Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, Universal Serial Bus...
Contact Address: TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618-1697 Telephone: (949) 583-3000 EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC and/or R&TTE Directive 1999/5/EC...
Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.
Page 6
ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency.
Page 7
Disposing of the computer and the computer’s batteries ■ Discard this computer in accordance with applicable laws and regulations. For further information, contact your local government. ■ This computer contains rechargeable batteries. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them.
This manual tells how to set up and begin using your TOSHIBA NB300 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 5, Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power and Power-up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program.
Page 14
Preface When procedures require an action such as clicking an icon or entering text, the icon's name or the text you are to type in is represented in the typeface you see to the left. Display Names of windows or icons or text generated by the computer that appear on its display screen are presented in the type face you see to the left.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
General Precautions Creating a computer-friendly environment Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer. Leave enough space around the computer and other equipment to provide adequate ventilation.
General Precautions Pressure or impact damage Do not apply heavy pressure to the computer or subject it to any form of strong impact as this can damage the computer's components or otherwise cause it to malfunction. Mobile phones Please be aware that the use of mobile phones can interfere with the audio system.
Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Page 19
TOSHIBA Assist ■ TOSHIBA eco Utility ■ Online Manual ■ TOSHIBA NB300 series User's Manual (This manual) Documentation ■ TOSHIBA NB300 Series User Information Guide ■ Instruction Manual for Safety and Comfort If any of the items are missing or damaged, contact your dealer immediately.
Built-in Your computer is equipped with one processor and processor type varies depending on model. To check which type of processor is included in your model, open the TOSHIBA PC Diagnostic Tool Utility by clicking Start All programs TOSHIBA Utilities PC Diagnostic Tool.
Introduction Disks Hard disk drive This computer supports SATA 3.0Gbps and is equipped with one of the following hard disk drive (HDD) types. The capacity of each hard disk drive model is different. ■ ■ 160GB ■ 250GB Please note that part of the hard disk drives overall capacity is reserved as administration space.
Page 22
You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.
Page 23
Introduction Headphone jack This jack lets you connect speakers or a stereo headphone. When you connect an external speaker or headphones, the internal speaker is automatically disabled. Microphone jack A 3.5mm mini microphone jack enables connection of a three-conductor mini jack for stereo microphone input, and connection of a stereo device for audio input.
Page 24
Windows 7 is available. Refer to the preinstalled Software section at the front of this chapter. TOSHIBA Utilities A number of utilities and drivers are preinstalled to make your computer more convenient to use. Refer to the Utilities and Applications section in this chapter.
Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use. Access each function using the following procedures. *1 To access the Power Options, click Start Control Panel...
Page 26
Refer to the Using the Using the Hard Disk Drive (HDD) Protection section in Chapter 4, Operating Basics for details. The TOSHIBA HDD Protection function does not guarantee that the hard disk drive will not be damaged. User’s Manual...
Page 27
Windows 7 operating system and it works for all USB ports. TOSHIBA PC Health The TOSHIBA PC Health Monitor software Monitor program monitors computer system functions such as power consumption, the cooling system and HDD Drop sensor. It alerts users of specific system conditions via pop-up messages.
Introduction TOSHIBA Value Added Package TOSHIBA Flash The TOSHIBA Flash Cards provide a quick way Cards to modify selected system functions and to launch applications. ■ Hot key function ■ TOSHIBA utility launcher function TOSHIBA Power TOSHIBA Power Saver provides you with the...
For further information on their operation, please refer to each utility's online manual, help files or README.TXT file. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities that improve the ease and control of communication devices and network connections, help in the...
Introduction Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory kit PC2-5300 (DDR2-667) or compatible 1GB or 2GB memory module can easily be installed in the computer.
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The following figure shows the computer’s front with its display panel in the closed position.
Page 32
The Grand Tour DC IN The DC IN indicator normally glows green when power is being correctly supplied from the AC power adaptor. However, If the output voltage from the adaptor is abnormal, or if the computer's power supply malfunctions, this indicator will go out.
The Grand Tour Arrow Lock When the Arrow indicator lights green, you can use the dark gray labeled keys on the keypad overlay as cursor keys. Numeric Lock When the Numeric Lock indicator glows green, you can use the dark gray labelled keys on the keypad overlay for numeric input.
