Table of Contents
Advertisement
Quick Links
Part No. 2000491 Rev. A
36" Built-h
Refrigerator
IMPORTANT:
Installer: Leave Installation
Instructions with the Homeowner.
Homeowner: Keep Installation
Instructions for future reference.
Save Installation Instructions for
local electrical inspector's use.
'
IMPORTANT'r.
Read and save
these instructions.
-7-ala
Advertisement
Table of Contents
Related Manuals for KitchenAid 2000491
Summary of Contents for KitchenAid 2000491
- Page 1 Part No. 2000491 Rev. A 36” Built-h Refrigerator IMPORTANT: Installer: Leave Installation Instructions with the Homeowner. Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use. ’ IMPORTANT’r. Read and save these instructions.
-
Page 2: Tools And Materials Needed For Installation
White, Black and Almond, and at least 90°. a stainless steel door panel kit are available from your KitchenAid Because of the weight and size of dealer. Each kit includes door the built-in refrigerator, two or more Floor Damage panels and top grille panels. - Page 3 Dimensions for built-in area Personal Injury/Property Damage Hazard @ Unit is topheavy and may tip fonnrard when the doors are opened. A solid soffii or 2” wood block is Eifxtricfd outlet should be centered required above the refrigerator within shaded area.
-
Page 4: Product Dimensions
The 8-l/2” top grille is provided. maximum extension Smaller top grilles must be ordered II’ levelers (l-114” from your KitchenAid dealer. Check below roilers) the chart below for the part numbers is used to remove you need to order for the size of top... - Page 5 Custom door panels, handle inserts and top grille panels Panel routing for door Refrigerator door panel and lop grille panels. Door and top grille panels: Dimensions shown are with routed + 114” max. 19-l/4”-- edges. Routing is required if panels are more than l/4”...
- Page 6 Side panel requirements +/- I/W tolerance S/32”--+ 23-118” depth rotruding door nstallalioq 118” spacer thickness-) <> 23-7/W’ depth <> flush door 3-314” installation doors/ 132” side irin Refrigerator Side trim when 25” depth is available. If One method is to attach side less than 25”...
-
Page 7: Electrical Requirements
Electrical Water supply 3. Ground electric drill or use a hand requirements drill. Drill a 3/l 6” hole in vertical requirements cold water line. Attach a saddle valve to the water line with a Use only l/4” copper tubing for clamp in an easily accessible water line. -
Page 8: Product Support
Product support E2” A solid soffit or a wood block block(s) is required to prevent the refrigerator from tlpping forward Block(s) must after it Is Installed. extend IO fully cover width Determine what height the of cover. refrigerator will be when it is installed to fit opening. - Page 9 Move refrigerator to Now start... kitchen. Place cardboard or plywood under Remove top grille assembly Personal Injury Hazard refrigerator. Remove appliance package, literature package dolly. Open doors and remove all Because of the weight and and parts bag taped to the packages boxes, parts and packing...
- Page 10 3-prong groundmg Plug side/ power trim supply cord Move refrigerator close to final position. Remove leveling rods cl&wise using a 5/l 6” cardboard or plywood from socket and ratchet until the cabinet under refrigerator. Plug electrical weight is supported by the rear legs. cord into the grounded outlet.
- Page 11 Attach top grille decorative panel built-in refrigerator, read screws. Lift door and bottom hinge assembly to the keyhole bracket on your KitchenAid to desired position. Tighten bottom the frame and pull down to secure. hinge screws and then top hinge If the top grille decorative panel and Care Guide.
- Page 12 If vou need refrigerator does askistance... service... not operate... In the event that your KitchenAid The KitchenAid Consumer appliance should need service, call Assistance Center will answer any Check that the circuit breaker is not the dealer from whom you questions about operating or tripped or house fuse blown.