Stealth Cam STC-AC540IR Instruction Manual page 6

Setting the Time Out Mode in PIR operation mode:
Your Stealth Cam can be programmed to set the amount of time in
seconds or minutes the camera will sleep between PIR triggers.
•
Switch the camera to the ON position.
LCD screen will display the camera status screen.
•
Press the [MENU] button once within 30 seconds to enter the
programming mode.
•
The word PIR will be blinking, press [OK] to confirm the camera
operation by PIR detection.
•
Press [UP] button FOUR times to enter Time Out setting mode.
•
The word TIME OUT will be blinking.
•
Press [OK] button and the SECONDS digits will be blinking.
•
Press [UP] or [DN] button to increase or decrease the time value
in seconds from 0 to 59 seconds in 1 second increments.
•
Press [OK] to save the seconds setting and the MINUTES digits will
be blinking.
•
Press [UP] or [DN] button to increase or decrease the time value
in minutes from 0 to 59 minutes in 1 minute increments.
•
Press [OK] to save the minutes setting.
•
You'll then see the word ‐ TIME ‐ blinking.
•
Press [MENU] button to exit.
www.stealthcam.com
Toll Free 877-269-8490
•
Press [OK] to save your selection and enter Day setting.
•
The Day digits will be blinking.
•
Press [UP] or [DN] to increase or decrease the Day value.
(01 – 31).
•
Press [OK] to confirm the Date setting and enter Year setting.
•
The YEAR digits will be blinking.
•
Press [UP] or [DN] to increase or decrease the Year value.
(01 – 99).
•
Once this is all done, press [OK].
•
You'll then see the word ‐ dEL ‐ blinking.
•
Press [MENU] button to exit the program setting and back to the
status screen.
www.stealthcam.com
Toll Free 877-269-8490
Setting the Time and Date in PIR operation mode:
Your Stealth Cam uses the 24hr military time format.
•
Switch the camera to the ON position.
LCD screen will display the camera status screen.
•
Press the [MENU] button within 30 seconds to enter the
programming mode.
•
The word PIR will be blinking, press OK to confirm the camera
operation by PIR detection.
•
Press [DOWN] button TWO times to enter Time and Date mode.
•
The word TIME will be blinking.
•
Press [OK] to enter Minute setting first.
•
The MINUTE digits will be blinking.
•
Press [UP] or [DN] to increase or decrease the minute value
(00 – 59).
•
Press [OK] to save your selection and enter Hour setting.
•
The HOUR digits will be blinking.
•
Press [UP] or [DN] to increase or decrease the hour value
(00 – 23).
•
Press [OK] to save your selection and enter Month setting.
•
The Month digits will be blinking.
•
Press [UP] or [DN] to increase or decrease the Month value.
(1 ‐ 12).
www.stealthcam.com
21
Toll Free 877-269-8490
Setting the Time Lapse Mode:
FIRST, you need to make sure the Program Control Switch is in the
CUSTOM position. The Time Lapse Default setting value is from 18:00
to 8:00 the next day. When the camera is set to time lapse mode, the
program setting will bypass any PIR activation. Instead, the user can
set the program for a pre‐determined time period [such as 6:00 to
18:00]. The user then sets the frequency of pictures only (NOT videos)
during this time period [such as one picture every 10 seconds]. The
camera will remain in Time Lapse mode until the user has changed the
program setting.
•
Switch the camera to the ON position.
LCD screen will display the camera status screen.
•
Press the [MENU] button once within 30 seconds to enter the
programming mode.
•
Press [UP] button until you see the
word tLS blinking.
•
Press [OK] to confirm and go into TLS
Mode "Start Time" setting.
•
The display will show TIME + S 88:88
(S = Start, 88:88 = time in HH:MM)
•
Press [OK] to set the "Start Time"
setting. At this point you can adjust the
time from 00:00 to 23:59.
•
The MINUTE digits will be blinking.
www.stealthcam.com
23
Toll Free 877-269-8490
22
24