Page 34
The Grand Tour Do not block the thermal vent holes. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
The Grand Tour Right side The following figure shows the computer’s right side. 1. Headphone jack 2. Microphone jack 3. Universal Serial Bus (2.0) port 4. DC IN 19V jack 5. Security lock slot Figure 2-4 The right side of the computer Headphone jack A standard 3.5 mm mini headphone jack enables connection of stereo headphones or other device...
The Grand Tour Back side Figure 2-5 shows the computer’s back side. Figure 2-5 The computer’s back side. Underside The following figure shows the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage.
Page 37
The Grand Tour Memory module slot The memory module slot is located here. The memory module slot allows for the replacement with an additional memory module. Please refer to the Additional memory module section in Chapter 8, Optional Devices for more information.
The Grand Tour Front with the display open This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you. 1. Microphone 2.
Page 39
You can use it for video chatting or video conferencing using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.
The Grand Tour Keyboard indicators When the CAPS LOCK indicator glows, the keyboard will produce capitals when any letter is typed. 1. CAPS LOCK indicator Figure 2-8 Keypad indicators CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. User’s Manual 2-10...
Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury.
Chapter 3 Getting Started This chapter provides basic information to start using your computer. It covers the following topics: ■ All users should be sure to read the section Starting up for the first time. ■ Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer.
Page 43
Getting Started ■ Use a anti-virus software and make sure it is updated regularly. ■ Never format storage media without checking its content - formatting destroys all stored data. ■ It is a good idea to periodically back up the internal hard disk drive or other main storage device to external media.
■ Always use the TOSHIBA AC adaptor that was included with your computer or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury.
Page 45
Getting Started 1. Connect the power cord to the AC adaptor. Figure 3-1 Connecting the power cord to the AC adaptor (2-pin plug) Figure 3-2 Connecting the power cord to the AC adaptor (3-pin plug) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model.
Getting Started Opening the display The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity.
Page 47
Getting Started ■ When opening the panel, please be careful not to force it beyond the point where it moves easily. ■ Be careful not to open the display panel too far as this could put stress on the display panel’s hinges and cause damage. ■...
Getting Started Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Power-up Modes for more information.
Getting Started Turning off the power The power can be turned off in one of three modes, either Shut Down Mode, Hibernation Mode or Sleep Mode. Shut Down Mode When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system's main screen the next time it is turned on.
Getting Started ■ You can return to your previous working environment immediately when you turn on the computer. ■ Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature.
Getting Started Turning Off Your Computer where Electronic Devices are Regulated or Controlled. When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always shut down the computer completely or put the computer into Hibernation mode instead of allowing it to go into Sleep mode.
Getting Started 3. Press the power button. This feature must be enabled. Refer to the Power Options in the Control Panel. When you turn the power back on, you can continue where you left when you shut down the computer. ■...
Page 53
Getting Started System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes tools to repair startup problems, run diagnostics or restore the system. See the Windows Help and Support content for more information about Startup Repair.
Page 54
Getting Started A recovery image of the software on your computer is stored on the hard disk drive, and can be copied to either DVD or USB Flash Memory by using the following steps: 1. Select either blank DVD or USB Flash Memory. 2.
Page 55
2. While holding down F12 key on the keyboard, turn on your computer - when TOSHIBA Leading Innovation>>> appears, release the F12 key. 3. Use the up and down cursor keys to select either "optical disc drive" or "USB Flash Memory"...
Chapter 4 Operating Basics This chapter describes the basic operations of your computer and highlights the precautions that should be taken when using it. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
Operating Basics The two buttons below the Touch Pad are used like the buttons on a standard mouse - press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right button to display a menu or other function depending on the software you are using.
Page 58
Starting the USB Sleep and Charge Utility To start the utility, click Start All Programs TOSHIBA Utilities USB Sleep and Charge. You can set Typical Mode/Alternate Mode/Disable USB sleep and charge function also in BIOS Setup menu.
CD Player' function to record music to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW media. ■ Do not use the 'Disc Backup' function of TOSHIBA Disc Creator in order to copy DVD Video or DVD-ROM material that has copyright protection. ■...
