Page 1
INSTRUCTION MANUAL Color Television 29U9FS 29X9FS P/N:48586789E208-R0...
Page 2
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”...
IMPORTANT SAFEGUARDS PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR TELEVISION EQUIP- MENT AND RETAIN FOR FUTURE REFERENCE. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE TV RECEIVER. 1 Read all of these instructions. 7 Slots and openings in the cabinet and the back or bottom are provided for ventilation 2 Save these instructions for later use.
Page 4
(f) When the television equipment exhibits 13 An outside antenna system should not be located in the vicinity of overhead power a distinct change in performance - this lines or other electric light or power indicates a need for service. circuits, or where it can fall into such 18 When replacement parts are required, be power lines or circuits.
CONTENTS PREPARATION •CONNECTING ANTENNA •NAME OF EACH PART BASIC TIPS FOR OPERATION •TO WATCH TV •ADJUSTING TWO PROGRAM WINDOWS •VARIOUS FUNCTIONS OF SIMULTANEOUS WINDOWS MODE •ADJUSTING VOLUME OF AN AUXILIARY WINDOW UTILITIES •OPEN FUNCTION MENU •ADJUSTING THE PICTURE •ADJUSTING THE SOUND •TIME SETUP •MEMORY FUNCTIONS •SPECIAL FUNCTIONS...
CONNECTING ANTENNA VHF/UHF OUTDOOR ANTENNAS NOTE: Bad picture reception could often be caused by bad antenna connection. Be sure to check the antenna direction, its height, etc. In case of using single antenna cable: VHF Antenna LTo Receive Cable Programs UHF Antenna Plug CATV coaxial cable in the antenna socket (unit) in the back...
Sensing light automatically. Remote Control. Timer Lamp This lamp is lighted when “On”or “Off” function is set up in the timer memory. DTQ-29U9FS Digital Sensor Sensing light automatically. Timer Lamp This lamp is lighted when “On”or “Off” function is set up in the timer memory.
Page 8
(sub stations) TV/CABLE Power (Selection Button) (Button) Volume TV/VIDEO (Adjustment Button) (Selection Button) DTQ-29U9FS Connection Sockets for MENU auxiliary units Channel This button is used in adjusting the (sub stations) (Selection Button) picture, sound, time setup, and controlling various other functions.
Remote Control • ( )Numbers in the blank serve as an address, which shows the page number containing detailed information on the functions of each button. TV Power RECALL The present modes of channel, video, transmission signal, and equalizer can be MUTE checked through this button.
Page 10
Note: Under the Cover of Remote Control •When batteries are weak Remote Control may not work. Change them immediately when they get weak. To use the buttons under the cover •Be sure to use two 1.5V size AAA batteries. PIP SEARCH 10~26 Simultaneous window selection is possible through the buttons of this...
To Watch TV Program To Watch TV Program: Buttons on the top of TV set have the same functions as those with the same names on the REMOTE CONTROL. BPress two number buttons of Remote Control to select a channel directly with its numbers.
Page 12
To Mute the sound instantly: LThis function is used when there is a 1.Press “TV POWER”button: phone call or a visitor. LPress “MUTE” button, to stop the •Then the TV screen will become bright and the sound of the program. Mono stand-by lamp will go off as well.
Page 13
Automatic Memory of Channel: LActual broadcast channels can be 1.Press “MENU” button. set up in the “Memory” of TV set through this function. •Then the screen appears as follows With setup of automatic channel memory, desired channels can be selected easily with“CHANNELx/y” Picture buttons.
Page 14
4.Press “VOLUMEC/B” buttons. Automatic Channel memory function (Auto Program) starts. •Checking from channel 2 to channel 69,(Cable1~125) Auto Program this function automatically memorizes only those Auto Programming channels which are actually broadcast. •When “MENU” button is pressed in the middle of - 13 - setup process, the setup operation quits.
Page 15
Additional Channel Memory Function :“ADD/ERASE” LWhen it is hard to put a channel in a 1.Select a channel you want to memorize. memory due to a weak broadcast signal, an additional memory of the •Select a channel by pressing number buttons. channel is possible through this Mono Ex) Ch 13...
