Heat & Glo RED40 Owner's Manual
  1. Manuals
  2. Brands
  3. Heat & Glo Manuals
  4. Indoor Fireplace
  5. Heat & Glo RED40
  6. Owner's manual
Heat & Glo RED40 Owner's Manual

Heat & Glo RED40 Owner's Manual

Hide thumbs Also See for RED40:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Manual
Models:
RED40
RED40ST
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer's instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12
Owner's Manual
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fi replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other fl ammable
materials.
• Keep clothing, furniture, draperies and other fl ammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
Installation and Operation
1

Advertisement

Table of Contents
loading

Related Manuals for Heat & Glo RED40

Summary of Contents for Heat & Glo RED40

  • Page 1 Technologies suggests NFI certifi ed or factory trained This appliance is only for use with the type(s) of gas indicated professionals, or technicians supervised by an NFI on the rating plate. certifi ed professional. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 2: Congratulations

    00,000 00,000 00,000 00,000 MIN. MIN. INPUT INPUT BTUH: BTUH: 00,000 00,000 00,000 00,000 Serial Serial ORIFICE ORIFICE SIZE: SIZE: #XXXXX #XXXXX #XXXXX #XXXXX XXXXXXXX XXXXXXXX (Serie): (Serie): Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 3: Table Of Contents

    G. Active Convection Blower Replacement ... . . 46 6 Termination Locations A. Vent Termination Minimum Clearances ....21 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 4 D. Contact Information ......78  = Contains updated information. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 5: Limited Lifetime Warranty

    3 years Firebox and heat exchanger Lifetime All replacement parts 90 Days beyond warranty period See conditions, exclusions, and limitations on next page. 4021-645C 12-29-10 Page 1 of 2 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 6 B. Limited Lifetime Warranty (continued) WARRANTY CONDITIONS: WARRANTY EXCLUSIONS: This warranty is void if: LIMITATIONS OF LIABILITY: 4021-645C 12-29-10 Page 2 of 2 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 7: Listing And Code Approvals

    • A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 8: Requirements For The Commonwealth Of Massachusetts

    VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB- of the installation. STRUCTIONS”. See Gas Connection section for additional Common- wealth of Massachusetts requirements. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 9: User Guide

    Heat may damage these objects. - Adjustable safety gate. DECORATIVE DOORS SECTION 2.D. FIXED GLASS ASSEMBLY SECTION 14.H. CLEAR SPACE SECTION 2.C. Figure 2.1 General Operating Parts/Clear Space. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 10: Decorative Doors And Fronts

    • Install a switch lock or a wall/remote control with child protection lockout feature. • Keep remote controls out of reach of children. See your dealer if you have questions. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 11: Lighting Instructions (Ipi)

    For additional information on operating your Hearth & Home Technologies fi replace, please refer to www.fi replaces.com. Final inspection by Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 12: After Fireplace Is Lit

    Wall above appliance feels hot to No action necessary. This appliance ships with a non-combustible material attached. Specifi ca- the touch. tions of the attached non-combustible material are listed in Section 1.E. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 13: Maintenance And Service

    • Refer to Section 14.H for glass removal and replacement • Inspect draft shield to verify it is not damaged or missing. instructions. • Reinstall door or decorative front. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 14: Maintenance Tasks-Qualifi Ed Service Technician

    • Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary. • Check for smooth lighting and ignition carryover to all ports. Verify that there is no ignition delay. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 15: Installer Guide

    FRAMING HEADED OFF IN CEILING JOISTS (SECTION 8.C) FRAMING/HEADER (SECTION 5) WALL SWITCHES REQUIRED ACTIVE CONVECTION AND CONVECTION GAS LINE DUCTING (SECTION 11) (SECTION 9.C) Figure 4.1 Typical System Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 16: Design And Installation Considerations

    Flat blade screwdriver 1/2 - 3/4 in. length, #6 or #8 Self-drilling screws Caulking material (300ºF minimum continuous exposure rating) One 1/4 in. female connection (for optional fan). Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 17: Framing And Clearances

    See Section 9.C for more detailed information. TOP VENT ONE 90° ELBOW Inches 60-3/8 85-3/8 24-1/8 18-3/4 See Section D. Figure 5.6 & 5.7 Millimeters 1533 1270 2168 Figure 5.1 Appliance Locations RED40 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 18: Constructing The Appliance Chase

    fl oor. However, this fi replace can be elevated off the fl oor provided that the fi replace is properly supported by framing materials and the ceiling clearances are maintained. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 19 Opening Opening Opening Rear of to Ceiling Floor Flooring Appliance (Vent Pipe) (Height) (Depth) (Width) Appliance Inches 46-3/4 17-1/4 50-1/4 Millimeters 1187 1276 Figure 5.5. Clearances to Combustibles-RED40ST Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 20: Mantel And Wall Projections

