Related Manuals for Planet ISW-802M
Summary of Contents for Planet ISW-802M
- Page 1 6-Port 10/100Mbps TP + 2-Port 100Base-FX Managed Industrial Ethernet Switch ISW-802M User's Manual...
-
Page 2: Fcc Warning
Copyright PLANET Technology Corp. 2006. Contents subject to which revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose. -
Page 3: Table Of Contents
Table of Contents 1. INTRODUCTION ........................5 1.1 Packet Contents ......................5 1.2 How to Use This Manual ....................5 1.3 Product Feature....................... 5 1.4 Product Specification....................... 6 2. HARDWARE INSTALLATION ....................9 2.1 Product Description ......................9 2.2 Mounting Installation ..................... 14 3. - Page 4 4.12 IP Configuration......................36 4.13 SNTP Configuration ....................37 4.14 IP Security ........................39 4.15 RSTP Configuration ....................40 4.16 Redundant Ring ......................42 4.17 QoS Configuration....................... 44 4.18 IGMP ........................... 46 4.19 SNMP Configuration....................47 4.20 Security Manager ......................49 4.21 Configuration Backup....................
-
Page 5: Introduction
1. INTRODUCTION The 6-Port 10/100TX plus 2-Port 100FX with redundant ring managed industrial switch is a cost-effective solution and meets the high reliability requirements demanded by industrial applications. The switch can be easily managed through the Web GUI. By using fiber port can extend the connection distance that increases the network elasticity and performance. -
Page 6: Product Specification
System event log support ▫ Configuration backup/restore ▫ E-mail event alert ▫ IP security for illegal access prevention ▫ TFTP firmware upgrade ▫ Port mirror transmission monitoring 1.4 Product Specification Model ISW-802M Hardware Standard IEEE 802.3af, IEEE 802.3, IEEE802.3u, 10/100Base-TX 10/100Mbps TP... - Page 7 100Base-FX 2 (mm, sc) Protocol CSMA/CD Switching Architecture Store and forward Transfer Rate 144,880 pps for Ethernet port and 1448,800 pps for Fast Ethernet port MAC address Memory Buffer 1Mbit Network Cable 10Base-T : 2-pair UTP/STP Cat 3, 4, 5 cable 100Base-TX: 2-pair UTP/STP Cat.
- Page 8 service. IGMP Support IGMP v1 and Query mode. Up to 256 groups. Spanning tree IEEE802.1d spanning tree and IEEE802.1w rapid spanning tree. SNTP Support simple network time protocol. SMTP Support simple mail transfer protocol. Bandwidth control Support ingress packet filter and egress packet limit. The egress rate control supports all of packet type and the limit rates are 128kbps, 256Kbps, 512Kbps, 1MB, 2MB, 4MB, and 8MB.
-
Page 9: Hardware Installation
2. HARDWARE INSTALLATION This section describes the functionalities of the Switch's components and guides how to install it on the rack or mount to the wall. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.1 Product Description The PLANET Managed Industrial Ethernet Switch provides substation hardened, fully managed, Ethernet switches specifically designed to operate reliably in electrically and environmentally harsh environments. -
Page 10: Led Indications
Figure 2-1 ISW-802M Front Panel 2.1.3 LED Indications Status Meaning Green The switch unit is power on. Power The switch unit is no power input. Green Power on Power 1 No power inputs Green Power on Power 2 No power inputs... -
Page 11: Reset Button
No device attached Yellow The port is operating in full-duplex mode. FDX/COL Blinks Collision of Packets occurs in the port. (Port 7 & 8) The port in half-duplex mode or no device attached 2.1.4 Reset Button The reset button provides user a quick and easy way to restart and set the configuration back to default value. -
Page 12: Wiring The Power Inputs
2. Please restart the switch after the Redundant ring DIPswitch is set. 2.1.6 Switch Bottom Panel The bottom panel of the ISW-802M consists one terminal block connector within two DC power inputs and one DC IN power jack for extra AC/DC power adapter. -
Page 13: Wiring The Fault Alarm Contact
1. Insert the positive and negative wires into the V+ and V- connector on the terminal block connector. 2. To tighten the wire-clamp screws for preventing the DC wires to loose. Power Notice: The wire range of terminal block is from 12~ 24 AWG. 2.1.8 Wiring the Fault Alarm Contact The fault alarm contact is in the middle of terminal block connector as below figure shows. -
Page 14: Mounting Installation
Fault Alarm Contact The open circuit will form when the power failure or port link failure. 24V DC Buzzer 24V Battery The fault alarm device will send a warning signal t warn the user, ex: alarm sound or flash light. 2.2 Mounting Installation This section describes how to install the Ethernet Switch and make connections to it. -
Page 15: Wall Mount Plate Mounting
Step2: Lightly push the button of DIN-Rail into the track. Step3: Check the DIN-Rail is tightly on the track. Step4: To remove the industrial switch from the track, reverse steps above. 2.2.2 Wall Mount Plate Mounting To install the switch on the wall, please follows the instructions described below. Step1: Remove the DIN-Rail from the industrial switch;... - Page 16 Step3: Use the screws to screw the wall mount plate on the industrial switch. Step4: Use the hook holes at the corners of the wall mount plate to hang the industrial switch on the wall. Step5: To remove the wall mount plate, reverse steps above.