Watching CATV programs: LWatching CATV programs is 1.Press “TV/CATV” button. possible only in areas where CATV service is provided. When pressed once •Then reception mode shifts from aerial TV to Cable Cable 12 Cable 12 When pressed twice 2.Select a channel. •Select a channel by pressing either number buttons 0 - 9 or 100.
Page 17
Watching Video Programs 1.Connect the video cable to the VIDEO socket in the back and side of TV set, and press “TV/VIDEO” button on the remote control. •The screen shifts in video mode as follows. Video1 •Whenever this button is pressed, the screen shifts in sequence : Channel Video1 Video2...
Adjusting Two Program Windows Operating Two Program Windows: LSound of TV set is available only in 1.Press “PIP” button once. the main program window (the left one). •Single PIP appears on the screen. Mono LIf you want to listen to the sound of an auxiliary window (the right one), use Headphone.
Various Functions of Simultaneous Windows Mode Various Functions of Simultaneous Window Mode: LSelect and enjoy programs you want to watch by using various functions 1.Press “MENU” button. of Simultaneous Windows •Then the screen appears as follows. Picture Move Sel. Exit 2.Select “Funtion”...
Page 20
5.Press “VOLUMEC/B” buttons, and select the window mode you want. •When the “VOLUMEC/B” buttons is pressed, the screen shifts in sequence as follows: Single PIP Picture Twin picture Multi-picture(4) Multipicture(7) Off, and vice versa. Single PIP Picture Twin Picture Mono Mono Multi-Picture(4) Multi-Picture(7)
Page 21
Selecting Simultaneous Windows: LYou can enjoy two window programs 1.Press “PIP” button. at the same time. Along with the main window program, you can have •You can enjoy the two window programs another TV channel program or a Mono simultaneously. Video program simultaneously.
Page 22
4.Press “PIP” button one more time. •PIP mode is changed twin window. Mono Mono 5.Press “PIP” button one more time, and then the auxiliary window disappears. •Whenever the “PIP” button is pressed, the screen Mono mode is changed cyclically as follows: Mono Mono...
Page 23
Searching Function of Memorized Channels through 7 Window and 4 Window modes. LMemorized channels could be 1.Press “SEARCH” button. checked easily by selecting 4 window modes or 7 window modes. •Four windows appear on the screen. Memorized channels are connected to each window one-by-one in sequence, so it is easy to check the contents of the programs on air .
Page 24
Searching Location Shift among Auxiliary Windows: 1.Press “POSITION” button. •Bring auxiliary windows on the screen by pressing “PIP” buttons. •Press “POSITION” button. Every time it is pressed, the locations of auxiliary windows change as follows: •The search sign “B” in 4 Window mode shifts its location as follows: Mono •The search sign “B”...
Page 25
Window Mode SWAP Press “SWAP” button. •Bring an auxiliary window by pressing “PIP” button. •Press “SWAP” button. Every time it is pressed, the modes of the main and auxiliary windows will shift their locations to each other as follows: Mono Mono This function also operates in Twin Window mode.
Page 26
Changing Window Modes is also Possible in Multi-Window Search. •The window with “B” sign converts to a new main window mode, and the channel of the new main window also appears as an auxiliary window channel of the new screen. Mono Mono Mono...
Adjusting Volume of an Auxiliary Window Headphone LSound of either the main window or 1. Press “MENU” button. an auxiliary window is available through headphone. •Then the screen appears as follows. LVolume control of an auxiliary window is possible only with Picture headphone.
Open Function Menu Accessing to “Sound” sub-menu: LEnjoy programs with selected modes 1. Press “MENU” button by using various functions. •When this button is pressed, the screen appears as follows. Picture Move Sel. Exit 2. Select “Sound” menu by using “VOLUMEC C /B B ” buttons. •Move the cursor to the “Sound”...
Adjusting the Picture Adjusting Picture Quality LUsers do not need to handle many 1. Press “AUTO PICTURE” button operation units in adjusting the picture on the screen. Just make one •The following pictures appear on the screen in sequence and the picture adjustment of the selections already built in by state is changed.
Picture Noise Reduction LWeak transmission signals could 1. Press “MENU” button. cause bad picture or noise. LThis function corrects this type of •Then the screen appears as follows : problem. Picture Move Sel. Exit 2. Select “Picture” by using “CHANNELx x ” button. •Move the cursor to the “Picture”...
