The Armed System; The Valet Switch - Valet Mode And Override; Easy Valet Tm; Selectable Code Override - Omega Executive ClassicOne Owner's Manual

However, if the security system was activated and reset while you are away, the
disarm confirmation will be 4 horn chirps, and the lights will flash 4 times before staying
on for 30 seconds. The system will have this disarming response until the ignition
switch is turned "on". Also, anytime the security system has been activated, upon
disarming the LED status light will indicate which of the protected zones caused the
activation by flashing a code of numbered flashes between pauses. Again, this
indication remains until the ignition switch is turned "on".
The system may be disarmed without the normal confirmation chirps by pressing
and releasing the transmitter's OPTION button twice within 2 seconds.

The Armed System

When the Model One is armed, the LED status light flashes continuously in a slow
and steady manner. In this state, any violation of a protected entry or optional sensor
will instantly activate, or "trigger" the system. If the system is activated:
- The vehicle's horn or the optional electronic siren will sound. The horn will
repeatedly sound for one second, then pause for one second. Every ten
seconds, the horn will stop sounding completely for 5 seconds; this prevents
the horn from overheating. This audible output will occur for the duration of the
activated cycle. The optional siren, used with the UltraOne, features six different
tones, and every 5 seconds the siren will change the tone to generate more
attention to the vehicle.
- The parking lights will flash on and off repeatedly. The UltraOne will also flash the

The Valet Switch - Valet Mode and Override

The valet switch, which is typically contained within the same housing as the LED
status light, allows the operator to suspend certain functions of the Executive Model
One's normal operations. It is also used in an emergency override disarming of an
armed and activated system, should the transmitter be unavailable or inoperative.
These are two separate and distinct operations: the first is Easy Valet
a disarmed system may be placed into an "off" or "standby" condition (Valet Mode)
without use of the ignition key; the second operation is Selectable Code Override,
which will disarm an armed or activated system and requires the use of the ignition
key. The valet switch is also used in transmitter and features programming operations,
which are described in later sections of this guide.
Easy Valet TM : This unique feature can be utilized anytime the security system
is in the disarmed state. Easy Valet
require the ignition switch to be "on" to enter Valet Mode, but with the Executive Model
One, the ignition can be either "on" or "off", so the ignition key is not required.
Whenever the security system is disarmed, simply press and hold the valet switch
for 1.2 seconds to enter the Valet Mode. The system will confirm it is entered Valet
Mode with two horn chirps, two light flashes and the LED status light will illuminate
and stay on constantly. The system will remain in Valet Mode if the ignition is turned
"on" or "off", or even if the system is disconnected from the vehicle's electrical system.
This is useful for servicing the vehicle; unless in a Valet Mode, the security system
Page - 9
TM
is unique because other security systems
Page - 11
interior lights.
- The doors will relock. If opened, relocking will occur when the door is closed.
The horn will sound and lights will flash for 60 seconds, unless you disarm the
system with the transmitter by pressing the UNLOCK button. If needed, the valet
switch and ignition key may be used to disarm the system (Selectable Code Override;
pages 12-14). Please note that while the system is activated, pressing the UNLOCK
button will only disarm the system, and not unlock the doors; simply press UNLOCK
again to unlock the doors.
If all protected entries are secure at the end of 60 seconds, the system will stop
itself and rearm automatically to detect another entry attempt. If there is a protected
entry still open, or a sensor still in a violated state at the end of 60 seconds, the system
will reactivate for two more 60 second cycles. If this occurs, the system will still stop
itself after a total of 3 minutes and rearm automatically, and ignore the open entry or
violated sensor circuit while protecting the other circuits. Should the entry be closed
or the sensor return to normal, protection will be reinstated for the affected circuit.
After the security system is activated and it reset itself, the confirmation upon
disarming will no longer be the normal two horn chirps, and the lights flashing twice
and staying on for 30 seconds. Instead, the system will have 4 horn chirps and the
lights will flash 4 times before staying on for 30 seconds. Anytime the system is
activated, the LED Status Light will change to flashing two to five times between
pauses, indicating which protected zone activated the system. The LED Status Light
will continue flashing this Violation Code until the ignition key is turned "on".
will return to its previous state when power and ground are first applied, such as when
reconnecting a battery. If the system was disarmed when power is removed, it will
activate very briefly, then disarm, when power is restored.
While in the Valet Mode, the remote transmitters can still operate the panic feature,
the power door locks, and the trunk release, if so equipped. Valet Mode prevents the
system's alarm from being armed; using the transmitter to lock the doors will not arm
TM
, whereby
the system, nor will it engage the starter interrupt. When the transmitter is used to
lock and unlock the doors when the system is in Valet Mode, there will be light flash
confirmations, but no audible chirps unless the system is programmed to do so. In
addition to the constantly illuminated LED status light, the system will chirp the horn
twice as a reminder of Valet Mode when the ignition switch is turned off. Additionally,
the doors will lock when the ignition is turned "on" and unlock when it is turned "off"',
if the system is programmed to do so. To remove the system from the Valet Mode,
simply momentarily press the valet switch. The system will instantly revert to the
disarmed condition. To confirm that the system has exited the Valet Mode, the LED
status light will be extinguished. Remember, Easy Valet
system is disarmed - an armed state requires using the Selectable Code Override.
How to Disarm the System Without Using the Transmitter
Selectable Code Override: In the event the transmitter is lost, damaged, or it
is otherwise inoperable, the valet switch and your ignition key may be used to disarm
the system. Selectable Code Override offers a high level of security because, in
Page - 10
TM only operates when the
Page - 12