TOSHIBA Disc Creator cannot record in packet format. ■ You might not be able to use the 'Disc Backup' function of TOSHIBA Disc Creator to back up a DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW disc that was made with other software on a different optical media recorder.
Operating Basics Using the web camera Built-in web camera is provided with some models. This section describes the bundled webcam utility, which can capture still and video images. The web camera will auto-run when Windows starts. Ensure that you remove the protective plastic film that covers the Web Camera before using it.
Operating Basics Using TOSHIBA Web Camera Application TOSHIBA Web Camera Application is pre-configured to start when you turn ® 7; if you need to restart it go to Start → All Programs → on Windows TOSHIBA → Utilities → Web Camera Application.
Operating Basics Using the microphone You can use the built-in or an external microphone that connects to the microphone jack to record sounds into your applications. It can also be used to issue voice commands to applications that support such functions. Since your computer has a microphone and speaker, “feedback”...
■ TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. Bluetooth wireless technology Bluetooth™...
Operating Basics Enable/Disable Wireless communication with hot key You can enable or disable Wireless communication (Wireless LAN, Bluetooth) functions, with hot keys (FN + F8). No transmissions are sent or received when wireless communication is turned off. ■ Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields.
Operating Basics The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). This section describes how to connect/disconnect to a LAN. Do not install or remove a memory module while Wake-up on LAN is enabled.
Operating Basics 1. LAN jack 2. LAN cable Figure 4-4 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector or router. Check with your LAN administrator and hardware or software vendor before using or configuring a network connection. Disconnecting the LAN cable To disconnect the LAN cable, follow the steps as detailed below: 1.
Operating Basics Using the cleaning cloth The cleaning cloth can be used to wipe away dust and fingerprints from the keyboard and palm rest area of your computer. ■ When wiping the keyboard, palm rest and display panel, do so gently without using excessive pressure.
The TOSHIBA HDD Protection function does not guarantee that the hard disk drive will not be damaged. When vibration is detected, a message will be displayed on the screen, and the icon in the Taskbar notification area will changed to the protection state.
TOSHIBA HDD Protection is active. The hard disk drive head is in a safe position. TOSHIBA HDD Protection is disabled. TOSHIBA HDD Protection Properties You can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection window. To open the window, click Start Programs TOSHIBA Utilities HDD Protection Settings.
Page 71
Intensely shaking the computer or other subjecting it to strong impacts may cause damage to the computer. Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.
Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the 104/105-key enhanced keyboard functions can be performed on the computer. The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages.
Soft keys: FN key combinations The FN (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
The Keyboard Press FN + F10 or FN + F11 to access the computer's integrated keypad. When activated, the keys with grey markings on their bottom edge become either numeric keypad keys (FN + F11) or cursor control keys (FN + F10). Please refer to the Keypad overlay section in this chapter for more...
Page 75
The Keyboard Sleep: Pressing FN + F3 switches the system to Sleep mode. Hibernate: Pressing FN + F4 switches the system to Hibernation mode. Output: Pressing FN + F5 changes the active display device. Brightness (Down): Pressing FN + F6 decreases the computer's display panel brightness in individual steps.
Volume up: Pressing FN + 4 to increase the volume in increments. FN Sticky key You can use the TOSHIBA Accessibility Utility to make the FN key sticky, that is, you can press it once, release it, and then press an "F Number"...
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows Start Button activates the Start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows Start menu. This key has the same function as the secondary (right) mouse button.
The Keyboard Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard functions without having to turn the overlay off: 1. Hold FN and press any other key - this key will operate as if the overlay were off.
The Keyboard Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation, but you are able to generate these characters using their specific ASCII codes. With the overlay on: 1. Hold down ALT. 2. Using the overlay keys, type the ASCII code of the character you require.
Chapter 6 Power and Power-up Modes The computer's power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power-up modes. Power conditions The computer's operating capability and battery charge status are affected by different power conditions, including whether an AC adaptor is...
Power and Power-up Modes Table 6-1 Power conditions continued Power on Power off (no operation) Battery charge • Operates adaptor is above low • LED: Battery off battery trigger DC IN off connected point Battery charge • Operates is below low •...
Power and Power-up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected - the following indicator conditions should be noted: Indicates the AC adaptor is connected and is Green correctly supplying power to the computer. Under any other conditions, the indicator does not No light light.
