Advertisement
Quick Links
PRODUCT PROFILE
PACKAGED TERMINAL AIR CONDITIONERS AND HEAT PUMPS
WallMaster
7,000 / 9,000 / 12,000 / 15,000 Btu/h
Standard Features
!
Ultrahigh efficiency. Up to 12.2 EER.
!
Unique component mounting and isolation
provide ultraquiet operation and vibration
dampening.
!
Large well spaced control panel with
universal markings and non-removable
controls
!
Attractive front cover and tamper resistant
contoured discharge grille blend with any
decor.
!
Quiet and efficient rotary compressor
mounted on vibration isolators, with internal
high temperature overload protection.
!
Built-in damper allows up to 70 CFM of
fresh air.
!
Convenient top-mounted return air filters.
AMERICA'S BEST AIR CONDITIONER
®
The All-new Friedrich
WallMaster
for:
New construction in hotels/
motels, medical facilities, assisted
living centers, apartments/condos,
office suites, dormitories and
remodels.
The New WallMaster
into existing 16" x 42" sleeves
more easily than other
manufacturer's PTACs.
!
Available in heat pump or electric heat.
!
Front cover fastens to chassis with
thumbscrews hidden from user.
!
Emergency heat compressor override
switch on all heat pumps.
!
Single, totally enclosed "clam shell" motor
design protects against premature failure.
!
Optional seacoast protection for harsh
coastal environments.
!
Complete line of accessories.
!
Remote thermostat control units are
available.
!
Units are rated in accordance with ARI
Standard 310/380.
!
Manufactured in the U.S.A.
is a perfect fit
®
retrofits
®
Advertisement
Related Manuals for Friedrich WallMaster PACKAGED TERMINAL AIR CONDITIONERS AND HEAT PUMPS
Summary of Contents for Friedrich WallMaster PACKAGED TERMINAL AIR CONDITIONERS AND HEAT PUMPS
-
Page 1: Standard Features
Built-in damper allows up to 70 CFM of fresh air. Convenient top-mounted return air filters. AMERICA'S BEST AIR CONDITIONER The All-new Friedrich WallMaster for: New construction in hotels/ motels, medical facilities, assisted living centers, apartments/condos, office suites, dormitories and remodels. - Page 2 PE Series Chassis Specifications M O D E L S : PE07K P E R F O R M A N C E D A T A : Cooling Btuh. 7500/7300 Cooling Power (W) 615/598 12.2 Dehumidification (Pts/h) Sensible Heat Ratio 0.76 E L E C T R I C A L D A T A :...
- Page 3 Extended Cooling Performance, PE07/09/12/15 Btuh 8820 8483 Watts PE07 Amps 0.52 0.71 10819 10405 Btuh Watts PE09 Amps 0.51 0.70 Btuh 14112 13572 12564 13440 12672 11688 12912 12000 10620 12096 10740 9468 Watts PE12 Amps 0.49 0.67 17640 16965 15705 16800 15840 14610 16140 15000 13275 15120 13425 11835 13455 11580 10230 Btuh 1288 1309...
-
Page 4: Nominal Cooling Capacity
Electric Heat Data, PE/PH 07/09K/R M O D E L S : PE/PH07K P E R F O R M A N C E D A T A : Heater Watts 2500/2050 Voltage Heating Btuh 8500/7000 Heating Power (Watts) 2600/2150 Heating Current (Amps) 11.4/10.4 Minimum Circuit Ampacity... - Page 5 Typical Wall Sleeve Installation (PXWS) Lintel Used To Support Masonry Walls Electrical Receptacle Main Studs Jack Stud Extended Wall Sleeve Installation and Sealant Locations (PXWE) Wall Sleeve Extension, 42" X 16" Frame, 20 gauge minimum, painted or aluminum Width of Wall Electrical Receptacle 16¼"...
- Page 6 Internal Drain Kit Location and Installation (PXDR10) Wall Sleeve Bottom Gasket Foam Mounting Plate Tube Screw Screw 1/2" O.D. Tube Mounting Plate Gasket External Drain When using an external drain system, the condensate is removed through either of two drain holes on the back of the wall sleeve. Select the drain hole which best meets your drainage situation and install the drain kit.
- Page 7 All units shall be factory run-tested to check operation and be Friedrich WallMaster® or equivalent. The basic unit shall not exceed 16" high x 42" wide. Overall depth of the unit from the rear of the Friedrich wall sleeve to the front of the decorative front cover shall not exceed 21¼".
- Page 8 Friedrich PTAC Accessories New Construction Accessories MODEL NUMBER WALL SLEEVE G-90 zinc coated steel is prepared in an eleven-step process, then powder coated for maximum coverage and protection. The wall sleeve is insulated for thermal efficiency. 16" High PXWS x 42" Wide x 13¾" Deep.
- Page 9 2¼" sleeve extension attached to the PXSE room side of the sleeve to allow for the installation of a P-Series Friedrich PTAC in a T-Series sleeve. LATERAL DUCT ADAPTER Attaches to the PTAC/ PTHP unit and provides a transition to direct up to...
- Page 10 For international warranty information, contact the Friedrich Air Conditioning Company - International Division. Reasonable proof must be presented to establish the original purchase date, otherwise the beginning date of this certificate will be considered to be our shipment date plus sixty days.
- Page 11 Made in the U.S.A. " UL Listed and ARI Certified " Wall Sleeve Width Height 42" 16" Wall Opening - 42¼" wide x 16¼" high Date: For Reference: VOLTAGE FRIEDRICH MODEL FEATURES DIMENSIONS Overall Depth Depth Sleeve with Front 13¾" 21¼"...
-
Page 12: Multiple Solutions
Multiple solutions. One trusted name. Friedrich Air Conditioning Co. Post Office Box 1540 · San Antonio, Texas 78295-1540 4200 N. Pan Am Expressway · San Antonio, Texas 78218-5212 (210) 357-4400 · FAX (210) 357-4480 www.friedrich.com Printed in the U.S.A PTACBW02 (04/02)