-
Page 17: Network Installation
3. NETWORK INSTALLATION 3.1 Hardware Installation In this paragraph, we will describe how to install the redundant ring Web management industrial switch and the installation points for attention. Unpacked the Industrial switch. Check the DIN-Rail is screwed on the Industrial switch. If the DIN-Rail is not screwed on the Industrial switch. -
Page 18: Redundant Ring Application
3.3 Redundant Ring Application The industrial switch supports the redundant ring protocol that can help your network system to recovery from network connection failure within 300ms or less, and make your network system more reliable. The redundant ring algorithm is like as spanning tree protocol (STP) algorithm but it has faster recovery time than STP. -
Page 19: Coulping Ring Application
3.4 Coulping Ring Application In the network, it may have more than one redundant ring group. By using the coupling ring function can connect each redundant ring for the redundant backup. It can ensure the transmissions between two ring groups will no failure. The following figure is a sample of coupling ring application. -
Page 20: Dual Homing Application
3.5 Dual Homing Application Dual Homing function is to prevent the connection lose between redundant ring group and upper level/core switch. Assign two ports to be the Dual Homing ports that one is working port and one is backup port in the redundant ring group. The backup port that has smaller MAC address value will be selected by switch automatically. -
Page 21: Web Management
4. WEB MANAGEMENT This section introduces the configuration and functions of the Web-Based management. The following configuration steps are based on the firmware version 1.00. 4.1 About Web-based Management Inside the CPU board of the switch exists an embedded HTML web site residing in flash memory. It offers advanced management features and allow users to manage the switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer. -
Page 22: Port Status
The Web management interface 4.4 Port Status In Port status, you can view every port status that depended on user's setting and the negotiation result. Port: the port number. Type: the speed mode, ex: 100TX = 100Mbps. Link: "Down" is "No Link". "UP" is "Link". State: display port statuses "disable"... -
Page 23: Single Port Information
Port Status interface 4.5 Single port information You can click the port on the Panel figure on the left side of web GUI. Then, the single port information window will pop up and display the port current status information. Port information interface... -
Page 24: Port Statistics
4.6 Port Statistics The following information provides a view of the current port statistic information. Click button to clean all counts. Port Statistics Interface 4.7 Port Control You can change the port status. Select the port by scroll the Port column. State: disable or enable control of his port. -
Page 25: Switch Settings
Port Control interface 4.8 Switch Settings You can assign the system name and location and view the system information. System Name: assign the name of switch. The maximum length is 64 bytes. System Location: assign the switch physical location. The maximum length is 64 bytes. System Description: display the description of switch. -
Page 26: Port Mirroring
Switch Settings interface Remember to execute the "Save Configuration" action, otherwise the new configuration will lose [NOTE] when the switch power off. 4.9 Port Mirroring The Port mirroring is a method for monitor traffic in switched networks. Traffic through ports can be monitored by one specific port. -
Page 27: Vlan Configuration
Port Mirroring intrerface 4.10 VLAN configuration A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic so only members of the VLAN receive traffic from the same VLAN members. Basically, creating a VLAN from a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch. - Page 28 VLAN Configuration interface 4.10.1 Port-based VLAN Packets can go among only members of the same VLAN group. Note all unselected ports are treated as belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging is ignored. In order for an end station to send packets to different VLANs, it itself has to be either capable of tagging packets it sends with VLAN tags or attached to a VLAN-aware bridge that is capable of classifying and tagging the packet with different VLAN ID based on not only default PVID but also other information about the packet, such as the protocol.
