts and round holes over the front bolts.
  • Page 12: Pre-Test Checklist

    Pre-Test Checklist Check that the bottom trim is installed Remove all protective film, if present, and any stickers. properly (see page 11). Check to be sure the mounting screws Check to be sure that all wiring is secure are installed and flush with the side trim and not pinched or in contact with...
  • Page 13 Appendix oor emoval and Lower Oven Instructions Installation DOOR REPLACMENT DOOR REMOVAL Bottom door removal is not recommended for installation of the product. Open the oven door as far as it will go. ull both hinge locks down toward the door Hinge ift oven door bg placing Unlocked...
  • Page 14 otes...
  • Page 15: Partes Incluidas

    Horno de pared simple doble CCIO tal ci6 PT925 ® #.Preguntas? Visite nuestro sitio en la Web: ge.com Antes de empezar Lea estas instrucdones cuidadoso g completamente. • La instalaci6n apropiada es responsabilidad del instalador g la falla del producto par una •...
  • Page 16 Instrucciones de instalaci6n INSTRUCCIO ESEGU IDAD IMPORTANT Para su seguri a Requisitos el ctricos • Cerci6rese de que su horno sea instalado La placa de potencia se encuentra en la moldura lateral del homo, el marco lateral frontal del homo o el marco adecuadamente por un instalador calificado...
  • Page 17 Instrucciones de instalaci6n Lista de control antesde lainstalaci6n Puerta superior_ No quitar durante IDDDD Drrrl Retire los materiales de embalaje. Revise detr6s _D_DD_ la instalaci6n de las bisagras g debajo del fondo falso. Retire las etiquetas de la puerta, el pl6stico de las reborde g panel, todas las cintas alrededor del Puerta inferior homo.
  • Page 18 Carte para los hornos simple/dobles de 30" (7o,z solamente Ancho del 9 112" (12,7 cm) UbicacJ6n gabinete 30" (76,2 cm) de la caja Ancho Ubicaci6n de conexi6n deI corte --). (la caja 28 1/2" recomendada de conexi6n _(72,4 cm) Min. puede estar para el corte 28 5/8"...
  • Page 19 Carte para los hornos simple/dobles de 30" (70.2 c_l- debajo de la superficle del gabinete Topes electricos de cocino se pueden instolor sabre este horno. Consulte instrucciones de la estufo paro el tomato del carte. Consulte la etiqueta encima del homo pora los modelos de estufas aprobados.
  • Page 20 Gabinetes Abertura para hornos simple/do es e 30"€76,2 cmlempotrados Sobre una gaveta de calentamiento Horno individual de 30" (76,2 cm} sobre una gaveta de calentamiento Bloque estable contra la pared trasera para la gaveta de calentamiento requisitos NOTA: Instale el Basado en horno s61o con los requerimientos...
  • Page 21 Gabinetes I_IAbertura p arahornos s impleldobles de30"€76,2 deunAdvantium odeunhorno Debajo demicroondas o EntreunhornoAdvantium o unhornodemicroondas y Gaveta decalentmiento Horno individual de 30" (76,2 cm) Horno individual de 30" (76,2 cm) Entre un horno Advantium debajo de un horno Advantium o un horno de microondas o un horno de microondas g una gaveta de calentamiento Basado en requerimientos...
  • Page 22: Conexiones El Ctricas

    Conexiones el ctricas Desconecte el interruptor del circuito ATENCION AL INSTALADOR: o retire los fusibles que alimentan circuito ramal del horno. Todos los hornos el@ctricos de pared deben ser cableados directamente en una caja de Con el horno enfrente de la abertura del conexi6n.
  • Page 23 Cone×i6n de circuito ramal Conexi6n para nueva de tres conductores construcci6n g de circuito ramal de cuatro conductores Cuando conecte un circuito ramal de :3 conductores, si los c6digos locales Io permiten: • Cuando se instale en una construcci6n nueva, o a.
  • Page 24 © Posici6n firme dei horno en ia abertura © C6mo deslizar el horno en el C6mo taladrar los orificios interior de la abertura piloto y montar el horno a. Coloque (sin atar) una cuerda de 72" o. Coloque el reborde de metal inferior debajo (183 cm) alrededor del conductor antes de del separador de aire, con el costado deslizar el horno en su lugar.
  • Page 25: Bandejas Del Horno

    C6mo instalar los soportes de C6mo taladrar los orificios la bandeja y las bandejas del piloto y montar el horno homo del homo inferior NOTA: Antes de perforar los orificios Soportes de las bandejas del piloto, cerci6rese de que el homo se empuj6 hasta el fondo y de que est_ horno centrado.
  • Page 26: Lista De Control Antes De La Prueba

    Lista de control antes de la prueba Retire cualquier cinta de protecci6n y eti- Inspeccione la moldura de fondo para queta que todavia est6 presente. cerciorarse de que est6 instalada apropiadamente (ver p6gina 11). Revise pare asegurarse de que todos los alambres est6n bien conectados Inspeccione para cerciorarse...
  • Page 27 A ndice de remocion Instrucciones de instalaci6n g de la puerta del horno inferior C6MO REEMPLAZAR LA PUERTA QUITAR LA PUERTA C6MO No se recomienda quitar la puerto inferior parala instalaci6n del producto. Abra la puerta del homo en su totalidad. resione ambas trabas de la bisagra hacia Levante la puerta del abajo en direcci6n del marco de la puerta...
  • Page 28 otas...

Table of Contents