    Note: All TO CEILING measurements in inches. MAX. MIN. MEASUREMENTS FROM TOP EDGE OF THE FIRESCREEN DOOR ASSEMBLY Figure 5.7 Minimum Vertical and Maximum Horizontal Dimensions of Non-Combustibles Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 21: Termination Locations

    Over 16/12 to 18/12 ..........7.0 Over 18/12 to 20/12 ..........7.5 Over 20/12 to 21/12 ..........8.0 * 3 foot minimum in snow regions Figure 6.1 Minimum Height From Roof To Lowest Discharge Opening Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 22 2 sides beneath the fl oor. venting system does not meet these requirements. • Vinyl protection kits are suggested for use with vinyl siding. Figure 6.3 Minimum Clearances for Termination Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 23: Vent Information And Diagrams

    • When penetrating a combustible ceiling, a ceiling fi restop must be installed. Horizontal • Horizontal runs of vent do not require vertical rise; Figure 7.1 horizontal runs may be level. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 24 6 ft. 1829 mm 18 ft. 5486 7 ft. 2134 mm 21 ft. 6401 8 ft. 2438 mm 24 ft. 7315 = 63 ft. (19.2 m) Maximum Figure 7.4 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 25 9 ft. 2743 mm 4 ft. 1219 mm 12 ft. 3658 mm = 63 ft. (19.2 m) Maximum = 23 ft. (7.1 m) Maximum INSTALLED HORIZONTALLY Figure 7.5 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 26 1219 mm 12 ft. 3658 mm 5 ft. 1524 mm 15 ft. 4572 mm = 63 ft. (19.2 m) Maximum = 23 ft. (7.1 m) Maximum Figure 7.6 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 27 fl ame height. If the vent confi guration has a total ver- tical of 20-50 feet, an exhaust restrictor may be needed. The exhaust restrictor can be located in the appliance manual bag. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 28 = 23 ft. (7.1 m) Maximum Note: 12 inches minimum vertical is Note: Use DVP Series required prior to attaching any elbow components only. to the appliance. Figure 7.9 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 29 RUN (FT.) DROP (FT.) 80 ft. 12 ft. MAXIMUM VERTICAL DROP NOTE: Maximum total vent run= Total vertical vent run + Total horizontal vent run Figure 7.11 Power Vent Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 30: Vent Clearances And Framing

    * Shows center of vent framing hole for top venting. The center of the hole is one (1) in. (25.4 mm) above the center of the horizontal vent pipe. Figure 8.2 Wall Penetration Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 31: Install The Ceiling Firestop

    INSTALL ATTIC INSULATION SHIELDS BEFORE OR AFTER INSTALLATION OF VENT SYSTEM 3 FASTENERS PER SIDE CEILING FIRESTOP CEILING FIRESTOP INSTALLED BELOW CEILING INSTALLED ABOVE CEILING Figure 8.4 Installing the Attic Shield Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 32: Install Attic Insulation Shield

    • Bend all tabs inward 90º around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 33: Appliance Preparation

    Remove all four screws and gently lift the panel off the appliance avoiding contact with the non-combustible board if possible. BOTTOM PANEL SCREW LOCATIONS Figure 9.1 Location of Fiberglass Rope Ring Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 34: Securing And Leveling The Appliance

    BOTH SIDES DUCT COLLAR ASSEMBLY POSSIBLE LOCATIONS FOR VENT TERMINATION OF ACTIVE CONVECTION TECHNOLOGY TERMINATION INTO INTERIOR ROOM Figure 9.2 Proper Positioning, Leveling And Securing Of An Appliance Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 35: Active Convection Technology

    4 INCH ZIP TIE CONVECTION (INCLUDED WITH FLEX DUCT) AIR DUCT 4 INCH FLEX DUCT DETAIL A FAN BRACKET ASSEMBLY Figure 9.6. Active Convection Technology Duct Venting Specifi cations. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 36: Installing Vent Pipe (Dvp Pipe)

    Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 37: Assemble Slip Sections

    • Only outer pipes are sealed, sealing the inner fl ue is not required. • All unit collar, pipe, slip section, elbow and cap outer fl ues shall be sealed. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 38: Disassemble Vent Sections

    • Remove shingles or other roof covering as necessary to cut the rectangular hole for the support box. Cut the hole 1/8 in. (3 mm) larger than the support box outline. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 39: Install Metal Roof Flashing

    • Caulk the overlap seam of any exposed pipe sections that are located above the roof line. Figure 10.14 Assembling the Storm Collar Around the Pipe Figure 10.14 Assembling the Storm Collar Around the Pipe Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 40: Install Vertical Termination Cap

