Advertisement
.qMPO_RTANT= We adv s,:;yol=to assemble the t.mt once before going carnpin:!;I t o be_;omefamiliar with the
:_:,.,.,assembly of the re ii.. For thi_ model, it is "_commended two people be inTo|ved in the set up.
NOTE:
Please look _Lt_h,.;repl_Lcement pads di-:_ram to see how your frame is assembled.
,
To prolong
the life, pf'the t._r_ floor, select a low.I, clean area for the camps/to,
-
To prevent
darnag_
1_:_ t he i_ippP.r, unzip the do,:.f, ;, prior to tent set-up, to allow air to enter the tent.
* To improve the we= tiler r_i_istance of your tent, i; is advisable
to use seam seater to, _=oat all expas,_d seams.
You should app])/c
_y to ti_e underside
of the ';_/and inside _earnG of the tent.
If arcpiled to the outslde
af seams,
discoloration
of yo= ir tent #_ay,oocur.
Seam s_:_d_ris available at the c_mping
secti,',,n of your local Se_.rs store.
• For yourconvenFer
Simply unzip the sl
between the bot_o_
=_ and:,_llnproved tent funct!,._ _altty, we have developed
a s_'.lf-colltained storm flap _acket,
'rn flai_,'-"covering
the wind_ _ts and door_ and drop into the po,I;ket that has been formed
of the'..,_to_mflap and the _a ,.sh window.
STEP 3; Insert the kn_)bon the underside of the center hub
into the relnf,;rced h,_leat the center roof of the
tent. The fib _rglass sections should be extended
to hold the c:;;nter
roof of the te:nt
in place.
\
_'
of the tent. The flat, smoothside of
_
!!
the center hub, l:ould be UR Once _i
e.berg . s:,ions , so od / lA!i
_':
into the sleew,s, t
'he _b;i.l°gT_SS
_
/-/#////
_i
sections shoulld ) _;ins_!rl:ed _
////_/
soa od
/ IF ,/Fo '
ii
Locate the cent_ r =_pld_',r hub (Key 13).Go '_cthe
center roof of th._. _ ent$_nd insertone of e_.'h of the
eight fiberglass=_ctlon_:_, ate.ached to the _ _ter
hub through the _',.ntsh;_;ves at the very c,_,_arroof
STEP
STEPS:
STEP 6:
Locatethe t;h_ee fiberglass ridge poles (Key A).
Extend each pole by inserting the fiberglass
sections into the metal ferrules. Each ridge pole
will have a plastic elbow joint on each end. Slide
one ridge pc,,:_ through each of the pole sleeves
located on tlh,_ends of the tent side rooms.
Attach small hooks at each roof corner to the
holes in each of the
__---_
plastic elbov'
_..-_"_--
joints. Flexlrl ;f ti_e _
fiberglass wil be
j'_..._-'_--
necessary.
._-
x_.
Unfold the fl'_ and place over the tent.
Locate the s "<steel side uprights (Key B), Join the
upper end e'. each upright, which will have a metal
,__
ring attached for the fly attachment near the end,
I_
to the plastk, elbow joints on each ofthe fiber-
IIJ
glass r_dge I_oles. With one person on either side
of the tent, i_Jsethe side rooms by raising the side
ill
_
uprightpole_ and adiusting until the wailsare taut.
111_
The ep_.nends of tFe steel poles should rest upon
Ill _
the ground. Repeat this step with the remaining
side rooms ,_.t_d s teel side upright poles.
Advertisement
