Table of Contents
Advertisement
Condenser Tumble Dryer
VL9000
Table of Contents
Before using the dryer
Name of Parts....................................1
Important Safety Instructions .....2-3
Installation....................................4-10
Preparation .....................................11
How to operate the dryer
Control panel..............................12-13
Programming guide.........................14
Drying methods ...............................15
Maintenance
Cleaning and maintenance .......16-17
Trouble shooting .......................18-19
Wiring circuit ..................................20
Specifications .................................21
Name of Parts
Container handle
Front grill
Ground terminal
Rear footplate
Warning
Read all instructions before using dryer.
Dryers are provided with operating,care and in-
stallation instructions
SAVE THESE INSTRUCTIONS
This diagram may be slightly different from the layout of the machine you have just
purchased due to techincal improvements
1
Program selector
Door
Back plate
Back cover board
Drainage outlet
Advertisement
Table of Contents
Summary of Contents for THOR THOR VL9000
-
Page 1: Table Of Contents
Name of Parts Program selector Container handle Condenser Tumble Dryer VL9000 Door Table of Contents Before using the dryer Name of Parts........1 Front grill Important Safety Instructions ..2-3 Installation........4-10 Preparation ........11 Back plate Ground terminal How to operate the dryer Control panel......12-13 Programming guide......14 Back cover board... -
Page 2: Important Safety Instructions
Important Safety Instructions Important Safety Instructions To reduce the risk of fire, electrical shock, or injury to 15.The dryer must only be used for its intended purposed. persons when using this dryer, follow basic precautions,including 16. Do not sit on top of the dryer. the following: 17.If the cord is damaged,it must be replaced by the manufacturer ,its service agent 1.Read all instructions before using this dryer. -
Page 3: Installation
Installation Installation Dimensions Change the door-opening direction 33-1/2′′ If the direction of the dryer's door is not suitable to the location, its opening direction 24-3/8′′ may be changed. The procedure is as follows: 23-7/16′′ Weight =95lbs. Packing accessories Checklist of the accessories and materials provided with the machine: Owner's Certificate of Terminal block... -
Page 4: Wire Cord Connections
Installation Installation ELECTRICAL CONNECTIONS 3-Wire Cord Connections 1.This appliance must be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. 2.Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt, creating electric shock and/or fire hazard. - Page 5 Installation Installation 3. Thread a U.L. approved 30 Amp power cord, NEMA 14-30 type ST or SRDT 4-Wire Cord Connections through the strain relief. 4. Attached the green power cord ground wire to the cabinet with green ground screw. 5. Attached the white (neutral) power cord conductor from the power cord and the green ground wire from the dryer harness to the silver-colored center terminal on the terminal block.
-
Page 6: Preparation
Installation Preparation Drain switchover Attention Before use, clean any deposits from inside the drum of the dryer with During the drying of the laundry, the condensate water is automatically a wet towel; collected in a box inside the machine. The water needs to Clean debris on the filter screen to increase the drying efficiency. -
Page 7: Control Panel
Control Panel Control Panel G - Program progress display Depending on the program selected, the drying stage reached is shown by the indicator light on the control panel: - Drying - Ready to iron - Airing - End/Anti-crease At the end of a program,the End/Anti-crease indicator light comes on. A - Program knob The drum will continue to rotate at intervals to prevent laundry creasing, if you Turn this knob to choose the drying program you desire. -
Page 8: Programming Guide
Programming Guide Drying Methods Type of Laundry 1.Turning on power Max. load Program Degree of drying Insert the power plug into an appropriate wall socket and turn on the power. Operating power supply: (220-240)V/60Hz. COTTON Heavy cotton fabrics, sheets, Very dry Extra dry 15.4lbs. -
Page 9: Cleaning And Maintenance
Cleaning and Maintenance Cleaning and Maintenance 1 Cleaning the surface -Using a coin or other tool, push the slides on the cover to the position Wipe the body of the dryer and the control panel with a damp cloth. as shown in the figure and then remove the cover; Remember not use any organic solvent or corrosive agent to avoid -Turn the condenser's handle 90 degrees in the direction as shown in damage to the machine. -
Page 10: Trouble Shooting
Trouble Shooting Trouble Shooting Prompt and Alarm Information In case of an improper operation or trouble with the machine when it operates, the code corresponding to the trouble will be displayed on the screen: Cause Code Category Solutions There is no change in Contact a professional Trouble code the temperatures of... -
Page 11: Wiring Circuit
Wiring Circuit Specifications Type VL9000 Item Item K1 NTC K1 NTC (220-240)V/60Hz Power supply Maximum operating current(A) Drying program PCB1 PCB1 PCB2 PCB2 2800 Maximum power(W) Dimensions(H×D×W) 33-1/2′′x24-3/8′′x23-7/16′′ IPX4 Waterproof level R1-Heating1 R2-Heating2 T1-Non-self-restting thermal cut-out T2-Thermostat K1-Door switch K2-Level switch K3-Power switch H-Humidity sensor NTC-Temperature sensor PS-Drainage pump M-Motor PCB1 PCB2-Printed circuit board...