Table of Contents
Advertisement
Troubleshooting
Troubleshooting
Possible causes
No power.
i The battery has run out.
i The AC power adapter plug has come out
of the power outlet.
i The battery is loaded backward.
i The battery cover is not closed correctly.
Power cuts out during
The battery has run out.
operation.
Battery runs out quickly.
i Camera is used in extremely cold
conditions.
i The terminals are soiled.
i The battery can no longer be recharged.
i The xD-Picture Card or internal memory
No photograph is taken
when
pressing
the
is full.
shutter button.
i The xD-Picture Card or internal memory
is not formatted.
i The xD-Picture Card contact area is
soiled.
i The xD-Picture Card is damaged.
i The Auto power off function has turned the
camera off.
i The battery has run out.
Cannot use the flash.
i The shutter button was pressed while the
flash was charging.
i The battery has run out.
i Photography mode is set to "
Ù
"
".
i Continuous shooting is selected.
The flash settings are
The Photography mode is set to "AUTO",
restricted and cannot be
"
,
", "
.
", "
©
", "
Ö
selected.
The playback image is
i The subject is too far away.
dark even though the
flash was used.
i Your finger was covering the flash.
i The lens is dirty.
The image is blurred.
i You photographed scenery with Macro
mode selected.
i You took a close-up shot without selecting
Macro mode.
i You are shooting a subject that is not
suited to autofocusing.
There is speckling on
The picture was taken with a slow shutter
the image.
speed (long exposure) in a high-temperature
environment.
i The camera volume is set too low.
The camera does not
emit any sound.
i The microphone was blocked during
shooting/recording.
i There is something covering the speaker
during playback.
Frame erase does not
Some frames may be protected.
erase the frame.
The
ERASE
ALL
function does not erase
all the frames.
The COPY ALL function
The internal memory or xD-Picture Card is
does not copy all the
full.
frames.
106
eIf you think the camera is faulty, check the following once more.
Solutions
i Load a new or fully charged battery.
i Plug the adapter back in.
i Load the battery in the correct direction.
i Close the battery cover correctly.
Load a new or fully charged battery.
i Put the battery in your pocket or another
warm place to heat it and then load it into
the camera just before you take a picture.
i Wipe the battery terminals with a clean,
dry cloth.
i Load a new or fully charged battery.
i Insert a new xD-Picture Card or erase
some unnecessary frames.
i Format the xD-Picture Card or internal
memory on the camera.
i Wipe the xD-Picture Card contact area
with a clean dry cloth.
i Insert a new xD-Picture Card.
i Turn the camera on.
i Load a new or fully charged battery.
i Wait until the charging is completed before
pressing the shutter button.
i Load a new or fully charged battery.
,
ÿ
i Change the Photography mode.
", "
" or
i Set continuous shooting to "OFF".
The flash settings are restricted because the
", "
ÿ
", "
Ÿ
", "
Ù
" or "
Õ
".
camera settings are tailored to the scene
being shot. Change the Photography mode
for a wider range of flash settings.
i Move to within the effective flash range
before taking the picture.
i Hold the camera correctly.
i Clean the lens.
i Cancel Macro mode.
i Select Macro mode.
i Use AF/AE lock to take the picture.
This is a characteristic of CCDs and does
not indicate a camera fault.
i Adjust the volume.
i Take care not to block the microphone
during shooting/recording.
i Make sure that the speaker is uncovered.
Unprotect frames using the camera on
which the protection was first applied.
Insert a new xD-Picture Card or erase
some unnecessary frames.
Troubleshooting
Possible causes
Screens
are
not
A language other than English is selected in
ô
displayed in English.
the "
"
setting in the "
UP menu (➡P.76).
There is no image or
i The included A/V cable was connected
sound on the TV.
during movie playback.
i The camera is not connected to the TV
correctly.
i "TV" is selected as the TV input.
i The "
õ
" video output setting is incorrect.
i The TV volume is turned down.
The TV image is black
The "
õ
" video output setting is incorrect.
and white.
When connecting the
i The USB cable (included) is not correctly
camera to a PC, the
connected to the PC or camera.
photographed image or
i The PC is not turned on.
playback image appears
on the camera's LCD
monitor.
i Camera malfunction.
Nothing happens when
using the Mode switch.
i The battery has run out.
The camera no longer
The camera has suffered an unforeseen
works correctly.
problem.
®
Cannot
print
with
"
" PICTBRIDGE is not selected in "
˜
PictBridge.
USB mode in the "
" SET-UP menu.
The
camera
was
connected to a PC
when the USB mode
®
was set to "
".
Solutions
1Press the "MENU/OK" button to display
˜
" SET-
the menu.
˜
2Press "
a
" or "
b
" to select "
" SET-UP
and press "
".
c
ô
3Press "
a
" or "
b
" to select "
"
4Press "
c
".
5Press "
a
" or "
b
" to select "ENGLISH".
6Press the "MENU/OK" button.
i After the movie playback mode is stopped,
connect the camera and TV correctly.
i Connect the camera and TV correctly.
i Set the TV input to "VIDEO".
i Change the setting to "NTSC" or "PAL"
(➡P.76).
i Adjust the volume.
Change the setting to "NTSC" or "PAL"
(➡P.76).
i Set up the camera, and connect the USB
cable (included) correctly.
i Turn the PC on.
i Briefly remove the battery or disconnect
the AC power adapter. Then reload the
battery or reconnect the AC power adapter
and try again.
i Load a new or fully charged battery.
Briefly remove the battery or disconnect the
AC power adapter. Then reload the battery
or reconnect the AC power adapter and try
again. If you think the camera is faulty,
contact your FUJIFILM dealer.
ò
®
ò
"
Select "
" PICTBRIDGE in "
" USB
˜
mode in the "
" SET-UP menu.
Perform steps 1 to 3 to remove the
camera from the PC.
h Windows
1 The "New Hardware Found" wizard or
"Scanner and Camera" wizard appears. If
the wizard does not appear, proceed to
step 3.
2 Click the [Cancel] button.
3 Disconnect the camera from the PC.
h Macintosh
1 The window for locating the driver
appears. If the window does not appear,
proceed to step 3.
2 Click the [Cancel] button.
3 Disconnect the camera from the
Macintosh.
107
Advertisement
Table of Contents