Page 31
Adjusting the Picture Screen to Your Preference: LAccording to the user’s preference, 1.Press “MENU” button. brightness, contrast, sharpness, color and tint can be adjusted for •Then the screen appears as follows: each of Video mode 1, Video mode 2, Video mode 3, Game mode, and TV mode.
Page 32
3. Adjust “Tint” by using “VOLUMEC C /B B ” buttons. •Press “VOLUMEC” button, and the tint of green Picture Brightness gets strong. Contrast Press “VOLUMEB” button, and the tint of red gets Sharpness Color strong. Tint 50:50 Picture NR Move Adj.
Adjusting the sound Tuning as Prefered: LThrough this function, “Pitch” and 1. Press “MENU” button. “Tone”can freely be adjusted according to the user’s preference. •Then the screen appears as follows : Picture “Balance” LThis function controls the volume Move Sel. Exit balance between left and right speakers.
Page 34
4. Select Range of Sound by using “VOLUMEC C /B B ” buttons. •“CHANNELx” strengthens the selected range of Equalizer sound, and “CHANNELy” does the opposite (weakens the range of sound) •Signal bar (-) moves up and down showing the Move Adj.
Page 35
Receiving Stereo or SAP Mode Programs: LWhen transmission signal is weak or 1.Press “MTS” button: broadcasting condition is not good sound might be cut off temporarily. •Whenever this button is pressed the status of mode shifts in the following sequence: This type of malfunction is not Mono Stereo...
Time Setup Setting up Present Time: LBefore setting up Automatic “On” / 1. Press “MENU” button. “Off” mode or “Sleep” mode in the memory, the present time must be •Then the screen appears as follows : set up ahead. Picture Move Sel.
Page 37
4. Set up the Present Time. •Press “VOLUMEC/B” buttons, and the screen Timer Clock AM 1:00 appears as shown in the left figure: On Time •Press “CHANNELx/y” buttons, and the letters - - : - - Off Time “AM 1:00” turn blue. - - : - - •Set up the present time by using “VOLUMEC/B”...
Memory Functions Time Memory Setup for Automatic “On” and “Off”: LThis time memory function autom- 1. Press the “MENU” button. atically turns the TV set “On” or “Off” at a planned time. Once set up, this •Then the screen will appear as follows : function works every day unless the set time is canceled or the TV set is unplugged.
Page 39
4. Select the “On Time” to turn the TV set “On” •Press “CHANNELx/y” buttons, and the screen Timer appears as follows: Clock AM 1:00 On Time - - : - - Off Time - - : - - Move Sel. Prev.
Page 40
7. Set up the “Off Timer”. •Press “CHANNELx/y” buttons and the letters “AM Timer Timer Clock AM 1:00 - - : - -” turn blue. On Time •Set up “Off Timer” by using “VOLUMEC/B” buttons AM 11:00 Off Time •Keep pressing the “VOLUMEC/B” buttons then the PM 11:30 set up time continues to change by the unit of one Move...
Special Functions Shifting the On-Screen Language: LThe language of the program on the 1.Press “MENU” button. screen can be shifted to one of the following On-Screen languages : •Then the screen appears as follows : English, Spanish, Portuguese, and Franch according to the user’s selection.
Page 42
4.Select the language you want by using “VOLUMEC C /B B ” buttons. •Press this button, and the On-Screen language sign shifts in the following order : Fran •Select the language you want. Set Up Instalar Air/Cable Aire/Cable Aire Auto Program Autoprogramar Ch Edit Program manual...
Page 43
Setting up “Channel Edit”: LIn addition to the numerical channel 1.Press “MENU” button. Edit, users can add 4 letters to it. •Then the screen appears as follows : Picture Move Sel. Exit 2.Select “Set Up” by using “VOLUMEC C /B B ” buttons. •Move the cursor to the “Set Up”...
Page 44
4.Select “Ch labels” set up mode by using “VOLUMEC C /B B ” buttons. •Press “VOLUMEC/B” buttons. Then the following Ch Edit picture will appear on the screen. Channel Add/Erase •Select “Add/Erase” to turn “Add”. CH Label •Select “CH Label” to turn “On”. Move Adj.
