Table of Contents
Advertisement
After you finish preparing a recording media and connecting a mixer, you can start basic recording using this
recorder.
The following explanation assumes that this recorder has been connected to an external mixing console (as explained
in the "Connecting a Mixer" section). Because the D2424LVmkII can accept 24 channel analog signals, you can
record up to 24 audio sources simultaneously.
Selecting a recording track
1.
Press the [RECORD TRACK] select key of the desired
recording track to set it in READY mode.
The "ready" track indicator (a small square) flashes
on the display.
OL
0
3
6
9
12
18
24
30
42
1
2
4
5
6
7
8
9
3
10
Flashing
Adjusting the recording level
This recorder does not have any recording level
controls. You need to adjust the recording level on the
device that outputs recording data. Use the group
master faders on the mixer (faders that control the
output level of BUSS OUTs). Set the recording tracks
on this recorder to input monitoring status so that you
can check the level adjustment.
2.
Press the [RECORD] button once. (The RECORD LED
flashes.)
The "ready" tracks enter the input monitoring status.
As you raise the group output level on the mixer, the
level meter segments of the ready tracks light up.
Adjust the level so that the "0" to "3" level segments
of the level meter light up at the highest peak.
If the "OL" segments of the meter light up, the
recording level is too high. If the recording level is
too high on a digital recorder, the recording signal
may distort, unlike an analog recorder. Especially, if
you are recording vocal or acoustic instruments, the
recording level may suddenly peak.
In this case, you may want to lower the signal peak by
applying a compressor/limiter using an insertion
connector.
Basic recording
Basic analog recording
1, 4
24TRACK DIGITAL RECORDER
POWER
RECORD TRACK
1/9/17
2/10/18
3/11/19
4/12/20
FOOT SW
ENVELOPE
ACCESS
9-16
ABS
M
S
F
PGM
OL
BIT
0
3
6
9
12
18
CLOCK
24
30
42
21
24
11
12
13
14
15
16
17
18
19
20
22
23
Model D2424LVmkII Quick Operation Guide
4 5
AUTO RTN
CLIPBOARD
AUTO PLAY
IN
OUT
START
EDIT
SETUP
SHIFT
TC READY
TC GEN
AUTO
REHEARSAL
24bit
PUNCH
96kHz
TAKE
OPTICAL
PLAY
RECORD
STOP
TRACK SHIFT
5/13/21
6/14/22
7/15/23
8/16/24
ALL READY
ALL INPUT
17-24
TRACK SHIFT
CLIPBOARD PLAY
LOCATE ABS 0
LOCATE REC END
2
3 6
3.
Hold down the [RECORD] button and press the
[PLAY] button.
The flashing RECORD LED and the track indicator (a
small square) light up steadily.
24
FS
kHz
4.
Press the [STOP] button.
INT
When the recorder section is stopped, the "Please Wait!"
message appears on the display momentarily, then
the current position appears.
The ready track indicators flash.
5.
Press the [RECORD TRACK] select keys for the ready
tracks to set the tracks in the safe status.
The flashing track indicators turn off.
6.
Hold down the [STOP] button and press the
[REWIND] button to locate the top of the Program
(ABS 0).
The top of the Program is immediately located in
LOCATE ABS 0 mode.
7.
Press the [PLAY] button.
The playback starts from the top of the Program.
Adjust the level of input signal at TAPE IN on the mixer
and monitor the sound.
Repeat the procedure described above to record more
tracks (mono track or multiple tracks). You can record
eight different sound sources on this recorder
simultaneously.
<Undo and redo recording>
If you make a mistake or you are not satisfied with the
recording, you can "undo" recording. Refer to the "Undo
and redo recording" section below.
16
AUTO RTN
AUTO PUNCH
IN
OUT
END
PGM SEL
EXIT/NO
EXECUTE/YES
PREVIEW
EJECT
CHASE
CHARACTER
LOCATE MEMORY
STORE
UNDO/REDO
PREV
NEXT
DISP SEL
RECALL
M.UNDO
PREV TC
NEXT TC
TIME BASE SEL
HOLD
LOCATE
VARI PITCH
P.EDIT
REW
F FWD
Starting recording
Stopping recording
Playing the recorded tracks
Advertisement
Table of Contents
