Table of Contents
Advertisement
Command No.
(OP, AB, RB)
75(D5, 0, 3)
T_READ_RSSI_I
76(D6, 3, 0)
T_WRITE_RSSI_I
77(D7, 0, 3)
T_READ_TEMP_I
78(D8, 0, 3)
T_READ_HDET_I
79(D9, 1, 0)
T_BUZZER_ON_I
80(DA, 0, 0)
T_BUZZER_OFF_I
81(E3, 0, 0)
T_VOC_PCMLPON_I
82(E4, 0, 0)
T_VOC_PCMLPOFF_I
84(E6, 3, 0)
T_WR_CD_TXLIMIT_I
85(E7, 0, 0)
T_SPEAKER_ON_I
86(E8, 0, 0)
T_SPEAKER_OFF_I
87(E9, 0, 0)
T_FM_LOOP_TEST_I
88(EA, 0, 0)
T_TRK_ADJ_I
89(EB, 3, 0)
T_CDTRK_ADJ_I
90(F0, 3, 0)
T_FM_HIGH_CH_PWR_I
91(F0, 3, 0)
T_FM_LOW_CH_PWR_I
92(F2, 3, 0)
T_FM_TX_PWR_2_I
93(F3, 3, 0)
T_FM_TX_PWR_3_I
94(F4, 3, 0)
T_FM_TX_PWR_4_I
95(F5, 3, 0)
T_FM_TX_PWR_5_I
96(F6, 3, 0)
T_FM_TX_PWR_6_I
97(F7, 3, 0)
T_FM_TX_PWR_7_I
99(F9, 3, 0)
T_FM_MOST_CH_PWR_I
100(FF, 3, 0)
T_MAX_I
The AB (Input Argument Byte Number) values of these commands are used only in the manual test. In
1)
automatic test mode, the AB is regarded as 0.
You can assign the value for these commands. If the AB value is assigned without argument, the test is
2)
achieved with the value stored in EEPROM.
After you get a desired test value by performing these commands, if you want to save the value into
3)
EEPROM, use T-SAVE-VAL-I command to store the test value into the corresponding position.
OP: Operation Command Number
AB: Input Argument Byte Number
RB: Return Byte Number
SAT 32, 33 are not operating in MSM2 CHIP test
46 command is required in Rx, and Tx path test at FM mode
Samsung Electronics - Contents may change without notice.
Signal. Name
3)
3)
2)
2)3)
3)
2)3)
2)3)
2)3)
2)3)
2)3)
2)3)
Description
Read a RSSI.
Writes RSSI value.
Read Temp.
Read High Detect.
Buzzer On at DTMF 0 key.
Buzzer Off.
Play a PCM LOOP BACK.
Play off a PCM LOOP BACK.
Turn on the speaker path.
Turn off the speaker path.
Play a PCM FM loopback.
FM TRK_LO_ADJ control.
CDMA TRK _LO_ADJ control.
Compensated value for high chan PWR.
Compensated value for low chan PWR.
Setting the volume for Power Level 2.
Setting the volume for Power Level 3.
Setting the volume for Power Level 4.
Setting the volume for Power Level 5.
Setting the volume for Power Level 6.
Setting the volume for Power Level 7.
Compensated value for Power Level 2.
Compensated value for Most chan PWR.
Circuit Description
6-13
Advertisement
Table of Contents
