Advertisement
Mounting the pads and the trigger module on the
rack system
Mount the pads and the trigger module on the rack system. Then position the
kick pad and the hi-hat.
Mounting the TP65 (Drum pads) on the rack system
Figure 8: Pads Assembly-1
Figure 9: TP65
!1 Clamp bolt
!2 TP65 (Rear side)
1
See Figure 9.
!1
!2
Attach the clamp bolts (
) on TP65s (
) . Tighten the clamp bolts fi ve to six turns each.
Figure 10: Pads Assembly-2
2
See Figure 10.
Loosen the knob (shown with
) of the tom holder
on the middle left. Move the tom
holder inward as shown in the close-up illustration (m). Then tighten the knob and attach
the tom holder
fi rmly at a position where it points slightly downward.
Figure 11: Tom Holder and Drum Pad
!3 Tom holder
!4 Clamp bolt
3
Attach the TP65 (Drum pad) to the tom holder
as shown in Figure 11. Tighten the clamp
bolt and attach the drum pad TP65 fi rmly.
4
See Figure 10 again. Loosen the knob (shown with
) of the tom holder
left. Move the tom holder inward as shown in the close-up illustration (n). Then tighten the
knob and attach the tom holder
fi rmly at a position where it points slightly downward.
5
Attach the TP65 (Drum pad) to the tom holder
. Tighten the clamp bolt and attach the
drum pad TP65 fi rmly.
6
Repeat step 4 and 5 in the same manner for tom holders
and
at the center of the rack
system and for tom holder
on the right, and attach the TP65 (Drum pad) to each tom
holder.
Mounting the PCY65 (Cymbal pads) on the rack system
Figure 12: Pads Assembly-3
Figure 13: Cymbal holder-1
@1 Cymbal holder
@2 Wing nut
@3 Felt washer
1
@2
@3
See Figure 13. Remove the wing nut (
) and one of the felt washers (
) from the cymbal
holder (
@4
) .
Figure 14: Cymbal holder-2
@4 PCY65 (Cymbal pad)
2
@4
Attach the PCY65 (Cymbal pad) (
) to the cymbal holder (
@3
@2
the felt washer (
) and the wing nut (
) removed in step 1, and tighten it.
Turn the wing nut until you are certain that the cymbal pad is attached. The cymbal pad is
designed to shake when you hit the surface, even when the wing nut is tightened securely.
Mounting the DTXPL (Trigger module)
Figure 15: Pads Assembly-4
Figure 16: Module stand-1
1
@6
See Figure 16. Loosen the knob of the clamp (
) (shown with
@5
@6
stand (
) from the clamp (
) .
Figure 17: Module stand-2
@7 Fastening screw*
@8 DTXPL (Rear side)
*
Th e fastening screws are included in the same plastic bag that includes the Assembly Manual of rack system
RS40. Th e plastic bag is packaged between the space within the cardboards used for cushioning.
2
@7
Tighten the fastening screws (
) with a Phillips screwdriver, as shown in Figure 17, to
@5
attach the module stand (
) onto the rear side of the trigger module (
Figure 18: Module stand and clamp
3
@9
#0
Attach the module stand (
) onto the clamp (
position.
Assembling the KP65 (Kick pad)
1
If a drum mat (sold separately) is not available, lay a cardboard on the fl oor to prevent
scratching the surface.
Figure 19: KP65 Assembly
on the upper
#3 Body
#4 Base
#5 Wing bolt
#6 Spring washer
#7 Washer
2
#5
#6
Remove the wing bolt (
) , the spring washer (
and keep the four sets nearby in the order removed.
* If the wing bolt, the spring washer and/or the washer are separated from each other, set
them as illustrated in Figure 19-(a).
3
#4
#3
Set the base (
) on the body (
) , and attach them using the wing bolt, the spring washer
and the washer removed in step 2.
Assembling the FP6110A (Foot pedal)
1
If a drum mat (sold separately) is not available, lay a cardboard on the fl oor to prevent
scratching the surface.
