Table of Contents
Advertisement
INSTALLATION SITE
Regarding places for installation
• Is the air conditioner installed at a well-ventilated
place where there are no obstacles around?
• Do not use the air conditioner in the following places.
a. Filled with much mineral oil such as cutting oil
b. Where there is much salt such as a beach area
c. Where sulfured gas exists such as a hot-spring resort
d. Where there are considerable voltage fluctuations
such as a factory or plant
e. Vehicles and vessels
f. Where there is much spray of oil and vapor such as a
cookery, etc.
g. Where there are machines generating electromagnetic
waves
h. Filled with acid and/or alkaline steam or vapor
• Is a snow protection measure taken?
For details, consult your dealer.
Regarding wiring
• All wiring must be performed by an authorized electri-
cian.
To do wiring, ask your dealer. Never do it by yourself.
• Make sure that a separate power supply circuit is pro-
vided for this air conditioner and that all electrical
work is carried out by qualified personnel according
to local laws and regulations.
Pay attention to running noises, too
• Are the following places selected?
a. A place that can sufficiently withstand the weight of the
air conditioner with less running noises and vibrations.
b. A place where the hot wind discharged from the air
outlet of the outdoor unit and the running noises.
• Are you sure that there are no obstacles near the air
outlet of the outdoor unit?
Such obstacles may result in declined performance and
increased running noises.
• If abnormal noises occur in use, consult your dealer.
Regarding drainage of drain pipe
• Is the drain pipe executed to perform complete drain-
age?
If proper drainage is not carried out from the outdoor drain
pipes during air-conditioning operation, chances are that
dust and dirt are clogged in the pipe. This may result in a
water leakage from the indoor unit. Under such circum-
stances, stop the operation of the air conditioner, and then
consult your dealer or our service station.
NAME AND FUNCTION OF EACH SWITCH
AND DISPLAY ON THE REMOTE CON-
TROLLER
Refer to figure 1 on page 3
The illustrations in this operating manual correspond to the
remote control format BRC1C type.
ON/OFF button
1
Press the button and the system will start. Press the
button again and the system will stop.
OPERATION lamp (RED)
2
The lamp lights up during operation.
6
DISPLAY "
CONTROL)
3
When this display shows, the system in UNDER
CENTRALIZED CONTROL.
(This is not a standard specification)
DISPLAY "
" "
" "
TION MODE)
4
This display shows the current OPERATION MODE.
Only for cooling models on which "
played.
DISPLAY "
" (INSPECTION/TEST OPERA-
TEST
TION)
5
When the INSPECTION/TEST OPERATION BUTTON
is pressed, the display shows the system mode is in.
hr
DISPLAY "
" (PROGRAMMED TIME)
hr
6
This display shows PROGRAMMED TIME of the sys-
tem start or stop.
DISPLAY "
" (SET TEMPERATURE)
C
7
This display shows the set temperature.
DISPLAY "
" (FAN SPEED)
L H
8
The display shows the fan speed: "LOW" or "HIGH".
DISPLAY "
" (AIR FLOW FLAP)
9
Refer to page 8.
DISPLAY "
" (TIME TO CLEAN AIR FILTER)
10
Refer to page 9.
DISPLAY "
" (DEFROST/HOT START)
Refer to page 7.
11
"
" is not displayed when the unit is in cooling only
mode.
NON-FUNCTIONING DISPLAY
If that particular function is not available, pressing the
12
button may display the words "NOT AVAILABLE" for a
few seconds.
TIMER MODE START/STOP button
13
Refer to page 8.
TIMER ON/OFF button
14
Refer to page 8.
INSPECTION/TEST OPERATION button
This button is used only by qualified service persons
15
for maintenance purposes.
Do not use it in normal operation.
PROGRAMMING TIME button
16
Use this button for programming "START and/or
STOP" time.
TEMPERATURE SETTING button
17
Use this button for SETTING TEMPERATURE of the
thermostat.
FILTER SIGN RESET button
18
Refer to page 9.
FAN SPEED CONTROL button
19
Press this button to select the fan speed, LOW or
HIGH, of your choice.
" (UNDER CENTRALIZED
" "
" "
" (OPERA-
" is not dis-
Hide quick links:
Advertisement
Table of Contents
