Table of Contents
Advertisement
Installation and Operation Instructions for the following unitized outdoor camera models:
UNI-ONER / EP SERIES
Outdoor High PoE Clear Dome
UNI-ONER580C7
UNI-ONER550C7
UNI-ONER520C7
UNI-ONEP580C7
UNI-ONEP550C7
UNI-ONEP520C7
Note: To maximize power for the camera and heater option, the unit requires that you
calibrate the enclosure. This calibration process is shown starting with instruction
block 18. During calibration, the onboard processor intelligently determines the
maximum safe power output of the midspan, and ensures that the enclosure does
not exceed that limit. Once calibration is complete the required values are stored in
permanent memory, with no additional calibration required.
Note: Please note that to achieve the increased depth with the aspheric design for optimal
camera lens to capsule orientation, the capsule is slightly angled around the highest
section. This creates a "line', visible to the naked eye, around the upper most section
of the capsule. This "line" serves as the geometric center line used to insure proper
camera placement. It is not typically seen by the camera. However, this line maybe
visible in the camera image when camera's above horizon tilt capability is used.
Unitized SNC-ER580 pendant type, clear dome, with heater and blower
Unitized SNC-ER550 pendant type, clear dome, with heater and blower
Unitized SNC-ER520 pendant type, clear dome, with heater and blower
Unitized SNC-EP580 pendant type, clear dome, with heater and blower
Unitized SNC-EP550 pendant type, clear dome, with heater and blower
Unitized SNC-EP520 pendant type, clear dome, with heater and blower
81-IN6712 06152012
Advertisement
Table of Contents
Related Manuals for Sony UNI-ONEP520C7
Summary of Contents for Sony UNI-ONEP520C7
- Page 1 Installation and Operation Instructions for the following unitized outdoor camera models: UNI-ONER / EP SERIES Outdoor High PoE Clear Dome UNI-ONER580C7 Unitized SNC-ER580 pendant type, clear dome, with heater and blower UNI-ONER550C7 Unitized SNC-ER550 pendant type, clear dome, with heater and blower UNI-ONER520C7 Unitized SNC-ER520 pendant type, clear dome, with heater and blower UNI-ONEP580C7...
-
Page 2: Important Safeguards
à presença de instruções importantes na literatura que acompanha o dispositivo. If technical support or service is needed, contact Sony at the following number: Questo simbolo del punto del exclamaton è inteso per avvertire l’utente alla presenza delle istruzioni importanti nella letteratura che accompagna l’apparecchio. -
Page 3: Electrical Specifications
Contents of Box Electrical Specifications UNI-ONER/EP Power POE 56V Input Power: 100 to 240Vac (Midspan) Power: 1.3A Frequency: 50 to 60 HZ output Camera: POE (56Vdc) Heater: 56Vdc (max. 40W) English Energía de entrada: 100 a 240Vac (Midspan) Energía: 1.3A Frecuencia: 50 a 60 hertzios de salida Cámara: POE (56Vdc) Calentador: 56Vdc (máximo 40W) - Page 4 Mounting Preparation Securely attach pendant pipe or the UNI-WMB1 Wrap Teflon tape around the pipe threads (See block 9 when using UNI-WMB3). Pull wiring through pipe and position grommet as shown. to ensure a tight seal. • Con seguridad pipa pendiente de la fijación o el UNI-WMB1 (véase el bloque 9 para UNI-WMB3).
- Page 5 Loop the lanyard over the set screw to Complete wiring by connecting the temporarily hold housing. RJ45 cable. • Loop el cordón sobre el tornillo de fijación para mantener • Completar cableado conectando el Cable RJ45. temporalmente de la vivienda. •...
- Page 6 UNI-WMB3 If using external ¾” (27mm) conduit attach Install the wall mount bracket to a wall or appropriate hardware. adapter bracket. • Si usa conducto del ¾ (27mm) externo el” ata apropiado • Instale el soporte del montaje de la pared a la pared o soporte hardware.
- Page 7 UNI-WMB3 Continued Feed wiring into wall mount, UNDO lanyard and connect housing to wall complete connections. mount coupling. • Cableado de la alimentación en el montaje de la pared, • DESHAGA el acollador y conecte la cubierta con el acoplador conexiones completas.
- Page 8 CALIBRATION BUTTON Internal view, note the location of the Secure the bolts with the provided calibration button. Allen wrench. • Vista interior, tenga en cuenta la ubicación del • Asegure los pernos con la llave Allen proporcionada. botón de calibración. •...
- Page 9 Before After Align the arrows on the outside of the Loop the lanyard around the tab inside dome and lock. the housing. • Alinee las flechas en el exterior de la bóveda y trábese. • Coloque el acollador alrededor de la lengüeta •...
-
Page 10: Materials Needed
How - to Clean a Dome Bubble To effectively clean your video surveillance dome bubble (acrylic or polycarbonate) from debris, follow these simple step-by-step instructions. Materials Needed • Clean, dry, pressurized air • Water • High quality soft paper towel •... -
Page 11: Replacement Parts List
Replacement Parts List Part Number Description SDO180W PENDENT COUPLING (WHITE) RPFD2612 HOUSING TOP GASKET RPFD709 HOUSING TOP RP70VL2008 POE POWER PCB RPFD702 24VAC HEATER RPFD060 CAMERA BRACKET RPPKH6063 SPACERS RPFDO80 12VDC BLOWER RPLEDR02 RP70SW07 CALIBRATION SWITCH RPVL4138 PLASTIC CAP RPVL4101 QUICK RELEASE BRACKET CAMERA RPFD703... - Page 12 Available Mounting Accessories UNI-WMB1 UNI-WMB3 UNI-WMBB1 UNI-RMB1 UNI-CMA1 UNI-PMA1 Aluminum Gooseneck Wall Mount Aluminum Corner Aluminum Existing Pole / Wall Mount Parapet Mount Wall Mount Bracket Mount Adaptor Pole Mount Adaptor UNI-WMB1 UNI-WMB3 Wall Mount Wall Mount Bracket Mounting Accessories Needed: Mounting Accessories Needed: •...
- Page 13 Warranty For warranty information on this and other Sony Security Systems Products, please visit: http://pro.sony.com/bbsccms/services/files/servicesprograms/SecurityWarranty.pdf...