Figure 20: FP6110A Assembly
2
$3
Insert the radius rod (
) into the hole of the frame as shown in Figure 20.
3
$1
Insert the beater (
) into the hole of the beater attachment part until the further end of the
beater slides outward about 15 mm. Tighten the beater locking bolt (
$4
(
) .
@1
Attaching the FP6110A (Foot pedal) to KP65 (Kick pad)
) as shown in Figure 14. Attach
Figure 21: FP6110A and KP65
%1 FP6110A (Foot pedal)
%2 KP65 (Kick pad)
%3 T-handlet bolt
1
Turn the T-handlet bolt (
@5 Module stand
loosen it.
@6 Clamp
Figure 23: Attaching FP6110A
) and remove the module
@8
) .
Installing the HH65(Hi-hat controller) and KP65 (Kick pad)
Figure 25: Hi-Hat and KP65
@9 DTXPL + Module stand
#0 Clamp
#1 Knob
#1
) . Tighten the knob (
) and fi x the
Connecting the pads to the Trigger Module
Connect the output jacks of the pad and the input jacks of the trigger module
with the 9-channel snake cable.
Figure 26: DTXPL (Rear panel)
#7
#3
Figure 27: 9-channel Snake Cable
) and the washer (
) from the body (
) ,
*
Each straight plug is labeled indicating the input jacks to which they are to be connected.
1
Insert the straight plugs (Figure 27-(a)) of the 9-channel snake cable into the input jacks on
the rear panel of the trigger module. For standard assembly, connect the straight plugs to
the input jacks in accordance with the indication on each label.
$1 Beater
$2 Beater locking bolt
$3 Radius rod
$4 Drum key
$2
) using the drum key
Figure 28: Diagram of standard connection
Figure 22: T-handlet bolt
%3
%1
) of the foot pedal (
) in a counterclockwise direction and
Figure 24: Adjustment
%4 Hoop clamp
%5 Convex part
%6 Beater head
%7 Pedal
2
%5
Attach the convex part (
) of the kick pad to the
%4
hoop clamp (
) .
3
%3
Turn the T-handlet bolt (
) in a clockwise direction
and tighten it.
4
Step on the pedal and check if the head of the beater
2
hits the center area of the kick pad. Adjust the length
of the beater and/or position the pedal to the right or
left if necessary.
1
Connect the AC adaptor to the DTXPL.
If a drum mat (sold separately) is not available,
Figure 29: Power switch (DTXPL rear panel)
lay a cardboard on the fl oor to prevent
scratching the surface.
2
^2
Place the HH65 (Hi-hat controller) (
) under
^1
the TP65 (Hi-hat cymbal) (
) .
3
Place the KP65 (Kick pad) with FP6110A (Foot
^3
&1 Power supply jack (DC IN 12V)
pedal) (
) at the bottom center of the RS40
(rack system).
&2 Cable clip
&3 Power switch
^1 TP65 (Hi-hat cymbal)
^2 HH65 (Hi-hat controller)
^3 KP65 (Kick pad)+ FP6110A (Foot pedal)
Figure 30: Cable clip (DTXPL rear panel)
ON
Figure 31: Using Cable Band
*
Insert the L-shaped plugs (Figure 27-(b)) of the 9-channel snake cable into each
corresponding pad. It is recommended to connect the cables in order from numbers
o
shown in Figure 28 (from the shortest cable to the longest cable).
Connecting to a power source
ON
1
Make sure to turn the power off (the Standby/
&3
On switch (
) is set to the standby position).
2
Attach the AC adaptor to connect to a power
source.
Insert the DC plug into the power supply jack
&1
(
) and twist the cable around the cable clip
&2
(
) to prevent the DC plug from falling out.
3
Use the cable bands to bind the cables to the
pipes at the six points shown with the circles.
* Leaving the cable slacked may inter-
fere with your performance.
The assembly is now completed.
To check the actual sound, connect the unit with an amplifi ed speaker or a headphone before turning on the
power.
U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
©2009 Yamaha Corporation
WS41160 ********.*-****
Printed in Indonesia
q
to
Advertisement
