Fx Mix - American Audio Pro-Scratch 2 User Manual

EFFECTS - FX MIX
FX MIX MODE:
This function allows you to use the effects to transfer from one track to another, one track to
a sample, or one sample to another. FX Mix uses the effects and the FLASH BUTTONS (8). The FX Mix func-
tion will only work with samples and cue points programmed in the any of the three FLASH BUTTONS (8). The
procedure below list the steps to activate the FX Mix Mode. In the following example we will you the SKID Effect
to transfer from one track to a programmed sample.
OFF
POWER
ON
1 2 3 4 5 6 7 8 9 0 AUTO
PROGRAM NONSTOP
CUE BPM
KEY
CUE ELAPSED TOTAL REMAIN
PARAMETER TIME BEAT SYNC. LOCK
SINGLE
LOOP
BPM
RELOOP
T M S F PITCH
PARAMETER RATIO
SCRATCH FILTER HOLD ECHO TRANS
FX SELECT
TIME
SKID PHASE FLANGER PAN
TEMPO
LOCK
BOP
SAMPLE PITCH
FX
MIX
ENTER
STEP TWO:
After you have activated FX Mix Mode, select an effect. In this
example we will choose the SKID Effect. Choosing the SKID Effect we create a
braking effect.
OFF
POWER
ON
1 2 3 4 5 6 7 8 9 0 AUTO
PROGRAM NONSTOP
CUE BPM
KEY
CUE ELAPSED TOTAL REMAIN
PARAMETER TIME BEAT SYNC. LOCK
SINGLE
LOOP
BPM
RELOOP
T M S F PITCH
PARAMETER RATIO
SCRATCH FILTER HOLD ECHO TRANS
FX SELECT
TIME
SKID PHASE FLANGER PAN
TEMPO
LOCK
BOP
SAMPLE PITCH
FX
MIX
ENTER
STEP FOUR: To initiate the FX Mix , tap the BOP/ENTER BUTTON (30). At this
point you may continue the FX with the current track. If you follow steps one and
four, you will initiate the FX mix on the current track. For example; If you used the
brake effect for your effects mix, following steps one and four will initiate a brake
effect in current track and then continue with the track once the brake effect has
ended. You must be in continuos play mode for this effect to operate properly.
EJECT
STEP ONE: Be sure you have created a sample and stored it in to the
SGL/CTN
FLASH 3 BUTTON (8) (see creating a sample on page). After a sample
REV.PLAY
ON/OFF
4%/8%/16%
has been created and stored, begin playback on
BUTTON (13) to activate the FX Mix Mode.
Figure 57
EJECT
SGL/CTN
REV.PLAY
STEP THREE:
ON/OFF
4%/8%/16%
sample, press the FLASH BUTTON 3 (8).
will now end the current track and beginning to play the sample stored in the Flash
3 bank. The track will end in a brake effect and then immediately being to play you
stored sample in Flash Bank 3.
Figure 59
American Audio - www.americandj.com - Pro-Scratch 2™ Instruction Manual Page 30
© ®
When you are at the point in the track you wish to begin the
a track. Select the FX MIX
OFF
POWER ON
1 2 3 4 5 6 7 8 9 0
CUE
PARAMETER TIME
SINGLE
LOOP
RELOOP
PARAMETER RATIO
SCRATCH
SKID
FX
MIX
Figure 58
Pressing the
FLASH BUTTON 3 (8)
OFF
POWER ON
1 2 3 4 5 6 7 8 9 0
CUE
PARAMETER TIME
SINGLE
LOOP
RELOOP
PARAMETER RATIO
SCRATCH
SKID
FX
MIX
Figure 60
AUTO
PROGRAM NONSTOP
CUE BPM
KEY
ELAPSED TOTAL REMAIN
BEAT SYNC. LOCK
EJECT
BPM
T M S F PITCH
FILTER HOLD ECHO TRANS
FX SELECT SGL/CTN
TIME REV.PLAY
PHASE FLANGER PAN
TEMPO ON/OFF
LOCK 4%/8%/16%
BOP
SAMPLE PITCH
ENTER
AUTO
PROGRAM NONSTOP
CUE BPM KEY
ELAPSED TOTAL REMAIN BEAT SYNC.
LOCK
EJECT
BPM
T PITCH
M S F
FILTER HOLD ECHO TRANS
FX SELECT SGL/CTN
TIME REV.PLAY
PHASE FLANGER PAN
TEMPO ON/OFF
LOCK 4%/8%/16%
BOP
SAMPLE PITCH
ENTER