- Page 29 VLAN – Port-based interface Click to add a new VLAN group. The maximum VLAN group is up to 64 VLAN groups. Group Name: assign the VLAN group name, ex: VLAN001. VLAN ID: assign the VLAN ID (between 1 and 4094). Select the members of VLAN group.
- Page 30 VLAN – Port-based Add interface You will see the VLAN group displays. If the groups' list is more than one page, you can click to view other VLAN groups. button to delete unwanted VLAN. button to modify existing VLAN group. Remember to execute the "Save Configuration"...
- Page 31 802.1Q VLAN interface 4.10.2.1 Basic Click button. Management VLAN ID: it is used for remote management security. Only the port of VLAN group ID is equal to the Management VLAN ID can remote management that include telnet, SNMP, and Web browse the switch. Fill the specific VLAN ID number in Management VLAN ID column and mark the check box, and then click button to enable the function.
- Page 32 802.1Q VLAN – Add interface Click . Then you will see the page as follow.
-
Page 33: Alert
To set the outgoing frames are VLAN-Tagged frames or untagged. Then click Tag: outgoing frames with VLAN-Tagged. Untag: outgoing frames without VLAN-Tagged. : Configure port VID settings 4.10.2.2 Port VID Port VLAN ID: enter the port VLAN ID. Click To reset back to default value, click button. -
Page 34: Event Configuration
user. You can set up the mail server IP, mail account, and forwarded email account for receiving the event alert. Email Alert: enable or disable the email alert function. SMTP Server IP Address: set up the mail server IP address. Authentication: mark the check box to enable and configure the email account and password for authentication. -
Page 35: Power Alarm Configuration
Device cold start: when the device executes cold start action, the system will send out the alert to the dedicate SMTP server. Power status: when the device power status has changed, the system will send out the alert to the dedicate SMTP server. SMNP Authentication Failure: when the SNMP authentication fail, the system will send out the alert to the dedicate SMTP server. -
Page 36: Ip Configuration
Power Alarm interface 4.12 IP Configuration Power alarm function enables the Relay alarm action. Without enabling power alarm function, the Relay alarm action will not work even the Relay alarm is set. Mark the check box and click button. DHCP Client: Enable or Disable the DHCP client function. When DHCP client function is enabling, the industrial switch will be assigned the IP address from the network DHCP server. -
Page 37: Sntp Configuration
IP Configuration interface 4.13 SNTP Configuration You can configure the SNTP (Simple Network Time Protocol) settings. The SNTP allows you to synchronize switch clocks in the Internet. SNTP Client: enable or disable SNTP function to get the time from the SNTP server. UTC Timezone: set the switch location time zone. - Page 38 ADT - Alaskan Daylight ALA - Alaskan Standard -9 hours 3 am HAW - Hawaiian Standard -10 hours 2 am Nome, Alaska -11 hours 1 am CET - Central European FWT - French Winter MET - Middle European +1 hour 1 pm MEWT - Middle European Winter SWT - Swedish Winter...
-
Page 39: Ip Security
SNTP Configuration 4.14 IP Security IP security function allows you to assign 10 specific IP addresses that have permission to access the switch through the web browser for the securing switch management. Enable the IP Security: mark the check box to enable the IP security function. Security IP 1 ~ 10: you can assign up to 4 specific IP address. -
Page 40: Rstp Configuration
IP Security interface 4.15 RSTP Configuration The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and provides for faster spanning tree convergence after a topology change. The system also supports STP and the system will auto detect the connected device that is running STP or RSTP protocol. 4.15.1 System Configuration You can view spanning tree information about the Root Bridge. -
Page 41: Per Port Configuration
Forward Delay Time (4-30): the number of seconds a port waits before changing from its Rapid Spanning-Tree Protocol learning and listening states to the forwarding state. Enter a value between 4 through 30. [NOTE] Must follow the rule to configure the MAX Age, Hello Time, and Forward Delay Time. 2 x (Forward Delay Time value -1) >... -
Page 42: Redundant Ring
To configure the port as an edge port, set the port to "True" status. Admin Non Stp: The port includes the STP mathematic calculation. True is not including STP mathematic calculation. False is including the STP mathematic calculation. Click button. Remember to execute the "Save Configuration"... - Page 43 address number as the ring master. The redundant ring master ring mode will be enabling by the DIP Switch. When the switch is set to the master ring mode, the redundant ring configuration interface will display the switch as the master ring message. Also, you can identify the switch as the ring master from the R.M.