Press <F1> to resume, <F2> to Setup. The computer's RTC battery is a lithium battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.
The battery pack is lithium ion battery, which can explode if not replaced, used, handled or disposed of properly. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius.
Power and Power-up Modes Use only the computer connected to an AC power source to charge the battery pack. Never attempt to charge the battery pack with any other charger. Time The following table shows the approximate time required to fully charge a discharged battery.
Power and Power-up Modes In such cases you should follow the steps as detailed below: 1. Fully discharge the battery by leaving it in the computer with the power on until the system automatically turns itself off. 2. Connect the AC adaptor to the DC IN 19V jack of the computer, and to a wall outlet that is supplying power.
Power and Power-up Modes ■ The environmental temperature - operating time decreases at low temperatures. ■ The condition of the battery terminals - you should always ensure the terminals stay clean by wiping them with a clean dry cloth before installing the battery pack.
Power and Power-up Modes ■ Disconnect the AC adaptor when the battery is fully charged - overcharging will make the battery hot and can shorten its operating life. ■ If you are not going to use the computer for more than eight hours, disconnect the AC adaptor.
Page 89
Power and Power-up Modes 5. Slide the battery safety lock towards the release ( ) position to make the battery release latch movable. 1. Battery safety lock 2. Battery release latch 3. Battery pack Figure 6-1 Releasing the battery pack (1) 6.
Page 90
Power and Power-up Modes To install a battery, follow the steps as detailed below: 1. Insert the battery pack as far as it will go into the computer (1). 2. Ensure that the battery pack is securely in place and the battery safety lock (2) is in its position.
Power and Power-up Modes TOSHIBA Password Utility The TOSHIBA Supervisor Password Utility allows you to maintain an additional level of security and provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Supervisor Password Utility are different from ®...
Power and Power-up Modes If you enter the password incorrectly three consecutive times, the computer shuts down. You must turn on the computer again and re-enter the password. Power-up modes The computer has three power-up modes: ■ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode.
TOSHIBA HW Setup allows you to configure settings for General, Password, Display, Boot Priority, Keyboard, USB, LAN. If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
HW Setup and Passwords This window displays the BIOS version and contains two buttons: Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. When finish BIOS update, please restart your computer and press F2 into BIOS setup manual and load BIOS default one time.
HW Setup and Passwords If they do not match, the following message appears. You must repeat step 1. Incorrect Password!!! If you enter the password incorrectly three times in a row, the computer will shut down. You will not be able to access the password option in the HW Setup. In this case you must turn the power off and back on to retry the procedure.
HW Setup and Passwords Enabled Enables the USB Legacy Emulation. (Default) Disabled Disables the USB Legacy Emulation. Wake-up on LAN This feature lets the computer’s power be turned on from shutdown when it receives awake-up packet ( Magic packet ) from the LAN. Regarding Wake-up on LAN from sleep or hibernation, you must check the "Allow the device to wake the computer"...
Chapter 8 Optional Devices Optional devices can expand the computer's capabilities and its versatility. This chapter describes the connection or installation of the following devices: To connect optional devices (such as USB device or External monitor) to the computer, be sure to check the shape and orientation of the connector before connecting.
Optional Devices Bridge media slot The computer is equipped with a Bridge media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants.
Page 99
Optional Devices ■ The SD memory card logo is ( ■ The SDHC memory card logo is ( ■ The maximum capacity of SD memory cards is 2GB. The maximum capacity of SDHC memory cards is 32GB. Card Type Capacities 8MB, 16MB, 32MB, 64MB, 128MB, 256MB, 512MB, 1GB, 2GB SDHC...
When installing or removing a memory module, you must ensure that you do not touch any other internal areas of the computer. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions.
Page 101
Optional Devices 3. Turn the computer upside down and remove the battery pack - refer to Replacing the battery pack section in Chapter 6, Power and Power-up Modes, if required. 4. Loosen the screw securing the memory module cover. 1. memory module cover Figure 8-2 Removing the memory module cover 5.
Optional Devices ■ Never allow metal objects, such as screws, staples and paper clips, to enter the computer or keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. ■...