Page 45
Setting up “Captions” function: LCaptions are hidden words that can 1.Press “MENU” button. be displayed on your TV screen. There are two types of these word: •The screen will then appear as follows : “Caption” usually follows the action on-screen, providing a written version of the dialogue, narration, Picture and sound effects: “text”...
Page 46
4.Select the entry you want by using “VOLUMEC C /B B ” buttons. •Press “VOLUME B” button and the entry changes Function Timer in the following order: Child Lock Auto demo Caption •Select the type of caption or text you want. Move Sel.
Page 47
Setting up “Child Lock” function: LUsers can lock channels by 1.Press “MENU” button. registering them with 4-digit codes. LWhen “Child Lock” is set up, the •The screen will appear as follows : channels locked are not available on the screen. Picture Move Sel.
Page 48
4.Select “Child Lock” function by using “VOLUMEC C /B B ” buttons. •The screen will appear as follows: Child Lock LOCK1 LOCK2 LOCK3 LOCK AV Password ---- LOCK set Move Sel. Prev. Child Lock •Install 4-digit Password by pressing the number LOCK1 buttons on the Remote Control.
Page 49
•When all the selections are completed, move to “Lock Set” function to set up the “Child Lock” function. And select “On” there. Child Lock LOCK1 LOCK2 LOCK3 LOCK AV Password 1234 LOCK set Adj. Move Prev. •The channels and video mode which are locked do not operate on the screen. •In order to change channels locked, move to such “Menu”...
Page 50
Setting up “Auto Demo” function: LThis function brings various on- 1. Press “MENU” button. screen menus automatically in sequence. •The screen will appear as follows : Picture Move Sel. Exit 2. Select “Function” by using “VOLUMEC C /B B ” buttons. •Move the cursor to the “Function”...
Page 51
Surround function LYou can hear live Surround 1. Press “SURROUND” button with Remote Control. according to broadcastion program. • Select “Special” of “OSD” with using “MENU”, “VOLUMEC/B” and CHANNELx. Special Move Sel. Exit Special Special • Setup “Surround” to turn “On”. Surround Digital Sensor Move...
Page 52
“Digital Sensor” Function LYou can adjust the state of screen 1. Press “MENU” button according to light and surrounds automatically. •Then the screen appears as follows. Picture Move Sel. Exit 2. Press “Special” by using “VOLUMEC C /B B ” buttons •Move the cursor to the “Special”...
Connecting VCR or Other AV sets Names of Connection Units and Their Functions BWhen the TV set is in Video Mode, Monitor transmits Video signal out.
Page 54
Interface with Video Connection Unit on the back of TV set, and that of VCR set Prepare Picture/Sound connection codes (accessories for separate sale). Connect “Picture Out” unit of VCR set with “Picture In” of TV set. Connect “Sound Out” unit of VCR set with “Sound In”...
Page 55
Connection with S-Picture Video set Connection Unit on the back of TV set When you want to watch a clear picture image of S-Picture program on TV screen, connect High Fidelity VCR program to S-picture Connection Unit of TV set, and you can enjoy clean and clear Connect the “S-VHS Out”...
Page 56
Connecting Camcorder (Video Camera) to TV set Connecting Camcorder to TV set When you want to watch the images captured by Video Camera, Prepare Picture and Sound connect the camcorder to the connection unit on the side of TV set. connection cables.
Page 57
Connecting the TV set to an Audio set When you want to have the picture of a program on TV screen and the sound of it from the To operate: Audio set, 1. Set the volume of TV set at Connect the external “Input Terminal”...
Troubleshooting B B Before Asking for Service: Neither picture nor sound: Picture is OK, but no Sound is OK, but no Overlapped Picture sound: color: Image: •Check if the set is plugged in. •Check if Volume Down is •Check if the color control is •Check if the antenna direction pressed.
Specifications BRAND DAEWOO MODELS DTQ-29U9FS/29X9FS MAIN VOLTAGE 110/220V~ 50/60Hz POWER CONSUMTION 140 W SYSTEM NTSC-M VHF: 2-13 CHANNELS: 181 UHF: 14-69 CATV 1~125 IMPEDANCE VHF/UHF 75 Ohm WEIGHT 29U9FS : 56 kg 29X9FS : 52,5 kg DIMENSION 29U9FS : 843 x 592 x 504mm...