Advertisement
Now start...
With pump in room where
it
will be installed.
1
.
Determine
where you wish to
locate
water pump and water
bottle.
The water bottle and water
pump should be installed
on the same
level.
The water bottle and water pump must
be located
close together
since the
tubing
connecting
the pump to the
water bottle is 1.8m (6 feet) long.
Use
existing
tubing
between
water pump
and water bottle. Do Not cut this tubing
or add tubing
between
pump and water
bottle. Do Not remove
clamp
on end of
tubing
that connects
inner tubing
to
outer tubing.
Suggested
locations:
l
Under the sink .
l
Cabinet
next to refrigerator.
2
Determine
where you will need
. to run water lines and the
length
of tubing
that will be
needed.
If more tubing
is needed
than
what is supplied,
tubing
(Part No.
4319151) and tubing
connectors
(Part
No. 4319153) can be obtained
from
your dealer
or authorized
parts
distributor.
3
Attach
bottle cap to water
' bottle.
Push the tubing
into the
water bottle
until the end of the tubing
reaches
the bottom
of the bottle.
Do
Not remove
clamp
from end of tubing.
4
,
Insert one end of the outlet
tubing
into connector
located
on outside of pump as far as it will go, If
tubing
needs to be adjusted,
push
connector
in and pull tubing
out.
5
Route the tubing
to the
refrigerator.
Cut tubing
to
'
length
needed.
6
Plug power supply cord into
'
earthed,
electrical
outlet.
Press
the pump switch to the "I" position.
connector
tubing
collet
7
,
Run enough
water through
refrigerator
to fill a glass or other
container.
Check all connections
for
leaks.
If a connection
leaks, push in collet and
remove
tubing.
Cut off 1.3cm (l/2")
of
tubing
and reinsert into connector.
If unit is connected
ONLY to a
refrigerator
icemaker,
the icemaker
will
have to call for water before pump can
be checked
for leaks.
Information
The water pump operates
automatically
when dispenser
is
operated.
When the dispenser
is
released,
the water pump
automatically
stops operating.
When water bottle empties
during
use:
Pressurized air is expelled
through
dispenser
when water bottle
is
empty.
1
Stop dispensing
from the
'
refrigerator.
2
n
3.
bottle
bottle
Press the switch on the
water pump to the "0"
position.
Remove
bottle cap from water
bottle.
Replace
empty
water
Attach
bottle
cap to full water
Press the switch
on the water
pump to the "I" position.
If water bottle empties
while
unattended,
the pump will run for
2-l /2 minutes and then automatically
shut off.
1.
2.
bottle.
bottle.
3.
Press the switch on the water
pump to the "0" position.
?emove
bottle cap from water
mottle. Replace
empty water
Attach
bottle cap to full water
Press the switch on the water
pump to the "I" position.
If water system is exposed
to
temperatures
below
0°C (32'F),
the system must be drained.
Remove
tube from bottle.
Open all
outlets and run pump to inject air
through
all outlets.
Cleaning
and sanitizing
system:
System should be cleaned
after
extended
periods of non-use.
1
n
2.
3.
4,
Add one-half
teaspoon
of
chlorine
bleach
to one gallon
of
water.
Inset-t tube into solution
and start
w-w
Open all outlets to fill system with
solution.
Let stand five minutes.
Flush system with water until
chlorine
is removed.
Panel B
Advertisement