Optional Devices 2. Turn the computer upside down and remove the battery pack (refer to Chapter 6, Power and Power-up Modes.) 3. Remove one screw securing the memory module cover. 4. Lift off the memory module cover. 5. Push the latches outward and the memory module will pop up. 6.
Optional Devices External monitor An external analog monitor can be connected to the computer's external monitor port. In order to connect a monitor, follow the steps as detailed below: 1. Connect the monitor cable to the external monitor port . 1.
Optional Devices Connecting the security lock In order to connect a security cable to the computer, follow the steps as detailed below: 1. Turn the computer so its right hand side faces you. 2. Align the security cable with the 'lock hole' and secure it in place. 1.
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.
When the computer starts up, the self-test will be run automatically, and the following will be displayed: TOSHIBA Leading Innovation>>> This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system.
Troubleshooting Depending on how the Boot Priority is set in the Hardware Setup, the computer tries to load first from drive A then from drive C, or first from drive C then from drive A. If any of the following conditions are present, the self test failed: ■...
Page 110
Troubleshooting Battery If you suspect a problem with the battery, check the DC IN and the battery indicator. For information on indicators and battery operation see Chapter Power and Power-up Modes. Problem Procedure Battery doesn’t power The battery may be discharged - connect the AC the computer adaptor to recharge the battery.
Page 111
Troubleshooting Password Problem Procedure Cannot enter Refer to the HW Setup Window section in password Chapter 7, HW Setup and Passwords. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard and Chapter 7, HW Setup Passwords.
Troubleshooting Hard disk drive Problem Procedure Computer does not Check if a diskette is in the diskette drive or a boot from hard disk CD/DVD is in the optical disc drive. Remove any drive diskette and/or CD/DVD and check the Boot priority settings.
Troubleshooting Problem Procedure The mouse pointer Try changing the speed setting in the mouse moves too fast or too control utility. slow 1. Click Start Control Panel Hardware and Sound Mouse to access the mouse control utility. 2. Click the Pointer Options tab. 3.
Page 114
Troubleshooting SD/MuliMedia Card Refer also to Chapter 8, Optional Devices. Problem Procedure Memory card error Reseat the memory card to make sure it is firmly occurs connected. Check the card’s documentation. You cannot write to the Make sure the card is not write protected. memory card You cannot read a file Make sure the target file is on the memory card...
Troubleshooting Sound system Problem Procedure No sound is heard Check the software volume settings. Make sure the headphone connection is secure. Check Sound Preferences. Make sure the sound function is enabled and that settings for I/O address, Interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you may have connected to the computer.
Page 116
Check the "USB Sleep and Charge" check box to enable this function in the TOSHIBA USB Sleep and Charge Utility. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons.
Page 117
TOSHIBA USB Sleep and Charge Utility. The "USB WakeUp When "USB Sleep and Charge function" is function" does not enabled in the TOSHIBA USB Sleep and Charge work Utility, the "USB WakeUp function" does not work for ports that support the USB Sleep and Charge function.
Page 118
Troubleshooting Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN hub. Wake-up on LAN Make sure the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off. If problems persist, consult your LAN administrator.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system so it is important that you investigate other sources of assistance first.
Page 120
Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed on the below. Outside of Europe Europe Australia Germany & Austria TOSHIBA Australia Pty. Ltd.
5°C to 35°C (41°F to 95°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - please refer to your PC documentation or visit the Toshiba website at www.pcsupport.toshiba.com for details).
Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Legal Footnotes Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Graphics Processor Unit (GPU) Graphics processor unit (GPU) performance may vary depending on product model, design configuration, applications, power management settings and features utilized.
Page 124
Appendixes Table of Contents Specifications................A-1 Appendix A Display Controller................. B-1 Appendix B Wireless LAN................. C-1 Appendix C AC Power Cord and Connectors..........D-1 Appendix D TOSHIBA PC Health Monitor ............E-1 Appendix E User’s Manual Appendixes-1...
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size With 3 cell 266(w) x 192.3(d) X 24.2(front) x 30.8(rear) Battery millimeters (not including parts that extend beyond the main body) With 6 cell 266(w) x 192.3(d) X 24.2(front) x 36.4(rear) Battery millimeters (not including parts that extend beyond the main body)
Appendix B Display Controller Display controller The display controller interprets software commands into hardware com- mands that turn particular pixels on or off. A high-resolution external monitor connected to the computer can display up to 1400 horizontal and 1050 vertical pixels at up to 16M colors. The display controller also controls the video mode, which uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed on screen.
