Sony Ipela SNC-ER585 Installation Manual page 2


How to install the camera
1
Dome cover
a
Screws (6)
O-ring
Camera
b
2, 3
Mounting arm
(not supplied)
Bolts
Wire
Wire-fixing belt
bracket
Shield tape
(not supplied)
Cable
Nuts
Coupling
4
Locking screws (2)
Bolts (3)
Top unit
5
Waterproof
seal
Locking
screws (2)
Top unit
6
Bolts (2)
Top unit
7
a
Harness
band
Harness
mount
Release
button
Always have the stopper side
face down and tie the cables.
b
Band mount
100 mm to 125 mm
Harness band
(4 inches to 5 inches)
Cable
8
c
Keep parallel
9, 10
Fall-
prevention
Top unit
wire
Align the triangular
and square marks
Camera
O-ring
11
Bolts (3)
Top unit
Camera
12
Top sunshades
13, 14
Top sunshade
Align the triangular marks

ø222 (8 3 / )
4
Unit: mm (inches)
Installation
Notes

Do not allow water to come in contact with the power cable, connection
cables or connectors, as it may cause water leakage into this device, and
subsequent damage.

The mounting arm (not supplied) to which the device is attached should have
fixing screws of NPT 1 1/2" specified by a Sony dealer. Using an unspecified
mounting arm may cause water leakage into this device, and subsequent
damage. Be sure to use the specified mounting arm.
 The lens zoom and angle may result in a blurred or inclined image within the
range above the horizon of the lens position.
 To prevent the dome cover from damage and stain, do not remove the
protecting sheet from the dome cover until the setting is completed.
Warning

If installing the camera in high location, such as high wall, entrust the
installation to a professional contractor or service personnel.
 The camera should be securely installed on a location strong enough to
support the weight of the camera and the mounting arm. Otherwise, the
camera and mounting arm may fall and cause serious injury.
 For the fall-prevention of the camera, make sure to use the wire rope.
 If the bolts are attached loosely or loosen, the camera and parts may fall. There
may also be a risk of water leakage. Make sure to tighten the bolts and screws
so that they will not loosen.
 Check the camera is attached securely, the screws, etc. are not loosened
periodically, at the least once a year. Depending on the usage conditions,
periodic inspections should be conducted more frequently.
Note
Use the supplied screws to install the unit. Using other screws may cause
damage inside the unit.
a
How to Install
Before installation
Referring to the installation manual of the mounting arm (not supplied), drill the
required holes for the mounting screws and the connection cable. Then install
b
the mount arm in advance. After that, wrap the screw part of the mounting arm
in a shield tape (not supplied).
How to install the camera
1
Attach the dome cover to the camera. (a)
Tighten the six screws in the specified order (1 to 6). (b)
Notes

Remove the drafting tape from the O-ring before attaching the dome
cover.

Be sure to properly place the O-ring in the groove firmly before attaching
the dome cover. If the O-ring is not properly and firmly placed, waterproof
performance may be compromised.

The six screws should be tightened to 1.2 N•m.
2
Attach the supplied wire-fixing belt and wire bracket to the mounting arm
(not supplied). Then secure the wire-fixing belt and wire bracket to the
mounting arm by tightening two nuts.
Note
The two bolts should be tightened to 5.2 N•m.
3
Screw the supplied coupling on the mounting arm.
Note
If the coupling is attached loosely or loosens, the camera may fall. Securely
put the coupling around the mounting arm so that it will not loosen.
4
Remove the three bolts from the top part of the camera, and turn the top unit
until it stops, then pull it upward to remove it from the camera.
Have a 5 mm ( / inch) hex wrench ready to loosen the bolts.
7
32
5
Attach the top unit to the mounting arm.
Place the locking screws fixed to the top unit in the groove of the coupling
and turn the top unit until it stops, in the direction of the arrow.
Notes

Remove the drafting tape from the waterproof seal before attaching the
mounting arm.
 Be sure to verify that the locking screws are not loose. If the locking screws
are loose, the camera may fall. The locking screws should be tightened to
5.2 N•m.
 Be sure to tighten the waterproof seal properly to the top unit before
attaching; otherwise, waterproof performance may be compromised.
6
Attach the two supplied bolts to the screw holes of the coupling and tighten
them.
Note
The two bolts should be tightened to 5.2 N•m.
7
Run the supplied harness band through the band-mounting hole (a), tie the
cables at 100 mm to 125 mm (4 inches to 5 inches) from the cable head (b).
If the tied position is not appropriate, push the release button of the harness
band to loosen, and tie the cables again.
8
Secure the band mount to the harness holder (a), and connect the cables.
Push the cables into the top unit (b).
Be sure that all cable connection sides of the top unit are in parallel with the
harness holder. (c)
9
Hook the fall-prevention wire of the camera on the hole of the wire bracket.
10
Align the triangular mark of the camera and square mark of the top unit and
push the camera into the top unit. Then turn the camera until it stops, in the
direction of the arrow.
Notes

Be sure to properly place the O-ring in the groove firmly before attaching
the camera. If the O-ring is not properly and firmly placed, waterproof
performance may be compromised.

Be sure that the camera connection terminal of the top unit is in parallel
with the harness holder before pushing the camera into the top unit.

