System I/O Address Map; Using The Actionpoint Touchpad - Epson ActionNote 900 Underwater Color Specifications

Hide thumbs Also See for ActionNote 900 Underwater Color:
Table of Contents

Advertisement

EPSON ActionNote 900 Series

System I/O Address Map

Hexadecimal Address
000-01F
020-03F
040-05F
060-06F
070-07F
080-09F
0A0-0BF
0C0-0DF
0F0
0F1
0F8-0FF
100-1EF
1F0-1F8
200-207
208-277
278-27F
2F6-2FF
300-31 F
360-36F
378-37F
380-38F
3A0-3AF
3B0-3BF
3C0-3CF
3D0-3DF
3E0-3EF
3F0-3F7
3F8-3FF
2F8-2FF
AN900-11
Device
DMA Controller 1
interrupt Controller
Timer/Counter
Keyboard Controller
RTC NMI
DMA Page Register
Interrupt Controller 2
DMA Controller 2
Clear Math Coprocessor Busy
Reset Math Coprocessor
Math Coprocessor
Available
Hard Disk Drive
Game Port
Sound Card
Parallel Port 2
Serial Port 2
Prototype Card
Reserved
Parallel Port 1
SDLC Bisynohronous 2
Bisynchronous 1
Mono Display Printer Adapter
Reserved
Color/Graphics Monitor Adapter
PCMCIA Controller
Diskette Drive Controller
Serial Port 1
IrDA Port
Installation/Support Tips
Using Low Battery Save to HDD and Instant On
The ActionNote 900 series hard disk drive is partitioned at
the factory so that these options can be used. A 26MB area
is set aside for the saved data; this ensures that there is
enough space for all memory configurations.
To prepare the hard disk drive, run the PHDISK utility,
located in the C:\PM directory. You also need to run this
utility if you upgrade your system memory. Type the
following command at the DOS prompt and press Enter:
PHDISk/CREATE
If you install a new hard disk drive and want to use the
I
Low Battery Save to HDD or Instant On options, you need
to leave sufficient space on the disk unpartitioned. The
amount of space should equal the system memory plus
2MB. After you run FDISK to partition the drive, you need
to run the PHDISK utility to configure the storage space on
the drive.
In Windows 3.1, when the computer is turned on after
using the Low Battery Save to HDD or Instant On options,
the PCMCIA services are not reinitialized. The computer
recognizes SRAM PC cards, but does not recognize most
other PC cards. You must reboot to reinitialize the services.
Using an External Monitor
When you connect an external monitor, make sure you turn it
on before you turn on the computer. The ActionNote
automatically detects the external monitor and displays data
on its screen. Press Fn F10 to switch your display from the
monitor to the LCD screen or to display
simultaneously. Resolutions up to 1024 x 768 in 256 colors
supported.
I

Using the ActionPoint Touchpad

use
If you
an external
port, the touchpad is automatically disabled. If you want to
use the touchpad, turn the computer off and then on, and
touch the ActionPoint first
Using a Serial Mouse
If you connect a serial mouse, you must use the Setup
program to disable the built-in touchpad.
Using the IrDA Port
When communicating with another IrDA-equipped device,
such as a printer or computer, ensure that the IrDA ports are
within 3 feet, with no more than a 30-degree angle in a direct
line of sight with no obstructions. See the User's Guide for
details.
10/21/95
both screens
on
pointing device connected to the mouse

Advertisement

Table of Contents
loading

This manual is also suitable for:

Actionnote 900 series

Table of Contents