Appendix C Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card Specifications ■ Mini Card Form Factor ■ IEEE 802.11 Standard for (Revision b,g and n) Compatibility Wireless LANs ■...
Subject to the radio regulations that apply in your country/region, your Wireless LAN card may support a different set of 2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for infor- mation about the radio regulations that apply in your country/region.
Page 130
Table Wireless IEEE 802.11 Channels Sets (Revision b,g and n) Frequency Range Channel ID 2400-2483.5 MHz 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457* 2462 2467* 2472* When installing Wireless LAN cards, the channel configuration is managed as follows: ■...
Appendix D AC Power Cord and Connectors The AC input plug of power cord must be compatible with various interna- tional AC power outlets. Power cords need to meet the local standards and the specifications listed as below: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm Current rating:...
Certification agencies Europe: Austria: Italy: Belgium: CEBEC The Netherlands: KEMA Denmark: DEMKO Norway: NEMKO Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: Germany: United Kingdom: Outside of Europe: U.S. and Canada: UL listed and CSA certified No. 18 AWG, Type SVT or SPT-2 China: CCC, CQC India:...
Page 133
United Kingdom UL approved BS approved Australia Europe AS approved Approved by the appropriate agency Canada China CSA approved CCC approved User’s Manual...
Page 134
■ This information is used to identify and provide a notification of system conditions which may effect the performance of your Toshiba computer. It may also be used to help diagnose problems should the computer require service by Toshiba or Toshiba's authorized service providers.
■ Once enabled, you may disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Uninstall a program in the Control Panel. Doing so will automatically delete all collected information from the HDD. ■ The TOSHIBA PC Health Monitor software does not extend or modify Toshiba's obligations under its standard limited warranty in any way.
Page 136
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AACS: advanced access content system AC: Alternating current ACPI: Advanced Configuration and Power Interface ASCII: American Standard Code for Information Interchange BIOS: basic input/output system bps: bits per second CD: compact disc...
Page 137
Glossary IDE: integrated drive electronics IEEE: Institute of Electrical and Electronics Engineers I/O: input/output IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LAN: local area network LCD: liquid crystal display LED: light emitting diode MB: megabyte MMC: multi media card OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect...
Page 138
Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. application: A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing and games.
Page 139
Glossary byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computer's main memory.
Page 140
Glossary components: Elements or parts (of a system) which make up the whole (system). Composite Video (YUV): A standard video signal used to transmit images, e.g. from a VCR to a TV. computer program: A set of instructions written for a computer that enable it to achieve a desired result.
Page 141
Glossary Digital Audio: An audio compression standard that enables high-quality transmission and real-time playback of sound files. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk.
Page 142
(FDD): An electromechanical device that reads and writes to floppy diskettes. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
Page 143
Glossary gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also megabyte. graphics: Drawings, pictures, or other images, such as charts or graphs, to present information. hard disk: A storage device composed of a rigid platter or platters that can be magnetically coded with data.
Page 144
Glossary I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. I/O devices: Equipment used to communicate with the computer and transfer data to and from it. IrDA 1.1: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps.
Page 145
Glossary memory: Typically refers to the computer's main memory, where programs are run and data is temporarily stored and processed. Memory can be volatile and hold data temporarily, such as RAM, or it can be nonvolatile and hold data permanently, such as ROM. A computer's main memory is RAM.
Page 146
The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver: A TOSHIBA utility that lets you set the parameters for various power-saving functions. program: A set of instructions a computer can execute that enables it to achieve a desired result.
Page 147
A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): Volatile memory that can be written to as well as read.
Page 148
TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. USB: Universal Serial Bus. This serial interface lets you communicate with several devices connected in a chain to a single port on the computer.
Page 149
Glossary window: A portion of the screen that can display its own application, document or dialog box. Often used to mean a Microsoft Windows window. Wireless LAN: Local Area Network (LAN) through wireless communication. write protection: A method for protecting a floppy diskette from accidental erasure.