Advertisement
Installing
Side Burner
and Side Shelf
1. Enlisting the aid of an assistant, attach Side
Burner to tank side of grill. Remove the fasten-
ing strip from burner. Attach Side Shelf to side
opposite tank as shown in Fig. 6a. Align the 4
holes on Side Shelf and Side Burner with the
threaded holes on Grill Head. Tighten securely
using 4 of the 1/4"x3/4" Phillips head screws
provided.
.
3.
Place the Connection
Tube through the slot in
side of Grill Head as illustrated in Fig. 6a.
The Brass Adaptor of the Gas Valve Assembly
(located directly behind the Side Burner control
knob) has 2 threaded fittings. Connect the
Connection Tube from Grill Head to the horizon-
tal fitting. Connect hose end of LP gas regula-
tor to vertical fitting. Tighten both connections
securely with adjustable wrench. See Fig. 6b.
.
Connect the Ignition Wire terminal from Side
Burner with the other from Grill Head. See Fig.
6a. Bind the connected
Ignition Wires and
Connection Tube together using the supplied
Fastening Band.
.
Slide the 5 Tool Hooks onto the Tool Holder
with hooks facing the grill head. Attach Tool
Holder to left side of Side Shelf and secure
firmly using 2 of the M5x0.8x9mm
Phillips head
screws and washers supplied. See Fig. 6c.
Electrode
Check - Requires an Assistant
Before placing the cooking components
into your
grill, ensure that the Spark Electrode Tip is properly
positioned within each Gas Collector Box (a 3-1/4"
wide stainless mechanism found at the front be-
tween each set of burners.) The easiest way to
ensure this is to perform this Electrode Check:
1.
Be sure all Control
Knobs are set to "OFF".
Open the Grill Lid.
.
.
.
Have an assistant
stand behind to the right of
the grill and look down at each Gas Collector
Box. NEVER put your face inside Grill Head.
Press the Ignitor Cap and have the assistant
watch for a small blue spark within each Gas
Collector
Box. tf a spark is present the
Electrode Tips are properly positioned.
If no spark is seen the Spark Gap shown in
Fig. 7 needs to be adjusted
as follows:
Using an adjustable wrench, loosen the Inside Nut
just until the Gas Collector Box can be maneuvered
and turned upward.
•
The gap between the Spark Electrode Tip and
Spark receiver should be approximately
3/16".
If the gap is wider than 3/16" use a pair of long nose
pliers and gently squeeze the Gas Collector Box
until the gap is correct.
Return the Gas Collector Box to its original horizon-
tal position, secure the Inside Nut and try the
Electrode Check again.
Figure
6a
SIDE
SHELF
SLOT FOR
CONNECTION
TUBE
/
SIDE
BURNER
'/
CONNECTION
_
BRASS
TUBE
,,"
_
ADAPTOR
IGNITION
WIRE
_
I
GAS
VALVE
L
FROM
GRILL
HEAD
/
',
FASTENING
I
BAND
IGNITION
WiRE
FROM
SIDE
BURNER
/
S
REGULATOR
WiTH
HOSE
Figure
6b
GAS
VALVE
FOR
SIDE
BURNER
!
ADAPTOR
CONNECTION
TUBEFROM
GRILL
HEAD
REGULATOR
WtTH
HOSE
Figure
6c
TOOL
HOLDER
\
3
TOOLHOOK
/
SIDE
SHELF
Figure
7 - Side View
GAS
COLLECTOR
BOX
/
INSIDE
NUT
10
SPARK
GAP
\
SPARKELECTRODETIP
\
SPARK
RECEIVER
Advertisement
