Dimplex BF33ST Parts & Service Manual
  1. Manuals
  2. Brands
  3. Dimplex Manuals
  4. Indoor Fireplace
  5. BF33ST
  6. Parts & service manual

Dimplex BF33ST Parts & Service Manual

Built in fireplace
Hide thumbs Also See for BF33ST:

Advertisement

Table of Contents

See also: Troubleshooting Manual , Installation Manual
PARTS & SERVICE MANUAL
FOR THE BUILT IN FIREPLACE
MODEL NUMBERS:
BF33ST/DX
BF39ST/DX
BF45ST/DX

Advertisement

Table of Contents
loading

Related Manuals for Dimplex BF33ST

Summary of Contents for Dimplex BF33ST

  • Page 1 PARTS & SERVICE MANUAL FOR THE BUILT IN FIREPLACE MODEL NUMBERS: BF33ST/DX BF39ST/DX BF45ST/DX...

  • Page 2: Table Of Contents

    HEATER ON/OFF SWITCH REPLACEMENT PAGE 12 FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 13 VOLTAGE SELECTOR SWITCH REPLACEMENT (UNIT IS PERMENANTLY INSTALLED IN WALL) BF33ST, BF33DX PAGE 15 BF39ST, BF39DX, BF45ST, BF45DX PAGE 17 VOLTAGE SELECTOR SWITCH REPLACEMENT PAGE 19 (UNIT CAN BE REMOVED FROM WALL)
  • Page 3 BLOWER MOTOR/BLOWER REPLACEMENT PAGE 25 (UNIT CAN BE REMOVED FROM WALL) TEMPERATURE LIMIT SWITCH REPLACEMENT (UNIT IS PERMENANTLY INSTALLED IN WALL) BF33ST, BF33DX PAGE 26 BF39ST, BF39DX, BF45ST, BF45DX PAGE 28 TEMPERATURE LIMIT SWITCH REPLACEMENT PAGE 30 (UNIT CAN BE REMOVED FROM WALL)

  • Page 4: Operation

    BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX OPERATION MANUAL CONTROLS (WITHOUT REMOTE OPTION) The fireplace can be controlled by the manual switches located on the fireplace (FIGURE 1). Main Power Switch Main ON/OFF switch, activates the flame effect. Heater Control Switch Heater ON/OFF switch, activates heater to the high level.

  • Page 5: Remote Control

    BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX REMOTE CONTROL The remote control has a range of approximately 50ft. (15.25m). It does not have to be pointed at the fireplace and can pass through most obstacles (including walls). It is supplied with one of 243 independent frequencies to prevent interference with other units.

  • Page 6: Voltage Selector Switch Location

    BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX RESETTING THE TEMPERTURE CUTOUT SWITCH The heater on this fireplace is protected with a safety device to prevent overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset.
  • Page 7 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX...

  • Page 8: Replacement Parts

    BF33ST, BF33DX, BF39ST, BF39DX REPLACEMENT PARTS DIMPLEX BUILT IN FIREPLACE REPLACEMENT PART BF33ST BF33DX 1. LOG SET 0438200300RP 0438200300RP 2. REFLECTOR ROD 5900081000RP 5900081000RP 3. GROMMET 8500000600RP 8500000600RP 4. FLICKER ASSEMBLY 6901811200RP 6901811200RP 5. BLOWER ASSEMBLY 5300110300RP 5300110300RP 6. BLOWER MOTOR...
  • Page 9 BF45ST, BF45DX REPLACEMENT PARTS DIMPLEX BUILT IN FIREPLACE REPLACEMENT PART BF45ST BF45DX 1. LOG SET 0438550200RP 0438550200RP 2. REFLECTOR ROD 5900080900RP 5900080900RP 3. GROMMET 8500000600RP 8500000600RP 4. FLICKER ASSEMBLY 6901811200RP 6901811200RP 5. BLOWER ASSEMBLY 5300110300RP 5300110300RP 6. BLOWER MOTOR 5300110400RP 5300110400RP 7.

  • Page 10: Wiring Diagram - Lower Section

    BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX WIRING DIAGRAM - LOWER SECTION BROWN WHITE BLACK BLUE (3) BLUE (4) MARR BLACK RED (2) RED (1) WHITE BLACK RED (L2) WHITE (N)

  • Page 11: Wiring Diagram - Upper Section

    BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX WIRING DIAGRAM - UPPER SECTION...

  • Page 12: Wiring Diagram - Schematic

    BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX WIRING DIAGRAM - SCHEMATIC...
  • Page 13 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 14 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 15 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 16 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 17 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.

  • Page 18: (Unit Is Permenantly Installed In Wall)

    BF33ST, BF33DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.

  • Page 19: (Unit Is Permenantly Installed In Wall)

    BF33ST, BF33DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.

  • Page 20: Bf39St, Bf39Dx, Bf45St, Bf45Dx

    BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 21 BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 22 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 23 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 24 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 25 BF33ST, BF33DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 26 BF33ST, BF33DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 27 BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 28 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 29 BF33ST, BF33DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 30 BF33ST, BF33DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 31 BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 32 BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 33 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
  • Page 34 BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.

This manual is also suitable for:

Bf39stBf33dxBf45dxBf39dxBf45st

Table of Contents