    EXTERIOR be maintained. • Use an extended heat shield if the fi nished wall thickness is greater than 7-1/4 in. (184 mm). Figure 10.16 Venting Through the Wall Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 41: Gas Information

    1. Remove the glass rock media or the porcelain from the • Close the manual shutoff valve BEFORE pressure testing gas line at test pressures interior fi rebox. equal to or less than 1/2 psig. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 42: Gas Connection

    • In CANADA: Reduce burner orifi ce 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility. Figure 11.4 Gas Fitting Access Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 43: Electrical Information

    See appropriate MODULE OPTIONAL confi guration in relation to the valve in Figure 12.3. The REMOTE valve does not move. Figure 12.3. Controls Location Diagram Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 44 3 volts. 120 VAC is ELECTRICAL required at junction box. ACCESS KNOCKOUT Figure 12.5 IntelliFire Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Remote Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 45: Optional Led Lighting Circuit

    (See Figure 11.2). the junction box. See Figure 12.7. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 46: Active Convection Blower Replacement

    6. Locate the fan mount fastener on either the left or right side of the appliance. See Figure 12.14. Remove fastener. Figure 12.10 Lifting Base Pan Up and Out. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 47 Figure 12.17. Figure 12.19. Blower Tab Toward Rear SLOT ON BLOWER HOUSING Figure 12.16. Remove Mounting Plate Figure 12.20. Blower Tab Inserted into Slot on Blower Housing Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 48: Finishing

    WARNING! Risk of Fire! DO NOT use screws longer than two inches when attaching fi nishing materials to non-combustible material. Screws longer than two inches will compromise clearance and may cause overheating and fi re. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 49 If desired fi nishing includes a painted wall, 100% acrylic latex with compatible primer is recommended around this appliance. Oil-based or standard acrylic paints may dis- color due to heat exposure. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 50: Mantel And Wall Projections

    Note: All TO CEILING measurements in inches. MAX. MIN. MEASUREMENTS FROM TOP EDGE OF THE FIRESCREEN DOOR ASSEMBLY Figure 13.3 Minimum Vertical and Maximum Horizontal Dimensions of Non-Combustibles Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 51: Facing Material

    BOARD = AIR SPACE 1 IN. Figure 13.6 Framing and Framing Materials-RED40ST NON-COMBUSTIBLE BOARD ON FRONT FACE (SIDE VIEW) = AIR SPACE Figure 13.5 Framing and Framing Materials-RED40 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 52 WALL SHEATHING 7-1/4 IN. 1/2 IN. 20-3/4 IN. FACTORY-SUPPLIED NON-COMBUSTIBLE BOARD 1 IN. NON-COMBUSTIBLE BOARD ON FRONT FACE (SIDE VIEW) = AIR SPACE Figure 13.7 Overlap Fit Method Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 53 1-3/16 IN. 1-3/16 IN. 1-1/2 IN. = CLEARANCE FROM VIEWING AREA TO NON-COMBUSTIBLE FINISHING MATERIAL (INSIDE FIT METHOD) Figure 13.10 Noncombustible Surface Finishing Material 0-4 Inches Thick-Inside Fit Method Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 54: Mesh Fronts

    Engage these tabs in the slot of the brackets. MESH BRACKETS MESH FRAME ASSEMBLY HANGING TABS MESH FRAME ASSEMBLY Figure 13.11. Mesh Front Installation. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 55: Appliance Setup

     E. Rock Media A rock media kit is available for use with the RED40 and RED40ST models. Install rock media according per ad- ditional instructions included with appliance.

  • Page 56: Fixed Glass Assembly

    RED40/RED40ST GRANITE KIT 1/16 in. 1/4 in. LIGHT KIT 1/16 in. 1/4 in. PORCELAIN KIT 1/16 in. 1/4 in. GLASS CLIP GLASS TAB Figure 14.3 Fixed Glass Assembly Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 57: Troubleshooting

    Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in (3 mm). c. Module is not grounded. Verify module is securely grounded to metal chassis of appliance. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 58 150 degrees Fahrenheit. This is a safety feature for this model, but is not common. Contact your dealer for assistance. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 59: Reference Materials

    Millimeters 1321 46-3/4 1187 13-3/16 10-3/4 50-1/8 1273 25-1/16 42-3/4 1086 48-1/8 1222 18-5/8 9-1/16 3-3/4 1-1/2 4-3/4 8-1/2 42-15/16 1090 18-1/8 14-1/2 Figure 16.1 Appliance Dimensions RED40 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 60 Millimeters 1321 46-3/4 1187 13-3/16 10-3/4 50-1/8 1273 25-1/16 42-3/4 1086 48-1/8 1222 18-1/8 9-1/16 3-3/4 1-1/2 4-3/4 42-15/16 1090 8-1/2 14-1/2 17-1/8 Figure 16.2 Appliance Dimensions RED40ST Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 61: Vent Components Diagrams

    14 in. (356 mm) 5 in. 12 in. (127 mm) (305 mm) 6 in. (152 mm) DVP-HVS (Vent Support) DVP-WS (Wall Shield Firestop) Figure 16.2 DVP vent components Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 62 79 mm 117 mm Length DVP-TRAP 5-3/8 in. 9-3/8 in. Trap2 Horizontal Termination Cap 137 mm 238 mm DVP-TRAP2 DVP-TRAP1 DVP-TRAPK2 DVP-TRAPK1 DVP-HPC1 DVP-HPC2 Figure 16.3 DVP vent components Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 63 13-7/8 in. 9-1/2 in. 26 in. (352 mm) (241 mm) 660 mm 14 in. (356 mm) DVP-HSM-B Extended Heat Shield DRC-RADIUS Cap Shield Figure 16.5 DVP Series Vent Components Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 64 8-3/8 in. 5-3/4 to 8-3/8 in. 140 mm 213 mm 146 to 213 mm 3° 87° 10-1/2 in. 267 mm 10-7/8 in. 276 mm Figure 16.5 DVP vent components Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 65 114 mm (381 mm) 9-3/16 IN. (233 mm) 13-5/8 16-11/16 IN. 16-11/16 IN. (346 mm) 424 mm (424 mm) 12-1/2 IN. SLP-LPC (318 mm) SLP Low Profi le Cap Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 66: Service Parts

    Non Combustible Board, Outer 2155-461 Non Combustible Board, Inner 2155-462 Panel Cover, Side 2155-140 Vent Assembly 2155-071 Grill Panel 2155-150 Unique service parts by model on following page. 10/12 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 67 Burner Assembly NG 2155-007 Pilot Shield 2155-173 Base Pan 2155-025 Panel Cover, Side 2155-140 Vent Assembly 2155-071 Grille Panel 2155-150 Additional service part numbers on following page. 10/12 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 68 2155-149 Pilot Assembly NG 2090-012 14.6 Pilot Assembly LP 2090-013 14.7 Pilot Bracket Assembly 2155-049 14.8 Flex Ball Valve Assembly 302-320A Additional service part numbers on following page. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 69 Conversion Kit LP LPK-RED40 Pilot Orifi ce NG 593-528 Pilot Orifi ce LP 593-527 Regulator NG NGK-DXV Regulator LP LPK-DXV Unique service parts by model on following page. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 70 Bottom Plate Qty 3 req 2155-161 15.5 Access Panel Assembly 2155-060 Solid White MEDIA-WHITE Rock Onyx MEDIA-ONYX Granite GR40-L Refractory Porcelain POR40-L Additional service part numbers on following page. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 71 Base Pan 2155-151 15.5 Bottom Plate Qty 3 req 2155-161 Solid White MEDIA-WHITE Rock Onyx MEDIA-ONYX Granite GR40ST-L Refractory Porcelain POR40ST-L Additional service part numbers on following page. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 72 Refractory Porcelain POR40-L Convert from Porcelain or Granite to Metal Refractory Qty 2 req 2155-232 On/Off Switches Lighted Units Only 2155-204 Additional service part numbers on following page. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 73 Porcelain POR40ST-L Convert from Porcelain or Granite to Metal Refractory Qty 2 req 2155-232 3 On/Off Switch Lighted Units Only 2155-204 Additional service part numbers on following page. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 74 Burner Insert 2155-160 18.4 Base Pan 2155-134 18.5 Bottom Plate Qty 3 req 2155-161 18.6 Access Panel Assembly 2155-060 Refractory GR-40F Additional service part numbers on following page. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 75 18.3 Mesh Plate Qty 2 req 2155-132 18.4 Base Pan 2155-134 18.5 Bottom Plate Qty 2 req 2155-161 Refractory Granite GR40ST-F Additional service part numbers on following page. Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 76 22.1 Refractory, Corner (Qty 2 req) 2155-219 21.2 Refractory, Side (Qty 2 req) 2155-210 22.2 Refractory,Side (Qty 2 req) 2155-223 21.3 Refractory, Back (Qty 3 req) 2155-209 22.3 2155-222 Refractory, Back Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...
  • Page 77 21.1 Refractory, Corner (Qty 4 req) 2175-225 22.1 Refractory, Corner (Qty 4 req) 2155-219 21.2 Refractory, Side (Qty 2 req) 2175-224 22.2 Refractory, Side (Qty 2 req) 2155-223 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

  • Page 78: Contact Information

    5890485, 5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729, 8147240 or other U.S. and foreign patents pending. 2000-945B Printed in U.S.A. - Copyright 2012 Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12...

This manual is also suitable for:

Red40st

Table of Contents