To prevent the cables from getting caught, push the slack part of the
cables into the top unit before attaching the camera.
11
Attach the camera to the top unit using the three bolts which were removed
in step 4.
Note
The three bolts should be tightened to 5.2 N•m.
12
Separate the provided top sunshade and reattach the separated parts above
the camera to return the top sunshade to its original form.
Notes
 Run the fall-prevention wire through the top sunshade.
 Securely attach the top sunshade so that the snap hook will not get caught
in it.
13
Align the respective triangular marks of the camera and top sunshade and
Screw push the top sunshade into the camera. Then turn the sunshade until it stops,
in the direction of the arrow.
14
Secure the camera and top sunshade using the screw on the top sunshade.
Notes
 Please make sure to attach the top sunshade. The top sunshade prevents
the device from overheating in direct sunlight.
 The screw should be tightened to 1.2 N•m.
Removing the camera
1
Remove the one screw that secures the top sunshade to the camera in Step
14 of "How to install the camera" to remove the top sunshade.
2
Remove the three bolts used in Step 11 of "How to install the camera. "
3
Turn the top unit to the position where the triangular mark of the camera and
the square mark of the top unit align, and pull the camera out downwards.
4
Remove the fall-prevention wire of the camera from the hole of the wire
bracket.
Connection
Connecting to the Network
Connect the LAN port of the camera unit to a router or hub in the network using
the network cable (not supplied).
Connecting the Power Source
The following method is available for connecting to a power source.

24 V AC
Connecting to a 24 V AC power source supply
Connect the 24 V AC power supply system to the power input terminal of the
camera. The AC power cable is not supplied.

Use a 24 V AC power source isolated commercial power supply.

The usable voltage range is as follows:
24 V AC: 21.6 to 26.4 V

Use a UL cable (VW-1 style 10368) for 24 V AC connection.
Note
Always connect pin 2 (center) to the ground terminal.
Recommended power cable
24 V AC
Cable(AWG) #22 #20
Maximum
cable length
5 (16.4) 8 (26.2)
(m (feet))
Connecting the I/O Cable
Wiring diagram for sensor input
Mechanical switch/open collector output device
Camera inside Outside
3.3 V
10 kohms
2.2 kohms
5 or 6 pin
10 kohms
(Sensor Input 1 or 2)
Mechanical
switch
10 kohms
7 or 12 pin
GND
GND GND GND

Wiring diagram for alarm output
Camera inside Outside
24 V DC
R
2 pin
(Alarm Output +)
Magnet relay
24 V AC Circuit example
24 V DC,
1 A or less
1 pin
(Alarm Output –)
GND
Specifications
Compression
Video compression format JPEG/MPEG4/H.264
Audio compression format G.711/G.726 (40,32,24,16 kbps)
Maximum frame rate 30 fps
Camera
Image device 1/2.8 type Exmor CMOS
Synchronising Internal
Minimum illumination 1.7 lx (Shutter speed: 1/30 sec,
Exposure: Full auto, 50IRE [IP])
Video S/N 50 dB (Gain 0 dB)
Lens
Focus length f=4.3 mm to 129.0 mm
Maximum relative aperture F1.6 to F4.7
Minimum object distance 300 mm
Mechanism
Pan 360°, endless rotation
Maximum speed: 300°/s
Tilt 210° (with auto invert function)
Maximum speed: 300°/s
Interface
LAN 10BASE-T/100BASE-TX, auto negotiation (RJ-45)
I/O Input/Output Sensor input: × 2, make contact
Alarm output: × 1, 24 V AC/DC, 1 A
(mechanical relay outputs electrically isolated
from the camera)
SD memory card slot
Microphone input Minijack (monaural)
Plug-in-power supported (rated voltage: 2.5 V
DC)
Recommended load impedance 2.2 kohms
Line output Minijack (monaural), Maximum output level:
1 Vrms
Others
Power supply 24 V AC ± 10%, 50 Hz/60 Hz
Power consumption SNC-ER585
Max. 76 W
SNC-ER585H
Max. 26 W
Operating temperature SNC-ER585
–40 °C to +60 °C (–40 °F to 140 °F)
Activation temperature range: –40 °C to
+60 °C (–40 °F to 140 °F)
SNC-ER585H
Maximum temperature range: –5 °C to +65 °C
(23 °F to 149 °F) (2 hours use)
Continuous use temperature range: –5 °C to
+60 °C (23 °F to 140 °F)
Activation temperature range: 0 °C to +65 °C
(32 °F to 149 °F)
Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
Operating humidity 20% to 80%
Storage humidity 20% to 95%
Dimensions (Diameter/Height) 
ø222 mm × 324.1 mm (ø8
12 7 / inches) (Not including the projecting
8
parts)
Mass Approx. 4.3 kg (9 lb 8 oz)
Supplied accessories Dome cover (1)
Top sunshade (1)
Coupling (1)
Wire-fixing belt (1)
Wire bracket (1)
Bolts (2)
Power supply connector 3-pin (1)
I/O harness 14-pin (1)
Harness band (1)
Band mount (1)
Installation manual (1 set)
CD-ROM (User's Guide, supplied programs) (1)
Design and specifications are subject to change without notice.
Recommendation of Periodic Inspections
In case using this device over an extended period of time, please have it
inspected periodically for safe use.
It may appear flawless, but the components may have deteriorated over
time, which may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony
dealer.
#18 #16
15 (49.2) 21 (68.9)
or
Open collector
output device
3 / inches ×
4