-
Page 44: Qos Configuration
Redundant Ring interface [NOTE] When you enable the redundant ring function, you must disable the RSTP. The redundant ring function and RSTP function cannot exist at the same time. Remember to execute the "Save Configuration" action, otherwise the new configuration will lose when the switch power off. - Page 45 TOS first: the port priority will follow the TOS priority first, and the other priority rule. COS priority: set the COS priority level 0~7. TOS priority: the system provides 0~63 TOS priority level. Each level has 4 type of priority - high, mid, low, and lowest.
-
Page 46: Igmp
QoS Configuration interface 4.18 IGMP The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP allows the ports to detect IGMP queries and report packets and manage IP multicast traffic through the switch. -
Page 47: Snmp Configuration
Message Description A message sent from the querier (IGMP router or switch) asking for a response Query from each host belonging to the multicast group. A message sent by a host to the querier to indicate that the host wants to be or Report is a member of a given group indicated in the report message. -
Page 48: Community String
4.19.1 System Operations Name: enter a name for the switch. Location: enter the switch physical location. Contact: enter the name of contact person or organization. 4.19.2 Community String Community strings serve as password for MIB read or write. Strings: fill the name of string. RO: Read only. -
Page 49: Security Manager
SNMP Management interface 4.20 Security Manager You can change web management login user name and password for the management security issue. User name: type the new user name. The default is "root". Password: type the new password. The default is "root". Confirm password: retype the new password. -
Page 50: Configuration Backup
Security Manager interface. 4.21 Configuration Backup In Configuration Backup, you can restore the backup configuration into the industrial switch. Also, you can backup the configuration to TFTP server. 4.21.1 TFTP Restore Configuration You can restore flash ROM value from TFTP server, but you must put the backup image in TFTP server, industrial switch will download the image back to the flash. -
Page 51: Tftp Backup Configuration
TFTP Restore Configuration interrface 4.21.2 TFTP Backup Configuration You can save current flash ROM value from the industrial switch to the TFTP server, then go to the TFTP restore configuration page to restore the image value back to the industrial switch. TFTP Server IP Address: fill in the TFTP server IP Backup File Name: fill the file name Click... -
Page 52: Factory Default
TFTP Backup Configuration interface 4.21.3 TFTP Update Firmware It provides the functions to allow a user to update the switch firmware. Before updating, make sure you have your TFTP server ready and the firmware image is on the TFTP server. TFTP Server IP Address: fill in your TFTP server IP. -
Page 53: Save Configuration
Factory Default interface 4.23 Save Configuration Save the industrial switch configuration to the flash memory. Power off the industrial switch without the saving, all changed configuration will lost. Click the button the save the configuration. Save Configuration interface... -
Page 54: System Reboot
4.24 System Reboot Reboot the Switch in software reset. Click button to reboot the switch. System Reboot interface 4.25 Rate Control You can set up every port's bandwidth rate and packet limitation type. Limit Packet type: select the packet type that want to filter. The packet types have all type packet, broadcast/multicast/unknown unicast packet, broadcast/multicast packet, and broadcast packet only. -
Page 55: System Log
when the switch power off. Qos and Rate control cannot be existed at the same. Rate Control interface 4.26 System Log You can set up system log events and view the system log events. 4.26.1 System Log Configuration You can view the system log events in here. Click button to get newest system log event and button to clear the log events. - Page 56 System Log Configuration 4.26.2 Event Configuration You can select the system log events. When selected events occur, the system will send out the log information. Also, per port log events can be selected. System event selection: 4 selections - Device cold start, Power status, SNMP Authentication Failure, and Redundant ring topology change.
- Page 57 down. After selected, click Event Configuration interface...
-
Page 58: Troubleshooting
5. TROUBLESHOOTING This section is intended to help you solve the most common problems on the industrial Ethernet switch. 5.1 Incorrect connections The switch port can auto detect straight or crossover cable when you link switch with other Ethernet device. For the RJ-45 connector should use correct UTP or STP cable, 10/100Mbps port use 2-pairs twisted cable. - Page 59 IF the power indicator does turn on when the power cord is plugged in, you may have a problem with power outlet, or power cord. However, if the Switch powers off after running for a while check for loose power connections, power losses or surges at power outlet. IF you still cannot resolve the problem, contact your local dealer for assistance.
-
Page 60: Appendix
6. APPENDIX 6.1 100BASE-TX/10BASE-T Pin Assignments With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data. RJ-45 Pin Assignments Pin Number Assignment "+" and "-" signs represent the polarity of the wires that make up each wire pair. Note: All ports on this switch support automatic MDI/MDI-X operation, you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs.